Minuteman Powerboss PB32036CE Guide

Revised 8/03
OPERATION SERVICE PARTS CARE
PowerBoss 32
Floor Scrubber
Traction Driven
Model:
PB32036CE
PB32036QP

TABLE OF CONTENTS
Page
Safety Instructions 1
Electrical Requirements 2
Control Panel Identification 3
Squeegee Adjustments 4
Operating Instructions 5
Maintenance of Machine 6 & 7
Main Polyethylene Components 8 & 9
Recovery Tank 10
Solution Tank 11
Drive Assemblies 12 & 13
Main Frame 14 & 15
Console Assembly 16 & 17
Scrubhead Assembly 18
Squeegee Mechanism Assembly 19
Squeegee Assembly Complete 20
Wiring Diagram Standard Model 21
Wiring Diagram CE Model 22

1
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
Operators must read and understand this manual before operating or maintaining this equipment.
•Keep hands and feet clear of moving parts while machine is in operation.
•All switches must be in the “OFF” position when charging batteries.
•Electrical motors and components can cause an explosion when operated near explosive materials
or vapors. Do not operate this machine near flammable materials such as solvents, thinners, fuels,
grain dusts, etc.
•Make sure all switches are turned “OFF” and battery connections are removed before performing
any maintenance procedures.
•Store or park this machine on a level surface only.
•These machines are designed for level floor operation only. DO NOT OPERATE on ramps or
inclines.
•Battery acid can cause burns. When working on or around batteries, wear protective clothing and
safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of batteries.
•This machine is not suitable for picking up hazardous dust.
•Charging batteries generates explosive gases. DO NOT CHARGE BATTERIES WHEN OPEN
FLAMES OR SPARKS ARE PRESENT. DO NOT SMOKE. Make sure the charger is turned off
before disconnecting it from the batteries. Charge the batteries in a well-ventilated area.
•Maintenance and repairs must be performed by authorized personnel.
SAVE THESE INSTRUCTIONS

2
ELECTRICAL REQUIREMENTS:
This piece of equipment operates on 36 Volt DC.
BATTERY REQUIREMENTS:
6 x 6V 220AH P/N 956720
6 x 6V 275AH P/N 956740
BATTERY SERVICE AND INSTALLATION:
* Warning: Battery acid can cause burns. When working on or around batteries, wear protective
clothing and safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of batteries.
BATTERY INSTALLATION:
1. Raise tank assembly by raising rear cover and disconnecting vacuum recovery hose, Figure 1.
2. Tilt recovery tank.
3. Install batteries as shown in figure 2.
CHARGING OF BATTERIES:
Charging of batteries generates explosive gases. DO NOT CHARGE BATTERIES WHEN OPEN
FLAMES OR SPARKS ARE PRESENT. DO NOT SMOKE. Make sure the charger is turned off
before disconnecting it from the batteries. Charge the batteries in a well-ventilated area. Fluid levels
should be checked before and after charging and maintained at the proper levels.

3
1. Vacuum recovery hose
2. Solution control lever
3. Hour meter (optional)
4. Circuit breaker for vacuum motor
5. Circuit breaker for brush motor
6. Drain hose recovery tank
7. Drain hose solution tank
8. Drain hose for battery tray
9. Reverse control lever
10. Battery condition gauge
11. Brush pressure switch
12. Power-on Indicator light (raise/lower)
13. Squeegee/transport switch
14. Speed control knob
15. Main power switch
16. Key switch (optional)
17. Forward control lever
18. Brush pressure gauge
AUTO SCRUBBER BRUSH DESCRIPTION
TYPE DESCRIPTION DURABILITY* COLOR COMPARISON RECOMMENDED
TO PADS USE
Bassine Natural Fiber Short DarkBrown Red Light duty
general cleaning,
acid etching
Nylon Nylon Medium Black Tan/Red General cleaning
& scrubbing vinyl
floors, ceramic tile
& concrete floors
Dyna-Scrub Nylon impregnated Long Light Red General scrubbing,
with 500 Grit Blue vinyl tile, ceramic
Silicone Carbide tile, epoxy floors,
Fine Bristle, urethane finish,
Dense Fill uneven concrete floors
Power-Scrub Nylon impregnated Long Rust Red/Blue Moderate aggressive
with 120 Grit Silicon scrubbing, tile floors
Carbide Fine Bristle, concrete floors
Dense Fill
Poly-Grit Nylon impregnated Long Green Brown/Black Aggressive stripping
with 80 Grit and scrubbing, tile
Silicon Carbide floors, unfinished
Coarse Bristle concrete floors
Strata-Grit Nylon impregnated Long Dark Black Heavy duty
with 46 Grit Blue stripping/scrubbing
Silicon Carbide unfinshed
Coarse Bristle concrete
*Durability is dependent on floor surface, chemicals used and proper care.
CONTROL PANEL IDENTIFICATION

