MINOURA VERGO-TF User manual

For More Information
Warranty Period
Minoura offers 1-year limited warranty to the original user from
the date of your purchase.
This program covers any defects caused by the manufacturer's
mistakes during production. It will not cover any results caused
by the user's misuse, natural wear or unauthorized modifications.
For more information, visit www.minoura.jp.
VERGO-TF Wheel Holder
– instructions manual
About The Wheel Holder
Example Style:
Installing on the rail end of
VERGO-TF2 with two bikes
Parts Name
MINOURA Japan Headquarters (for ALL customers)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Fax: [phone]
Email: [email protected]
Web: www.minoura.jp
MINOURA North America (for U.S. residents only)
Hayward, California, U.S.A.
Phone: [phone]
Fax: [phone]
Email: [email protected]
Made in Japan
(ver.1.4 2017/8)
• Front wheel needs to be removed to mount bike to VERGO-TF. This Wheel Holder safely holds the
removed wheel without worry of damaging your wheel or car.
• Can hold up to two wheels on the single arm. For standard 9mm quick release type wheel only. Any other
system such as Thru Axle type hub cannot be used.
Arm
Wheel Installation Position #2
Wheel Installation Position #1
Angle Adjust
Knob Nut
Knob Bolt
Bracket
Plate Nut
Please note, the hole
diameters are different
between the right and
left sides.
!

1
2
!Only the case of using position #2, if the
acorn spring has been damaged due to
the twisting of the Q/R lever, try to ip
the spring as the larger diameter side
facing inward.
How To Install Wheel Holder
Rail
End Base
Loosen the small knob bolt under the End Base and
remove the End Base from the Rail.
Insert the Plate Nut into the upper gutter on the Rail.
How To Fold Down The Arm
1
2
3
When not in use, you can fold down the arm compactly.
Loosen the Knob Bolt
to turn the Bracket
Fold down the arm
How To Mount Wheels
Wheel Installation Position #1
Loosen the skewer nut, push the lever side shaft
to make large space on the nut side.
Drop your wheel into the cut out on the top of the
arm and close the lever to lock securely.
Wheel Installation Position #2
Remove both skewer nut and the acorn spring
then insert the shaft together with the 9mm
diameter threaded end into the LARGER hole.
Tighten the nut and spring, then fold down the
lever to lock securely.
Wheel on position #1 Wheel on position #2
(wheel installation
direction is disignated)
!The arm is made of hollow alloy tubing.
Tightening too much can damage it.
If you have tightened the skewer too
strongly, the arm could be damaged.
Adjust the clamping force just enough
to hold the wheel in place.
!Minoura recommends that the wheel be
just touching the oor, not suspended in
the air.
Even if you tighten the knob rmly, it
would be difcult to keep the wheels in
the air.
You don't have to remove the quick release
skewer from the wheel when mounting the
wheel on both position #1 and #2.
Be sure the quick lever is located outside on
both cases.
Be sure these hole sizes are
different between the right side
and the left side.
The wheel must be installed on
the larger hole side.
If necessary, turn the Arm to
match your desired direction.
Put the Knob Bolt into the hole on the Bracket, and
screw into the Plate Nut slightly as the bolt tip doesn't
come out from the Plate Nut.
3Install the End Base
to the Rail again.
Tighten the Knob Bolt to hold the
Wheel Holder securely.