MINOURA Bike Cradle 4 User manual

- 3 -
Extra Bike Hanger Kit Bike Cradle 4 instructions manual
(ver.1.1 2014/8)
Schematics
Left Side Arm (foreside)
Right Side Arm
(backside)
Cradle Cap
Hook
Main Bracket
Clamp
Shim
(use if the pillar diameter is
smaller than 43mm)
Spacer Collar
(Left side only)
Pivot-Pin
Pivot-Pin
Fixing Screw
Hook Fixing Screw
Left Arm Angle
Adjusting Screw
Right Arm
Angle Adjusting
Screw
Arm Connecting
Screw
Clamp
Tightening
Screw
How To Install Cradle4
1
Widely open the clamp then
wind arond the pillar.
Make sure the single fatter arm
is located on the right side, and
two narrower arms are located
on the left side (see Fig. B).
Opposite combination doesn't
work.
If the pillar diameter is smaller
than 43mm, install the supplied
plastic Shim first, then wind the
clamp over the shim (see Fig. C).
Make sure you install the Shim
in correct direction. Dual rail
must fit to the single arm side.
Required Tool: M5 Hex Wrench (not supplied)
At first, remove the Pivot-Pin, Pivot-pin Fixing
Screw and Clamp Tightening Screw to open the
clamp (see Fig. A).
2
Shim
(Fig. A)
(Fig. B)
(Fig. C)
<Applicable Tube Diameter: 38 – 45mm>
40mm = for BikeTower / BikePit upper pillar
45mm = for BikeTower / BikePit lower pillar, P-500 / 600 / 700 pillar
CRADELE 4 Bike Cradle 4's arm has di󱐯erent shape from Bike Cradle 3. It's the bent type
in order to enable to place the bike further from the pillar to avoid conicting
with the pedal.
!We suggest wrapping
the hook with bar tape to
minimize discoloring of
lighter colored frames.
49 44924 42220 2

- 4 -
3
!Do not remove the Arm Connecting Screw.
Just loosen.
Each arm is fully angle
adjustable in +/- 35 degrees in
order to fit various types and
sizes of bike frame (see Fig. G).
!Do not set both hooks higher than level.
The hook which holds the main load must
be located lower than the clamp body.
!Tighten every bolt rmly before loading the
bike. If the arm xing screws have been
loosened, they may come down due to the
bike weight and may drop the bike in the
worst case.
Insert the Pivot-Pin to the clamp from
bottom hole, and screw the Pivot-Pin
Fixing Screw with a washer to hold the
pin (see Fig. D).
You don't have to tighten the bolt
firmly yet.
4
Rotate the Pivot-Pin to align the thread
hole on the pin and the side hole on
the clamp body, then screw the Clamp
Tightening Screw.
(see Fig. E).
You don't have to tighten the bolt firmly
yet.
5
After fixing the clamp height
and angle, tighten the Clamp
Tightening Screw first (see Fig. F).
(Tightening Torque: 3 N.m)
After that, tighten the Pivot-Pin
Fixing Screw to secruely hold the
clamp.
(Fig. D)
(Fig. E)
(Fig. F)
6
(Fig. G)
7To change the arm angle, insert an M5 hex
wrench into the center hole on the Cradle Cap
then loosen the Arm Connecting Screw.
(see Fig. H)
(Fig. H)
8Loosen the backside screw which holds the arm,
grab the arm and change the arm angle.
After changing the angle, tighten the screw firmly.
(see Fig. I)
(Fig. I)
Contact
MINOURA JAPAN
1197-1 Godo, Anpachi, Gifu 503-2305
Phone [phone] / Fax [phone]
[email protected] / www.minoura.jp
Made in Japan
If you need help or have a question, please contact the shop first
where you originally purchased this product.
If you cannot get enough service or answer from them, you can
contact us directly.