4
SQUEEGEE ADJUSTMENTS
The squeegee set-up is pre-adjusted at the factory. Adjustments may be required to get optimum performance for
different floors and conditions.
1. Ensure that the scrubber is on a relatively flat surface. Turn on the main power switch and raise the scrub
head assembly off the floor. Set the squeegee/ vacuum switch to the automatic mode.
2. Turn the speed control knob counter-clockwise to the low speed position. Squeeze the forward control lever to lower
the squeegee (item 1) to the floor. Move the machine one or two feet forward to check the rear squeegee blade (item
8) for uniform deflection to the floor.
3. If uneven deflection or lay is evident, minor adjustments may be necessary to avoid streaking and uneven wear on
the blade.
4. To correct this, loosen the wing jam nut (item 4) in order to adjust the caster height. If the squeegee blade is
deflecting too much, the casters need to be lowered to control the down pressure. Lower the caster by turning the
exposed threaded stem (item 9) on the caster clockwise. Make the adjustment a few turns at a time.
5. Repeat step 2.
6. If the blades are not deflecting enough, raise the caster by turning the stem counter-clockwise to adjust the caster
hieght to allow more down pressure on the squeegee. Repeat Step 2.
7. Make sure that there is an even deflection on the entire length of the rear blade. Adjust the castors and retighten the
wing jam nuts to lockthe caster setting in place.
8. Pitch adjustment is necessary if the outer ends on the squeegee blade does not contact the floor and there is too
much deflection in the middle area or if the outer ends are over deflected and there is no contact in the middle.
9. To adjust pitch, lower the squeegee to the floor. Loosen the lock nut (item 3) in the turnbuckle assembly. Turning
the turnbuckle (item 2) clockwise or counterclockwise controls the forward and backward pitch of the squeegee.
Having the rear blades deflected uniformly along its entire length is the desired setup.
10. Repeat Step 2 until the desired setup is achieved.
11. In certain applications where a non-slotted front wiper blade (item 6) is needed, detach the squeegee assembly by
loosening the wing bolts (item7). Unlock the clamp on the front squeegee to release the straps and flip the blade
over to the non-slotted side. Reattach straps and lock the clamp back in place.
12. You can also easily replace the rear blade by unlatching the latch (item 5) and removing the straps by sliding them
off the assembly.

5
OPERATING INSTRUCTIONS
1. Filling: Fill the solution tank with the desired amount of water and add liquid cleaning solution to
the proper dilution ratio. DO NOT USE powdered cleaning chemicals. Powders are unlikely to
dissolve thoroughly, resulting in clogging the in-line solution filter. This can reduce or stop water
flow to the brush.
2. Close lid.
3. Turn on main power switch (Refer to Page 3 #15).
4. Adjust main speed control #14 to full counter-clockwise position.
5. Lower brush assembly (ref. page 3 #11) using switch. Brushes will not come on until forward #17
or reverse #9 lever are pulled. Brushes will remain on for 3 to 5 seconds after levers are released.
Adjustments to brush pressure can be made by depressing switch #11 and reading brush pressure
gauge #18.
6. Squeegee Control/Vacuum. Switch #13 has two positions one is for transport/ double scrubbing,
when the switch is in this position the squeegee will raise and the vacuum will turn off. With the
switch in automatic mode the squeegee will automatically lower in forward movement of the
machine and vacuum will turn on. When the machine is reversed the squeegee will automatically
raise and the vacuum motor will turn off.
7. Solution Control #2. The solution lever is a mechanical cable that opens the solution valve. This
lever must be moved to the full on position then decrease to desired flow to operate properly.
AUTOMATIC PARKING BRAKE OPERATION (CE Only):
Brake lever located behind left wheel.
Run Mode - Normal operation; Brake lever in down position.
•When the power is turned off the brake is automatically engaged.
•When the power is turned on the brake is automatically disengaged and the drive system is
enabled.
Push Mode - Machine inoperable; Brake lever in up position.
•Brake is manually disengaged.
•Power is shut off to the drive system.
MAINTENANCE:
Daily
1. Clean float assembly & squeegee blades. Vac filter.
2. Recharge batteries (check battery acid levels before and after charging).
Monthly
1. Check wear on squeegee blades.
2. Grease rear wheels.
3. Grease pivot points on brush motor assembly.

