MILL NE900WIFI User guide

Assembly and instruction manual
Series:
Steel & Glass WiFi
Please read the instructions carefully before use. Take good care of this manual for later use.
EN

Thanks for buying Mill
Our company was founded in Norway in 1992 by Cato Bryn, specializing in distribution
of oil lled radiators and other types of heaters. From 1992 to 2009, we had gained
signicant knowledge and expertise of dierent type of heaters, thus enabling us to sell to
many of the largest retailers in the Nordic countries.
In 2010, Cato’s son, Phillip joined the company. Philip looked at the heating industry with
fresh new eyes and wondered why there had been so little change with the appearance
of portable heaters in the last 20 years, especially since interior design in general had
changed dramatically over the years. Philip thought consumers should have more styles to
choose from other than the typical old-fashioned, traditional heaters.
Since heaters are part of so many homes, Philip and Cato decided to use their extensive
knowledge to re-invent the design of heaters. They wanted to create beautiful, modern
and minimalistic heaters, using the most advanced technology, that would complement
people’s homes. They launched the brand “Mill” in 2012.
Mill oers revolutionary, innovative Norwegian designs. We are continuously innovating to
complement our line of products to meet consumers’ demand.
Prospering on our success in the Nordics we decided to promote Mill at some of the
world’s largest electronic fairs and home shows in 2015 and 2016 - the feedback from
retailers and distributors all over the world were amazing. We are proud to say that
consumers in over 20 countries can now keep warm with style!

1
millheat.com
EN
Content
P. 2-3
P. 4
P. 4
P. 4
P. 4
P. 5
P. 5
P. 5
P. 5
P. 6
P. 6
P. 6
P. 6
P. 7
P. 7
P. 8
P. 9
P. 9
P. 9
P. 9
P. 10
P. 10
P. 10
Important safety information
Specications
Before rst use
First use
Minimum distances
Description of heater
Assembly
Power indicator
Temperature calibration
Resetting the heater
Memory function
“Open Window” function
Instructions
Usage without WiFi connection
Usage with WiFi connection
Color codes (WiFi control light)
Activating WiFi
Deactivating WiFi
Reconnecting to WiFi
Delete WiFi settings
Maintenance
Warranty
Waste disposal
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Please read the instructions carefully before use. Take good care of this
manual for later use.
Thanks for buying Mill

2
EN
You must obey common safety guidelines when using electrical
products, especially in the presence of children.
WARNING!
To avoid electric shock or damage due to the heat, always
make sure the plug is pulled out before the heater is moved or
cleaned.
READ THE INSTRUCTIONS CAREFULLY
• The product is intended for home use only.
• Make sure the heater is connected to the house's regular mains (230 V),
as indicated on the heater.
• New heaters will produce a specic odor when used the rst time. This
will stop aer a short time and is completely harmless.
• Check for any pieces of packing foam or cardboard that may have fallen
into the heating elements of the heater. These pieces must be removed
to avoid unpleasant odors.
• Prevent the heater from overheating – do not cover.
• Always turn o the heater and unplug it when not used for a long
period of time.
• Pay special attention if the heater is used in rooms where children, the
handicapped or elderly reside.
• The heater should not be set up directly beneath an electrical socket
outlet.
• The cord must not be laid under any kind of carpet. Make sure the cord
is laid in such a way that nobody can trip on it.
• The heater must not be used if either the cord or plug is damaged.
The heater must not be used if it has been dropped on the oor or is
damaged in any other way causing it to malfunction.
• The cord must be repaired by the manufacturer or by an expert if it has
been damaged, to avoid dangerous situations.
• Avoid using extension cords, which may overheat and could possibly
start a re.
• Never cover the air vents on the heater. Avoid potential re hazards
by making sure the air intakes are not blocked or covered. The heater
should be used in rooms with normal at oors.
• The heater should not be installed in close proximity to ammable
materials of any kind because there can always be a risk of re.
• The heater must never be used in rooms where gasoline, paint or other
ammable liquids are stored, such as in a garage.
Important safety information

