MILL SG2000MEC User guide

ASSEMBLY AND INSTRUCTION MANUAL (EN)
Please read the instrucons carefully before use. Take good care of this manual for later use.
This assembly and instrucon manual applies to the following products:
SG2000MEC, SG2000LED, SG2000GLASS
Series: Convecon

Important safety informaon
You must obey common safety guidelines when using electrical products, especially in the presence of children.
WARNING! To avoid electric shock or damage due to the heat, always make sure the plug is pulled out before the heater is moved
or cleaned.
Read the instrucons carefully.
The product is intended for home use only.
Make sure the heater is connected to the house's regular mains (230 V), as it indicated on the heater.
New heaters will produce a specic odor when used the rst me. This will stop aer a short me and is completely
harmless.
Check for any pieces of packing foam or cardboard that may have fallen into the heang elements of the heater. These
pieces must be removed in order to avoid unpleasant odors.
Prevent the heater from overheang – do not cover.
Always turn o the heater and unplug it when not used for a long me.
Pay special aenon if the heater is used in rooms where children, the handicapped or elderly reside.
The heater should not be set up directly beneath an electrical socket outlet.
The cord must not be laid under any kind of carpet. Make sure the cord is laid in such a way that nobody can trip on it.
The heater must not be used if either the cord or plug is damaged. The heater must not be used if it has been dropped on
the oor or is damaged in any other way causing it to malfuncon.
The cord must be repaired by the manufacturer or by an expert if it has been damaged, to avoid dangerous situaons.
Avoid using extension cords, which may overheat and could possibly start a re.
Never cover the air vents on the heater. Avoid potenal re hazards by making sure the air intakes are not blocked or
covered. The heater should be used in rooms with normal at oors.
The heater should not be installed in close proximity to ammable materials of any kind because there can always be a risk
of re.
The heater must never be used in rooms where gasoline, paint or other ammable liquids are stored, such as in a garage.
Never touch an electric heater with wet hands. The heater should be installed so a person showering or taking a bath
cannot come into direct contact with it.
The heater becomes hot when it is on. Therefore, be careful and avoid burning or scorching your skin.
The heater must be switched o, the plug removed and the heater must cool down before it is moved.
Avoid overloading the mains (the circuit) where the heater is connected. The heater may overload the electrical circuit if
other electrical devices are plugged into the same socket outlet.
EN 2 millheat.com

The device cannot be used by children under 8 years of age and persons with reduced physical or mental abilies or lack of
experience and knowledge unless they have been given supervision or instrucon in the safe use of the device and
understand the hazards involved.
Children should not play with the device. Cleaning and maintenance should not be done by unsupervised children.
Children under the age of 3 should be kept away from the device, unless they are under constant supervision.
Children aged 3 to 8 years are only permied to turn the device ON/OFF, assuming the device is mounted according to the
assembly instrucons and the children have received instrucon or supervision in the safe use of the device and
understand the hazards involved.
EN 3 millheat.com

STORE THIS INSTRUCTION MANUAL FOR FUTURE USE!
NEVER TOUCH YOUR PANEL HEATER OR ITS CASING WITH WET HANDS!
EN 4 millheat.com
Model Thermostat Color Amperage Power (W) Fan
SG2000MEC Mechanical White ~230 V/50 Hz 2000 No
SG2000LED Electronic White ~230 V/50 Hz 2000 Yes
SG2000GLASS Electronic White ~230 V/50 Hz 2000 Yes
Specicaons
Before rst use
Aer unpacking the heater, check to make sure the product was not damaged during transport. Contact the retailer or
importer if you discover any visible damages to the product.
Keep the outer packaging to transport the heater in the future. If you want to dispose of the packaging, make sure it is
done properly. Keep plasc bags away from children.
First use
Aer turning on the heater for the rst me or aer an extended period without use, the heater can produce a burnt odor
for a short me. This is normal.
Please read all the instrucons carefully before use. Save the instrucon manual for future use.
CAUTION! This heater is only designed to be used for supplementary heang, and as such must only be used under
supervision.
DO NOT COVER

EN 5 millheat.com
Descripon of
the heater
SG2000MEC
SG2000LED/SG2000GLASS
1. Heat emission
2. Thermostat
3. Output selector
4. Legs (plasc)
Parts SG2000MEC
 4 screws (pre-mounted)
 2 foot brackets
 2 rails for the feet
1. Heat emission
2. LED display
3. Thermostat + output selector
4. Fan
5. ON/OFF
6. Legs (aluminium)
Parts SG2000LED/SG2000GLASS
 8 screws (4 of which are pre-mounted)
 2 foot brackets
 2 rails for the feet

EN 6 millheat.com
Assembly SG2000LED/SG2000GLASS
1. Insert both legs into the brackets so you get a stable foot (as shown in Picture 1 below).
2. Aach the legs to the brackets by ghtening 2 screws into each bracket (see the picture below).
3. Remove the pre-mounted screws from the boom of the heater and place the heater gently on its head to
mount the feet.
4. Two screws must be fastened on each foot bracket (as shown in Picture 2 below).
5. NEVER USE THE HEATER BEFORE THE LEGS HAVE BEEN TIGHTLY SCREWED.
Assembly SG2000MEC
1. Insert both legs into the brackets so you get a stable foot (as shown in Picture 1 below).
2. Remove the pre-mounted screws from the boom of the heater and place the heater gently on its head to
mount the feet.
3. Two screws must be fastened on each foot bracket (as shown in Picture 2 below).
4. NEVER USE THE HEATER BEFORE THE LEGS HAVE BEEN TIGHTLY SCREWED.