6
MAINTENANCE OF MACHINE
VACUUM MOTOR
Motor brushes can be replaced with Brush Set, Part No. 741008. Brushes should be replaced only
once. More than once brush replacement will cause very high current consumption. This undue current
consumption lowers overall machine performance and is not in the best interest of economical machine
use.
CARBON BRUSHES IN DRIVE MOTOR
Inspect these brushes once every 18 months or 720 hours.
The brushes can now be inspected by removing the brush caps near the end of the drive motor.
Examine all four brush lengths; if the back end of a brush is even with the edge of the brush holder or
shorter, the brush must be replaced. Replace with Brush Set, Part No. 744155. When installing new
brushes, also inspect cummutator for pits and/or excessive wear. If it is in poor condition, replace
drive motor with Part No. 744154.
CARBON BRUSHES IN BRUSH DRIVE MOTORS
Inspect these brushes once every six months or 360 hours.
Remove scrub head assembly. Examine brush lengths; if the back end of brush is even with the edge
of the brush holder or shorter, the brush must be replaced. Replace with Part No. 833474. When
installing new brushes, also inspect commutator for pits and/or excessive wear. Replace motor with
Part No. 833379 if commutator is in poor condition.
LUBRICATION
1. Grease casters once every week (two fittings per caster) or 15 hours.
2. Oil all moving parts such as hinges and pressure points once every month or every 60 hours.
SQUEEGEE RUBBERS
When the thick rear squeegee rubber is damaged or worn excessively, it will cause streaking and
poor solution pickup. Extended rubber life and be obtained by reversing it, provided it is not torn or
otherwise damaged.
TANKS
At the end of a day’s work (or work cycle, both the vacuum and solution tanks should be drained and
flushed with warm water.
Once a week or 15 hours the vacuum tank should be cleaned of settled debris. This can be done by
lowering the drain hose and washing out the debris.
BATTERIES (956720, 956740)
Periodically remove batteries from machine. Clean batteries, battery tray, and battery compartment
with a solution of baking soda and water. Check all battery cables and wiring for signs of damage or
wear. Replace as needed. Check battery fluid level each charge. Check electrolyte with hydrometer
every 15 hours.

7
TROUBLE SHOOTING
1. Inefficient scrubbing - floors are smeared in appearance.
Solution: Use proper type and correct amount of detergent. Replace worn or damaged scrub
attachments. Increase force on scrubbing head.
2. Squeegee streaks.
Solution: Check rear squeegee rubber for imbedded objects, clean; reverse, or replace if worn or
damaged. Make sure scrub solution is being fed onto brush properly. Use more scrubbing solution.
Replace well-worn scrubber attachments.
3. Odor development.
Solution: Inspect and clean thoroughly the vacuum tank, solution tank, squeegee, vacuum motor,
vacuum hose. NOTE: Super Staph-Trole 256 disinfectant cleaner can be helpful in reducing odors.
4. Vacuum not picking up.
Solution: Water lift should be 60-65" with fully charged batteries. Check seals around vacuum motor
and hose connections. Check vacuum tank drain hose and plug to insure seal. Check hoses for
holes. Clean out squeegee inlet and check squeegee rubbers for severe wear. Make sure solution is
properly feeding into scrubhead attachments. Clean and/or repair vacuum motor.
5. Charger malfunction.
Solution: Consult maintenance and repair data contained in brochure herewith for detailed information.
In general, make sure charger is put in upright position when charging - this helps keep unit cool. Do
not cover charger when it is in use. Make sure connectors on inlet and outlet cords are not broken.
Check AC input voltage – it should be 110 volts, 120 volts, maximum. Replace faulty fuses, ammeter,
timer, or other components, when necessary.
6. Use cycle too short.
Solution: Check voltage on batteries after full charging; output voltage should be 43-45 volts with
specific gravity at 1.260-1.265. Check battery electrolyte level. Check for loose or corroded battery
leads and connections. Replace batteries that will not hold a charge. Lubricate casters. Reduce
scrubbing pressure. Check brushes on motors, especially on vacuum motor. Replace brushes on
motors when needed. Test charger for output, it may need repair.
7. Motors will not start or run.
Solution: Check battery leads and connection for corrosion and looseness; correct if required. Check
switches for proper contacting; replace if required. Check motor brushes; replace brushes or motors
if required.
8. Speed control does not function.
Solution: The speed control has built-in protection to guard against reversed connections, check
battery connections. Machine locked in high or low speed. Inspect entire speed control for burn
marks of components that have broken. These would be caused by a direct short in the circuit.
Replace entire control as needed.