3
millheat.com
EN
•Never touch an electric heater with wet hands. The heater should be
installed so a person showering or taking a bath cannot come into direct
contact with it.
•The heater becomes hot when it is on. Therefore, be careful and avoid
burning or scorching your skin.
•cool down before it is moved.
•Avoid overloading the mains (the circuit) where the heater is connected.
The heater may overload the electrical circuit if other electrical devices
are plugged into the same socket outlet.
•The product cannot be used by children under 8 years of age and persons
with reduced physical or mental abilities or lack of experience and
knowledge unless they have been given supervision or instruction in the
safe use of the product and understand the hazards involved.
•Children should not play with the product. Cleaning and maintenance
should not be done by unsupervised children.
•Children under the age of 3 should be kept away from the product, unless
they are under constant supervision.
•Children aged 3 to 8 years are only permitted to turn the product ON/OFF,
assuming the heater is mounted according to the assembly instructions
and the children have received instruction or supervision in the safe use of
the product and understand the hazards involved.
DO NOT COVER
Follow us on social media:
@millheat
millheat.co.uk
[email protected]
@
STORE THIS INSTRUCTION
MANUAL FOR FUTURE USE!
NEVER TOUCH YOUR HEATER OR ITS
CASING WITH WET HANDS!

4
EN
Model Thermostat Color Height Width Amperage
Power
(W)
IP-
grad WiFi
NE600WIFI WiFi White 40,0 cm 65,0 cm 220-240V~50/60Hz 600 IPx4 802.11b/g/n
NE900WIFI WiFi White 40,0 cm 85,0 cm 220-240V~50/60Hz 900 IPx4 802.11b/g/n
NE1200WIFI WiFi White 40,0 cm 105,0 cm 220-240V~50/60Hz 1200 IPx4 802.11b/g/n
NE800LWIFI WiFi White 25,0 cm 105,0 cm 220-240V~50/60Hz 800 IPx4 802.11b/g/n
NE1000LWIFI WiFi White 25,0 cm 121,5 cm 220-240V~50/60Hz 1000 IPx4 802.11b/g/n
AV600WIFI WiFi White 40,0 cm 66,5 cm 220-240V~50/60Hz 600 IPx4 802.11b/g/n
AV900WIFI WiFi White 40,0 cm 86,5 cm 220-240V~50/60Hz 900 IPx4 802.11b/g/n
AV1200WIFI WiFi White 40,0 cm 106,5 cm 220-240V~50/60Hz 1200 IPx4 802.11b/g/n
AV800LWIFI WiFi White 25,0 cm 106,5 cm 220-240V~50/60Hz 800 IPx4 802.11b/g/n
AV1000LWIFI WiFi White 25,0 cm 123,0 cm 220-240V~50/60Hz 1000 IPx4 802.11b/g/n
The heaters are approved for use in zone 2 in wet rooms (IPx4 approved)
ATTENTION! The heaters will be connected directly to your WiFi router and it is therefore
devices connected at the same time.
≥100 mm
≥50 mm≥50 mm
≥100 mm
≥100 mm in front
of heater
First use
Minimum Distances
transport. Contact theretailer or importer if you discover any visible damages tothe product.
Keep the outer packaging to transport the heater in the future. If you want to dispose of
the packaging, make sure it is done properly. Keep plastic bags away from children.
d period without use, the
heater can produce a burnt odor for a short time. This is normal.
Please read all the instructions carefully before use. Save the instruction manual for future use.
It is also normal for the heater to make “sounds” when it warms up or cools down.