SG2000MEC – Instrucons
CAUTION! This heater is only designed to
be used for supplementary heang, and as
such must only be used under supervision
Control panel for SG2000MEC
1. Thermostat. Adjust the desired heat seng
2. Output selector:
0: OFF
|: 750 W
||: 1250 W
|||: 2000 W
WARNING: Be sure the foot is ed correctly and according to the instrucons before using the heater!
Use
1. Set the output selector to the OFF posion (0) and the thermostat to minimum. Plug the heater into a grounded outlet.
2. Set the output selector to posion |, || or |||. Turn the thermostat up to the maximum posion. When the desired room
temperature has been reached, turn the thermostat slowly down unl you hear a click. The thermostat can now remain in
this posion unl a dierent room temperature is desired. As soon as the room temperature falls below this level, the
heater will automacally switch on again. When the room has again reached the desired temperature, the heater will
switch o again.
3. If you wish to change the room temperature, repeat the instrucons in step 2.
4. The heater has an overheat protecon that turns the device o if any parts become extremely hot.
5. To switch the heater o, turn the output selector to the 0 posion. If the heater will be le unused for a longer period of
me, pull out the plug.
EN 7 millheat.com

SG2000LED/SG2000GLASS – Instrucons
CAUTION! This heater is only designed to
be used for supplementary heang, and as
such must only be used under supervision
Control panel for SG2000LED/SG2000GLASS
1. Thermostat and output selector:
i. Turn the selector to the le to decrease the temperature, and turn the selector to the right to increase the temperature.
ii. Push the buon to change the desired power level. 3 power levels: 750, 1250 and 2000 W.
2. Fan ON/OFF (see step 8 in the instrucons on the next page for more informaon on its use)
3. ON/OFF buon
4. Power indicator — Shows whether the heater is using power or not
5. Indicates the output level
6. Indicates whether the fan is acvated
7. Desired room temperature
WARNING: Be sure the foot is ed correctly and according to the instrucons before using the heater!
EN 8 millheat.com
Display SG2000LED
Display SG2000GLASS
SG2000LED SG2000GLASS

EN 9 millheat.com
Using SG2000LED/SG2000GLASS
1. Plug the heater into a grounded outlet.
2. Press the ON/OFF buon.
3. Choose the desired power |, || or |||, by pressing the output selector. Turn the thermostat to the desired
temperature while looking at the display. As soon as the room temperature drops below this level, the heater will
automacally start again. When the room has reached the desired temperature again, the heater will turn itself o.
4. The thermostat goes from 5 to 35°C.
5. If you want to change the temperature in the room, repeat step 3.
6. Press the Fan buon to start the fan. Note that the fan is only acve when the heater is heang up (when the power
indicator is on).
7. The heater has an overheat protecon that turns the device o if any parts become extremely hot.
8. If the temperature sensor is not funconing as it should, will be shown on the display. In such instances, the
heater will switch itself o. Please contact your distributor or importer.
9. To turn o the heater, press the ON/OFF buon. Should the heater be le unused for a longer period of me, pull out
the plug.
Temperature calibraon
*Should any deviaons occur between the desired and actual temperature in the room, it can
be easily adjusted (the heater should have been set to the same seng for at least 12 hours in
order to be sure a calibraon is necessary).
Press and hold for 5 seconds and use + or − to set the actual temperature observed in the
room. Conrm with or wait 15 seconds for automac conrmaon.

Maintenance
1) For cleaning, always unplug the heater and leave it to cool.
2) Wipe the heater regularly with a damp cloth and dry the surface before turning on the heater again.
3) The heater must be cleaned at least once a month during the heang season.
CAUTION! The heater should never be immersed in water.
Avoid using detergents to clean the heater.
Never let any water get inside the heater; this can be hazardous.
4) Dust etc. should be removed with a so cloth.
5) The heater can be stored in a dry and clean place.
6) If the heater stops working, do not aempt to repair it yourself because it can cause a re hazard and/or electric shock.
Warranty
The warranty is valid for 2 years. The heater will be repaired or replaced during this me should any malfuncon occur. The
warranty applies if the heater is used according to these instrucons and the customer can present a purchase receipt. If the
heater malfuncons in any way, please contact the store where it was purchased or the importer.
Waste disposal
The symbol indicates that this product is not to be disposed of together with household waste. This product must be
delivered to a recycling service or container for electrical appliances and electronic equipment. This is done to avoid health
risks and prevent harm to the environment. Local businesses (or the environmental staon in your neighborhood) are
required by law to accept and recycle such products, as a means of environmentally sound disposal.
Mill Internaonal AS
Grini Næringspark 12
1361 Osteras
Tel.: [phone]
www.millheat.com
EN 10 millheat.com