8

9
Parts List
Item Part No. Qty. Description
1 320122 1 Console Machined
2 320730 1 Mainframe PowerBoss 32/38
3 320300PB 1 Solution Tank Assembly
4 320200 1 Recovery Tank Assembly
5 320146B 1 Recovery Lid Burgundy
6 320220 1 Vacuum Hose Long
7 260203 1 Wire Grip Hose Clamp
8 320222 1 Gasket
9 320178 1 Water Shut-Off Plate
10 712540 7 SCR-MC 10-24 x .37 SS TH
11 712102 2 Bolt-Shoulder 1/2-20 x 1.50
12 711161 11 SCR-Hi/Lo 10 x 5/8
13 260170 2 Retainer Flap
14 760263 2 Foam Tape 16.50”
15 320239 2 Lid Gasket Long
16 260157 2 Lid Gasket Short
17 320145 1 Recovery Tank Hinge
18 320144 1 Backing Strap
19 450090 1 Recovery Hose Assembly
20 320208 1 Retaining Hook
21 260087 1 Hinge
22 712086 1 5/16 Wire Eyebolt
23 320283 2 Skirt Retainer
24 320284 2 Rubber Skirt
25 320280 1 Shroud Weldment - Left Side
26 340664 2 Latch
27 260192 2 Sleeve
28
29 715619 1 Warning Decal
30 320279 1 Shroud Weldment - Right Side
31 380215 2 Roller Pin
32 711811 2 Hitch Pin, Cotterless
33 66-436-A 2 Roller Wheel
34 712822 10 SCR-MC 10-24 x .50 SS
35 715628 1 Battery Decal
36 712810 8 SCR-MC 10-32 x 3/8
37 711350 8 Nut-Nyloc 10-32
38 712565 20 SCR-MC 1/4-20 x .75 SS
39
40 711504 6 WSR-Flat 1/4 SS
41 712667 4 Nut-Nyloc 1/4-20
42 710196 5 SCR-MC 5/16-18 x .75 ST PL
43 711545 6 WSR-Helical 5/16
44 711506 6 WSR-Flat 5/16 STPL
45 320244 1 Lid Flap
46 711379 1 Nut-Flanged Wizz 5/16-18
47 260216 1 Screen Filter
48 260294 1 Gasket 2.0 x 4.0 x .125
49 711202 12 Bolt-HH 1/4-20 x .50
50
51 711715 4 Retaining Ring Ext .75
52 320275 1 Side Plate Weldment - Left
53 320276 1 Side Plate Weldment - Right
54 711544 12 WSR-Helical 1/4

10
320200
RECOVERY TANK ASSEMBLY
Item Part No. Qty. Description
1 260156 1 Foam Float Assembly
2 320121 1 Recovery Tank
3 828970 1 WSR-Neop 1.81 x 2.37
4 450081 1 WSR-SS 1.908 x 2.41 x .03
5 760220MCH 1 1.5 Adaptor Gray
6 260203 1 Hose Clamp Wire Grip
7 833316 1 Drain Plug 1 1/4
8 260202 1 Drain Hose Assembly
9 320206 1 Lift Cable Ass’y
10 712575 1 5/16-18 x .75 HH SS
11 711506 1 WSR-Flat 5/16
12 715620 1 Decal “Maintenance Schedule”
13 320009 1 Backing Angle
14 712563 5 SCR-MC 1/4-20 x 1.00 FH
15 320269 1 Strap, Drain Plug Retaining

