Mindray Panorama User manual

Panorama®
Datascope
Software Version 8.2X and below
Quick Reference Guide

Note: The Quick Reference Guide is not intended as
a replacement to the Operating Instructions. Prior to
operating equipment, the user must be familiar with
the Operating Instructions Manual contents.
This document is a guideline only to be used as an
aid to comprehensive Inservice Training.
P/N: 0002-08-7538 Rev C
Panorama®is a registered trademark of Mindray DS USA, Inc.

Table of Contents
Print Real-Time Waveforms ...............................1
PatientDemographics ...................................1
Standby .................................................2
Discharge................................................4
Display..................................................5
PatientAlarms...........................................6
To Mute Alarms ..........................................7
To Acknowledge Latched Alarms .........................7
View List Trends..........................................8
View Events..............................................8
View Disclosure ..........................................9
View ST Data............................................10
P/N: 0002-08-7538 Rev C

Print Real-Time Waveforms:
To print a recording of current waveform data at Panorama
Central Station,
a. Select the REC key adjacent to the desired patient’s
waveform.
b. To adjust which waveforms are printed for the
selected patient tile, select the PATIENT SETUP menu
button PRINT SETUP tab.
Patient Demographics:
To enter demographics at Panorama Central Station,
a. Select PATIENT SETUP menu button.
The Demographics Tab will be displayed.
b. Select patient tile by tapping patient data tile
or waveform area.
c. Select the text box in the Demographics tab to
produce on-screen controls for entering data.
d. Enter desired text.
e. If using a bedside monitor, the information entered
at the Panorama will be automatically sent to the
bedside monitor’s demographics area.
Demographic information that has been entered at
the bedside monitor will be automatically sent to the
Panorama Central Station’s demographic area for that
patient tile.
1
P/N: 0002-08-7538 Rev C
Panorama®Quick Reference Guide

Standby:
The Standby mode will disable all of a patient’s alarms at
the Panorama Central Station, and will suspend
processing of patient data, allowing the user to
disconnect a patient from a monitor without losing
the patient’s historical data and set-up priorities. Patients
should be closely observed if the monitoring system is
placed in Standby mode.
To enter the STANDBY mode at the Panorama Central
Station,
a. Select PATIENT SETUP menu button.
b. Select patient tile by tapping patient data tile or
waveform area.
c. Select the STANDBY tab.
  •Select“PanoramaStandbyOnly”buttonto
place only the Panorama Central Station into
the Standby mode.
  •Select“PanoramaandBedsideStandby”toplace
the Panorama Central Station and the bedside
monitor into the Standby Mode.
d. You may select a patient location by pressing over
thelocationintheStandbyListBox,andthepressing
the SELECT button.
2
P/N: 0002-08-7538 Rev C
Panorama®Quick Reference Guide

To enter the STANDBY mode at the bedside monitor,
a. Press the STANDBY key on the front panel of the
bedside monitor.
b. This will place the bedside monitor and the
Panorama Central Station into Standby mode.
To remove patient from PANORAMA STANDBY ONLY mode,
a. Select PATIENT SETUP menu button.
b. Select patient tile by tapping patient data tile or
waveform area.
c. Select the STANDBY tab.
 d. Selectthe“ResumeMonitoring”buttontoresume
monitoring at the Panorama Central Station.
To remove patient from PANORAMA AND BEDSIDE STANDBY
mode,
a. To remove a patient from Standby mode press
the STANDBY button on the front panel of the
bedside monitor. This will resume monitoring at the
Panorama Central Station and the bedside monitor.
To remove patient from STANDBY at the bedside monitor,
a. To remove a patient from Standby mode press
the STANDBY button on the front panel of the
bedside monitor. This will resume monitoring at the
Panorama Central Station and the bedside monitor.
3
P/N: 0002-08-7538 Rev C
Panorama®Quick Reference Guide

4
Discharge:
The discharge function allows the discharge of patient
information, and to reset the Panorama Central Station for
the next patient.
To discharge at Panorama Central Station,
a. Press PATIENT SETUP.
b. Select patient tile by tapping over patient data
or waveform area.
c. Select the DISCHARGE tab.
d. Press DISCHARGE PATIENT.
 e. Apromptwillappearthatasks“Areyousure?”
f. Selecting YES will erase all data stored at the
Panorama.
g. Selecting NO will continue monitoring of that patient.
h. Discharging patient at Panorama does not erase
information stored at bedside monitor.
To discharge at bedside monitor,
a. Press the DISCHARGE key on the front panel of the
bedside monitor.
b. Selecting the DISCHARGE FROM BOTH option will
erase all information stored at the Panorama and at
the bedside monitor for that patient.
*If a patient is discharged from the Central Station but not
from the patient monitor, the Central Station tile will not
P/N: 0002-08-7538 Rev C
Panorama®Quick Reference Guide