5
millheat.com
EN
Description of heater
MILL STEEL MILL GLASS
A B
1.
2. Wall bracket
3 Temperature sensor
4. Heat emission
5. Thermostat (WiFi)
6. Steel front
1.
2. Wall bracket
3. Temperature sensor
4. Heat emission
5 Thermostat (WiFi)
6. Glass front
Assembly
A. Drill holes in the wall for holes 1 & 2. Then drill holes in the wall for the topmost holes
(holes 3 & 4 by using 6)
B. Insert the wall plugs into the drilled holes and attach the bracket with 4 screws
C. Place the heater on the lower lugs on the bracket, then hang the heater on the upper
upper lugs). Screw in the
locking screws on the top of the bracket (clockwise)
When the panel heater is using power (i.e. when it is heating), the power indicator is lit .
There may be variances between the temperature registered by the heater and the actual
temperature in the room. This can be caused by several factors, however, the most common
is that the heater is placed a distance away from where you are. As the thermostat is fixed to
the heater, it will measure the air temperature in the immediate vicinity of where it is located.
The specific conditions of the room that the heater is in may dictate that there are some
variances in the air temperature where the heater is versus where you are located. To adjust
this, all Mill heaters are equipped with a calibration function which enables you to adjust the
temperature registered by the heater. Please note: the room must have a stable temperature
for calibration to work.
Press 2 times and use + or - to set the actual temperature observed in the room.
Confirm with or wait 15 seconds for automatic confirmation.
(Can be done even if you are connected to WiFi)
Temperature calibration
Power indicator

6
EN
Resetting the heater
Turn o the heater's main switch. Press and hold while you turn on the heater's main
switch.
Memory function
The heater remembers all the temperature settings and will automatically return to
the desired temperature aer a power failure. If your heater is connected to WiFi it will
automatically reconnect with WiFi (where all temperatures are saved) aer a power cut.
“Open window” function
The heater has an «open window» function that is activated instantly when it registers a
sudden drop in temperature with more than 2 degrees Celsius in 2 minutes. The heater will
automatically stop heating and FO will be visible in the display of the heater.
The heater will automatically start heating again aer 10 minutes (the display switch from
FO to desired room temperature).
See gure 5 on separate illustration sheet
Instructions
TIPS! The thermostat can be used as a regular electronic thermostat (i.e. the heater will
maintain a constant temperature 24 hours a day). Please see the section on the electronic
thermostat for further information
Control Panel
See gure 6 on separate illustration sheet
1. Display (shows the desired room temperature by default)
2. WiFi indicator
3. Power indicator — Shows whether the heater is using power or not
4. Control button (+) (increase temperature)
5. Control button (–) (reduce temperature)
6. WiFi button
7. Function button (F)
ATTENTION! In the event of a power cut, the thermostat will reconnect with WiFi where all
the temperatures are saved.
WARNING: BEFORE THE HEATER IS TURNED ON, IT MUST BE ATTACHED TO A WALL. IF THE
HEATER IS NOT INSTALLED CORRECTLY OR IS INSTALLED ASKEW, THIS MAY CAUSE THE
HEATER TO MALFUNCTION OR IN THE WORST CASE, BE DAMAGED.
If the temperature sensor is not functioning properly, you will see this symbol
on the display. Please contact the dealer or importer.

7
millheat.com
EN
Usage without WiFi connection
Set desired temperature without WiFi connection
Press the arrow buttons to set the desired temperature. The heater keeps an even
temperature the whole day and night.
ATTENTION! Can only be done when WiFi is deactivated (see page 9 for deactivating
WiFi).
Usage with WiFi connection
A free app is available for downloading for iOS and Android.
By connecting your heaters with the iOS/Android device you can do the following:
• Control all your heaters situated in multiple locations . Everything is controlled with the
Millheat-app (with same user)
• Set up weekly programs (or use the standard program already available in the app) by
using the 3 modes: Comfort, Sleep, Away
•
•
There is no need to edit your program if you get home earlier than normal one day
• Enable vacation mode for saving energy while you are away. The app will automatically
increase the temperature in your house before you get back home
• Share your house with other family members, making control easy
•
manually, so that the heaters keep an even temperature throughout the whole day and
night.
To download the app search for “millheat” in Appstore or Google Play and
install the app on your device.
Before use:
Be aware that the Millheat-app must be installed before you can connect your heaters
to your WiFi network. You can then simply follow the instructions given in the app when
connecting your heaters. The heaters will connect directly to your router via WiFi with 2,4
Ghz mode b/g/n. Minimum OS requirement: iOS 8.0 and Android 4.0.