11
320300PB
SOLUTION TANK ASSEMBLY
Item Part No. Qty. Description
1 260029 1 Solution Lid
2 320120 1 Solution Tank
3 450021 1 Hinge
4 712764 7 WSR-SS #10
5
6 712540 7 SCR-MC 10-24 x .37 SS TH
7 832949 2 Bracket - Bumper
8
9 832896 2 Guide Wheel
10 833254 2 Bumper Wheel Axle
11 710985 2 SCR-SC 3/8-16 x .62
12 710353 2 SCR-MC 10-32 x .37
13 711553 2 WSR-Internal Lock 10
14 130118 1 Solution Strainer M3-40
15 210409 1 Adapter Brass 3/8 FPT x 3/8 MPT
16 210414 1 O-Ring
17 711513 1 WSR-Flat .69 x 1.06 x .03 SS
18 700028 1 Fitting Brass 90 3/8FPT
19 320265 1 3/8 Dubl-Barb x 3/8 MPT
20 450076 1 Crimp Clamp SS 185R
21 712575 1 5/16-18 x .75 HH SS
22 711506 1 WSR-Flat 5/16
23 320252 1 Hose, Solution Tank
24 320246 1 Solution Tank Cable Assembly

12

13
Parts List
Item Part No. Qty. Description
1 260041 2 1/2” Oilite Bushing
2 711579 10 WSR-Flat .56 x 1.00 x .100
3 320732 1 Link, Brush Press, Adj.
4 320174 1 Switch Bracket
5 320175 1 Bracket Arm
6 320213 1 Splash Guard
7 320214 1 Retainer Strap
8 320236 1 Vacuum Pipe Weldment
9 320450 1 Squeegee Mech. Asm. Comp.
10 320730 1 Mainframe Weldment
11 320705 2 Transaxle Bracket, Lower
12 320735 1 Lift Weldment
13 320731 2 Wheel 10 x 2.75, 3 Bolt
14 320750 1 Scrubhead Assembly Complete
15 380-532-20 3 Cotter Key
16 670070 6 Acorn Nut 1/2-20
17 710180 2 SCR-MC 1/4-20 x .75
18 711202 2 BLT-HH 1/4-20 x .50
19 711203 10 BLT-HH 1/4-20 x 5/8
20 711206 2 BLT-HH 1/4-20 x 3/4
21 711228 8 BLT-HH 5/16-18 x .75
22 320733 2 Link, Spring Adjuster
23 711373 1 Nut-Nyloc 1/4-20
24 711425 2 Nut-Flanged Wizz 1/4-20
25 711427 2 Nut-Flanged Wizz 10-24
26 711509 6 WSR-Flat 1/2
27 711515 12 WSR-Flat .38 x .82 x .05
28 711544 16 WSR-Helical 1/4
29 711545 12 WSR-Helical 5/16
30 711546 4 WSR-Helical 3/8
31 711594 2 WSR-Flat .56 x .88 x .03
32 711669 1 Clevis Pin 1/2 x 2.25
33 711672 2 Clevis Pin 1/2 x 2
34 712108 3 Clevis Pin 1/2 x 1.25
35 712109 1 Clevis Pin 1/2 x .1.75
36 712310 4 WSR-Flat .52 x .87 x .06
37 712574 1 BLT-SS Carr 1/4-20 x 3.00
38 712680 4 5/16-18 Nut SS
39 713042 4 BLT-HH 3/8-16 x 1.00 #5
40 740132 2 Insulator
41 740802 1 Actuator
42 744151 1 Transaxle 18” 36V
43 744151-1 1 Brake, 320 Trans CE Only
44 809236 2 1 Oilite Flanged Bushing
45 809237 2 Retaining Ring
46 809311 4 Cotter Pin
47 827110 2 Caster
48 320711 1 Transaxle Cover
49 320712 1 Splash Guard
50 710178 4 SCR-MC 1/4-20 x .50 STPL
51 712534 4 SCR-MC 10-24 x .50 SS
52 320408 2 Spring, Extension

