Minerva 3398ss-m-SHL User manual

Tools required:
Components (Label - Description)
**Open all drawers and
boxes to check for
parts before
beginning assembly.
Qty. S ketchPart
I
H
F
E
D
20
10
4
24
16
4
8
Description
Short Allen bolts
Medium Allen bolts
Long Allen bolts
Genesis Ultra Double-sided Styling Station
Model #3398ss-m-SHL
Assembly Instructions
Handle screws
Handles
Washers
Short bolt anchors
5Appliance rings
Flat-top Allen bolts
8
G
1 - Base
2 - Bottom cabinet section
3 - Top cabinet section
4 - Mirror panel
5 - Rear panel
PARTS LIST**
Large Allen wrench (included)
Sm all Allen wrench (Included)
Phillips-head screwdriver (Not included)

1
3
2
3) Turn wrench to tighten
2) Insert bolt into
anchor
1) Insert and
hold steady
1) Remove all the drawers from the top cabinet section (3) by pressing the black release tabs in the
glides (one up, one down) and pulling. Lay drawers out in proper order for replacement.
2) Set the top cabinet section (3) on top of the bottom cabinet section (2), aligning the 4 small holes
in each.
3) Drop the 4 short bolt anchors (I) into the holes in the bottom of the top cabinet section (3) and
secure by screwing in the 4 short Allen bolts (D) with washers (H) upward through both cabinet
sections into the anchors. Use the small Allen wrench to hold the anchors in place while
tightening the bolts (see magni cation).
I
I
D
H
I
D
H
D
D
I
H
H
Hx4
Dx4
Dx2 Ix4
2 - Mounting the top cabinet section
x4
H
x4
E
1) Remove all the drawers from the bottom cabinet
section (2) by pressing the black release tabs in
the glides (one up, one down) and pulling.
Lay drawers out in proper order for replacement.
2) Set the bottom cabinet section (2) on top of the
base (1), aligning the 4 small holes in each.
3) Secure the bottom cabinet section (2) to the
base (1) using the 4 medium Allen bolts (E)
and 4 washers (H) as shown.
1 - Mounting bottom cabinet section
E
H
H
E
HH
E
E
1
2
3 - Mounting the optional shelf
1) Find the two screw holes at the front of mirror panels.
2) Align the two screw holes on the small shelf.
3) Use allen bolts to secure in place.

1) For shipping,the drawer handles (J) are attached to the insides of the drawer faces. Using a
Phillips-head screwdriver, remove the 2 screws (K) in each and reattach the handles on the
front of the drawers.
2) Drop the metal appliance rings (L) into the holes in the appliance drawer.
3) Slide the drawers back into their respective glides.
L
L
L
L
L
J
K
K
K
K
J
G
G
F
G
F
G
G
G
F
F
F
F
FG
F
G
G
G
FF
F
G
F
G
G
FG
F
H
H
H
H
H
H
HH
F
G
G
F
2
3
1
L
J
Kx20
x10
x5
5 - Replacing the drawers
5
4
x16
G
x16
F
Hx8
1) Rotate the mirror panel (4) such that the holes in the back of the panel are aligned with the holes
in the front faces of the bottom and top cabinet sections (2, 3).
2) Anchor the mirror panel to the cabinets by using the long Allen bolts (F) and washers (H) in the
bottom 4 sets of holes and the at-top Allen bolts (G) without washers in the top 2 sets of holes.
3) Repeat steps 1 and 2 for the back panel (5), using the same conguration of bolts and washers.
4 - Mounting the mirror and back panels