8
EN
Go to our help desk at www.millheat.com for more information or if you
have any questions regarding the Millheat-app, connecting to WiFi or other
related questions.
ATTENTION! The heaters will be connected directly to your WiFi router and it
number of active devices connected at the same time.
Color codes (WiFi control light)
The heater has not been connected to WiFi. The heater keeps an even
temperature throughout the whole day and night.
The heater is online in the Millheat cloud
1. The heater’s WiFi is deactivated by the user
2. When installing/connecting the Millheat-app and cloud, the light will flash in
various speed. This is normal.
The heater has a problem connecting to or finding the WiFi signal. Please do the
following:
1. Please turn the heater OFF and ON again.
2. Please restart the WiFi router
3. Please check the WiFI router to make sure the capacity is sucient for the
number of active devices connected at the same time
4. Please make sure 2,4 Ghz is activated. If the problem persists we recommend
you to deactivate 5 Ghz during the installation. Aer the installation 5 Ghz
can be activated again.
The heaters are oine and have no contact with the Millheat cloud

9
millheat.com
EN
Reconnecting WiFi
Press the WiFi button 1 time. Relevant only if WiFi is already installed.
Deactivating WiFi
Press 1 time on the WiFi button. The heater can now be used as described on page 7
(usage without WiFi connection). Relevant only if WiFi is already installed.
Activating WiFi
Press «add heater» on the home screen in the Millheat-app. Follow the instructions in the
app.
See gure 8 on separate illustration sheet
See gure 10 on separate illustration sheet
See gure 9 on separate illustration sheet
Delete WiFi setting
Delete WiFi-settings: Press and hold WiFi button for 3 seconds.
The heater can also be reset to the factory settings by doing the following: Turn o the
heater’s main switch. Press and hold while you switch on the heater’s main switch.
See gure 11 on separate illustration sheet

10
EN
Maintenance
Warranty
Waste disposal
1. For cleaning, always unplug the heater and leave it to cool.
2. Wipe the heater regularly with a damp cloth and dry the surface before turning on the
heater again.
3. The heater must be cleaned at least once a month during the heating season.
CAUTION! The heater should never be immersed in water.
Avoid using detergents to clean the heater.
Never let any water get inside the heater; this can be hazardous.
4.
5. The heater can be stored in a dry and clean place.
6. If the heater stops working, do not attempt to repair it yourself because it can cause a
The warranty is valid for 2 years. The heater will be repaired or replaced during this
time should any malfunction occur. The warranty applies if the heater is used according
to these instructions and the customer can present a purchase receipt. If the heater
malfunctions in any way, please contact the store where it was purchased or the importer.
This mark on a product and/or accompanying documents indicates that when it is
to be disposed of, it must be treated as Waste Electrical & Electronic Equipment (WEEE).
Any WEEE marked waste products must not be mixed with general household waste, but
kept separate for the treatment, recovery and recycling of the materials used. For proper
treatment, recovery and recycling; please take all WEEE marked waste to your Local
Authority Civic waste site, where it will be accepted free of charge. If all consumers
dispose of Waste Electrical & Electronic Equipment correctly, they will be helping to save
valuable resources and preventing any potential negative eects upon human health
and the environment, of any hazardous materials that the waste may contain.
Mill International B.V. - www.millheat.com
www.millheat.co.uk
[email protected]
Designed by Mill in Norway ®All Rights Reserved.
Made and assembled in China.
Exclusively distributed and imported by BML L24 9WD UK ©2017