14

15
Parts List
Item Part No. Qty. Description
1 320215 1 Battery Tray Liner
2 320118 1 Battery Tray
3 840011 1 Vac Motor Cover, Top
4 840012 1 Vac Motor Cover, Bottom
4A 840012CTD 1 Vac Motor Cover, Bottom (CE)
5 380064 1 Foam Ring
6 740228 1 Vac Motor 36V 3-Stage
7 290017 1 Molded Gasket
8 320119 1 Vac Motor Platform
9 320185 1 Exhaust Manifold Weldment
10 833191 1 Hose Rubber Flex 2 x 9
11 320216 1 Hose Rubber Flex 2 x 20
12 829067 4 Crimp Clamp
13 833265PLT 3 Stand-Off 1/4-20
14 809412 1 Gasket Support
15 320241 1 Vacuum Hose Short
16 828975 1 WSR-Neop .75 x 1.5 x .09
17 320265 2 3/8 Dubl-Barb x 3/8 MPT
18 742001 1 Wire Harness
19 430120 1 U-Channel
20 260181 1 Drain Hose 1/2 x 18
21 450076 9 Crimp Clamp SS 185R
22 420009 1 Hose Fitting (Male Elbow)
23 430114 1 Nylon Cap 1/4 FPT HC4
24 210408 1 3/8 Brass Tee
25 420065 1 Hose Fitting (Female Elbow)
26 711124 2 SCR-ST 10 x .38 NI
27 828952 3 3/8 Barb x 1/4 MPT
28 712760 4 WSR-Flat .56 x 1.00 SS
29 210370 1 Solution Valve Bracket
30
31 320253 2 Valve Solution Hose
32 809413MCH 1 Solution Valve
33 210045 1 Solution Control Cable
34 711124 1 SCR-ST-B 10 x .37 NI
35 711512 1 WSR-Flat .75 x 1.37 x .08
36 320218 1 Clear Hose, Dump
37 320252 1 Wire Hose, Supply
38 712086 2 5/16 Wire Eyebolt
39 830708 1 Reducer 3/8 x 1/4
40 320272 2 Nut-PLS 1/4 NPT
41 712565 2 SCR-MC 1/4-20 x .63 SS
42 711517 1 WSR-Flat .77 x 1.37 X .03
43 762073 3 Spacer
44 711106 3 SCR-ST-A 10 x .75
45 260203 2 Hose Clamp Wire Grip
46 712667 7 Nut Nyloc 1/4-20 SS
47 711128 1 SCR-ST 8 x .63
48 832996 1 Terminal Block
49 712638 3 Nut-Hex 10-24 SS Nyloc
50 712537 3 SCR-MC 10-24 x .75 SS TH
51 711505 4 WSR-Flat 1/4
52 72-416-10 2 SCR-TF 1/4-20
53 831306 1 Street 90° 1/4 x 1/4
54 320271 1 90° Nozzle Fitting
55 809444 1 Clip Cord
56 712026 1 1/4 Wire Eyebolt
57 320246 1 Solution Tank Cable
58 420011 2 Sleeve Insert
59 740494 1 Water Valve 36VDC
60 712565 2 SCR-MC 1/4-20 x .62 SS
61 711504 2 WSR-Flat 1/4 ID SS
62 320264 1 3/8 Dubl-Barb x 1/4 MPF
63 260224 1 Drain Hose 1/2 x 18 Silicone
64 320273 1 Hose Shut-Off Clamp

