Mini Gadgets Bush Baby Stealth Air Freshener User manual

1 Version 1.5
Bush Baby Stealth Air
Freshener Manual
SKU: BBSAirFreshener

2 Version 1.5
THANK YOU FOR PURCHASING THE BUSH
BABY STEALTH AIR FRESHENER HIDDEN
CAMERA
Please read this manual before operating the
camera and keep it handy.
Your purchase should include:
1 x BushBaby Stealth Air Freshener
1 x 16GB MicroSD Card
1 x MicroSD Card Reader
1 x User Manual
1 x Remote
1 x MicroUSB Cable
1 x AC Adapter
1 x Charging Adapter with Indicator
Lights

3 Version 1.5
GET FAMILIAR WITH YOUR AIR FRESHENER CAMERA

4 Version 1.5

5 Version 1.5

6 Version 1.5
BEFORE YOU START
Note: If you are not located in the US, or if you intend
to use this product anywhere other than the US, you
will need to purchase a converter in order to use the AC
wall plug in and avoid damaging the product. Because
different countries use different voltages in their
electrical wiring, you will need a converter that adapts
to the current in your particular country.
Please note that this is not a functioning air freshener.
OPERATING THE BUSHBABY CAMERA
IMPORTANT NOTICE: Allow the device to charge 6 –8
hours before using.
REMOVING AND CHARGING THE BATTERY
1. Remove battery from the inside of the device.
2. Disconnect the battery connector that is
connecting the battery to the circuit board (red
piece connecting black and red wires). Be

7 Version 1.5
careful not to pull on the wires as that could
damage them.
3. Connect the connector on the battery to the
connector on the charging adapter (see page
5).
4. Plug the provided USB cable into the other end
of the charging adapter.
5. Plug the other end of the USB cable into the
wall AC adapter and plug it into the wall.
6. Wait 6 to 8 hours.
a. The larger the battery capacity, the
longer it takes to charge.
HOW TO TURN ON THE BUSHBABY CAMERA
1. Press the Power Button on the remote control
one time (see page 4). Your device is on when
the led indicator turns on.
2. The device is now in Standby mode.
HOW TO RECORD VIDEO ON THE BUSHBABY CAMERA
1. In standby mode, press the Video button on the
remote control one time (see page 4). The

8 Version 1.5
indicator light inside of the device will flash
three times and then turn off.
a. Videos will be recorded continuously
and saved in 20 minute intervals.
HOW TO SET UP MOTION DETECTION
1. In Standby mode, press the Motion Detection
button one time (see page 4). The indicator light
will flash three times and then turn off.
2. The unit is now in motion detection mode and
will begin recording video once motion is
detected. There will be no LED indicator to
indicate when motion is detected.
3. When you wish to exit motion detection mode,
press the “motion detection” button once more.
The device will enter standby mode.
HOW TO STOP RECORDING
1. To stop recording, you will need to press the
same button you used to begin recording.
a. If you pressed the Video button, press
the Video button once more.

9 Version 1.5
b. If you pressed the Motion button, press
the Motion button once more.
2. The device will reenter Standby mode (solid
light).
HOW TO TAKE A PICTURE
1. While in Standby mode, press the Picture Button
one time (see page 4). When the indicator light
flashes one time, 1 picture will be taken
accordingly.
2. The device returns to Standby mode once 1
picture has been taken.
MICROSD CARD SLOT
1. To access the MicroSD Card Slot, you must open
the BBSAirFreshener by pressing the button
located on the top of the product and then pull
the sides so that it opens.
2. Gently push the MicroSD Card into the slot. The
gold contacts on the card will be inserted first,
and they should face the main circuit board. You

10 Version 1.5
will feel some spring resistance before the card
clicks in to place.
a. Never force the card into the Card Slot
under any circumstances, otherwise the
unit or the MicroSD card itself will be
damaged.
3. To remove the SD card, gently push the card in
so that it clicks.
4. The internal spring tension will eject the card.
MicroSD cards 65GB and above will require special
formatting to work. The device will not function with
these cards if they are not properly formatted
beforehand.
Visit www.mgidownloads.com/Software and download
the “guiformat.zip” file. Extract the files and follow the
instructions in the “64GB SD Card Formatting.pdf”
document.