16

17
Parts List
Item Part No. Qty. Description
1 210045 1 Cable Solution Control
2 210413 2 Return Springs
3 260066 4 3/8 Oilite Flanged Bushing
4 260069MCH 1 Left Handle
5 260070MCH 1 Right Handle
6 260274 2 Rubber Grommet
7 260255 1 Speed Control Bracket
7CE 260255CE 1 Speed Control Bracket, CE
8 320147 1 Switch Actuator Weldment
9 320161 1 Clevis, Squeegee Cable
10 320012 1 Linear Actuator - Squeegee
11 320176 1 Back Panel
12 320187 1 Dual Switch Bracket
13 320202CESP 1 Dashboard CE Screen Printed
14 320203 1 Battery Gauge Bracket
15 320207 1 Circuit Breaker Face Plate
16 320211 1 Cable, Squeegee Cable
17 320011 1 Actuator Support
18 320247 1 Terminal Blcok Bracket, CE
19 320297 1 Squeegee Assembly Complete
20 320706 1 Lever Mounting Bracket
21 320726 1 Electrical Panel
22 710178 6 SCR-MC 1/4-20 x .50
23 710180 15 SCR-MC 1/4-20 x .75
24 710207 2 SCR-MC 6-32 x 1.0
25 711104 1 SCR-ST-A 10 x .50, CE
26 711125 2 SCR-ST-B 10 x .50
27 711161 14 SCR-Hi/Lo 10 x .75
28 710383 1 SCR-MC 1/4-20 x 1.25
29 711368 3 Wing Nut 1/4-20
30 711372 2 Nut-Nyloc 8-32
31 711420 2 Nut-Hex Jam 5/16-18
32 711430 1 Tinnerman Clip
33 711503 2 WSR-Flat 10
34 711505 3 WSR-Flat 1/4
35 711515 2 WSR-Flat .38 x .82 x .05
36 711523 2 WSR-Wave .38 x .68 x .01
37 711544 3 WSR-Helical 1/4
38 711575 1 WSR-Flat .312 x .75
39 711579 2 WSR-Flat .56 x 1.00
40 711668 1 Clevis Pin 3/8 x 1.0
41 711671 1 Clevis Pin .306 x 2.125
42 711720 4 Retaining Ring E Ext. .25
43 711808 1 Cotter Pin
44 712088 1 SCR-Hi/Lo 8-18 x .75, CE
45 712100 2 Bolt-Shoulder 3/8 x 2.25
46 712320 2 WSR-Nylon .22 x .45 x .04
Item Part No. Qty. Description
47 712536 2 SCR-MC 10-24 x .62 STPL
48 712540 6 SCR-MC 10-24 x .37 TH
49 712638 1 Nut-Hex 10-24 SS Nyloc
50 712764 1 WSR-SS #10
51 712822 12 SCR-MC 10-24 x .50 TH
52 715604 1 Decal Solution
53 715608 1 Forward Decal
54
55 715611 1 Reverse Decal
56 715617 1 Circuit Breaker Decal
57 740036 1 Terminal Block, CE
58 740132 3 Insulator Glastic
59 740134-1 1 Shunt w/o Wires
60 740135 1 Meter, 100A DC - Pressure
61 740136 1 Battery Condition
62 740147 1 Connector
63 740242 1 Contactor 36V
64 740243 2 Solenoid 36V
65 740247 1 30 amp Circuit Breaker
66 740368 1 Potentiometer Assembly
67 740800CE 1 Rocker Switch Momentary CE
68 740801CE 1 Rocker Switch CE
69 740803-1 1 Speed Control 36V
70 741005 1 Key Switch (optional)
71 742010 1 Indicator Light, 36VDC
72 742266 1 60 amp Circuit Breaker
73 760286 1 Wire Formed Hook
74 200340 2 Spacer
75 740811 1 Switch Boot, CE
76 805637 1 SCR Insulator
77 809311 4 Cotter Pin 7/64 x 1.0
78 809754 1 Rocker Switch
78A 740711CE 1 Rocker Switch, CE
79 809874 1 Knob
80 827060 2 Forward/Reverse Switches
81 832015 2 Spacer
82 833277PLT 2 Actuator Bush Plated
83 833286PLT 2 Actuator Bush Plated
84 833294 2 Actuator Pin
85 833329SA 1 Switch, Staggered Action
86 833638 3 Brass Stud
87 833823 1 2” Hole Plug
88 833824 1 S.S. Washer 2 x 2.43 x .035
89 881002 3 Clevis Pin 5/16 x 1.00
90 260210 1 Moisture Guard for Item 69
91 320248 1 Clevis, Slotted
92 710385 1 SCR-MC 1/4-20 x 1.50