Minuteman Pro 2200r User manual


Uninterruptible Power Supply
User’s Manual


1
Pro Series User’s Manual
1. Introduction 2
2. Controls and Indicators 4
3. Installation 6
4. Operation 8
5. Troubleshooting 9
6. Replacing the Battery 10
7. Obtaining Service 13
8. Specifications 14
9. Configurable Parameters & Settings 15
10. Limited Warranty 16
Copyright Para Systems, Inc., 1998

2
Thank you for purchasing a Minuteman power protection product. It has been designed and
manufactured to provide many years of trouble free service.
Please read the manual before installing your Pro Series UPS as it
provides the information that should be followed during installation and
maintenance of the UPS and batteries allowing you to correctly set up
your system for the maximum safety and performance.
Included is information on customer support and factory service if it is required. If you
experience a problem with the UPS, please refer to the Troubleshooting guide in this
manual to correct the problem or collect enough information so that the Minuteman
technical support department can rapidly assist you.
WARNING: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS !
NOTICE: This equipment has been tested and found to comply with
the limits for a Class A digital device, persuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause interference to radio communications. Operation of this
equipment in a residential area is likelly to cause harmful interference, in
which case the user will be required to correct the interference at his own
expense.
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus set out in the Radio interference
regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emit pas de bruits radioélectriques
dépassant les limites applicables aus appareils numérique de las Class A
prescrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministèredès Communications du Canada.

3
Receiving Inspection
After removing your Minuteman UPS from its carton, it should be inspected for damage that
may have occurred in shipping. Immediately notify the carrier and place of purchase if any
damage is found. Warranty claims for damage caused by the carrier will not be honored.
The packing materials that your UPS was shipped in are carefully designed to minimize any
shipping damage. In the unlikely case that the UPS needs to be returned to Minuteman,
please use the original packing material. Since Minuteman is not responsible for shipping
damage incurred when the system is returned, the original packing material is inexpensive
insurance.
PLEASE SAVE THE PACKING MATERIALS!
TO DE-ENERGIZE THE OUTPUTS OF THE UPS:
1. IF THE UPS IS ON PRESS THE ON/OFF BUTTON FOR 1 SECOND.
2. DISCONNECT THE UPS FROM THE AC POWER OUTLET.
3. TO DE-ENERGIZE THE UPS COMPLETELY, DISCONNECT THE
BATTERY. (SEE SECTION 6 FOR INSTRUCTIONS)
Para Systems Life Support Policy
                     
                   
                   
                    
           !     "    
             #    
$            "     
              
             
                %&  
'  ()
*               + ,-$. '  +
,-$.              * /  + ,-$.  
 " -       #      
CAUTION! TO REDUCE THE RISK OF ELECTRICAL SHOCK IN
CONDITIONS WHERE LOAD EQUIPMENT GROUNDING CANNOT BE
VERIFIED, DISCONNECT THE UPS FROM THE AC POWER OUTLET
BEFORE INSTALLING A COMPUTER INTERFACE CABLE. RECONNECT
THE POWER CORD ONLY AFTER ALL SIGNALING CONNECTIONS ARE
MADE.
CAUTION! CONNECT THE UPS TO A TWO POLE, THREE WIRE
GROUNDING AC POWER OUTLET. THE RECEPTACLE MUST BE
CONNECTED TO APPROPRIATE BRANCH PROTECTION (CIRCUIT
BREAKER OR FUSE). CONNECTION TO ANY OTHER TYPE OF
RECEPTACLE MAY RESULT IN A SHOCK HAZARD AND VIOLATE LOCAL
ELECTRICAL CODES.
WARNING:RISK OF ELECTRICAL SHOCK. HAZARDOUS LIVE PARTS
INSIDE THIS POWER SUPPLY ARE ENERGIZED FROM THE BATTERY
EVEN WHEN THE AC INPUT POWER IS DISCONNECTED.

4
FRONT PANEL
The online/on battery/boost and buck LED illuminates in a steady state when the UPS is on
and supplying AC power to the load, blinks (5 times per second) and sounds the audible
alarm when supplying battery power to the load, blinks (once per second) with no audible
alarm when the automatic voltage regulator is in operation.
TEST
Pro 700, 1000, 1400r
front panel Pro 2200r front panel
online on-battery
boost and buck
The fault LED illuminates when the UPS has detected an internal fault (contact
Minuteman technical support).
Press and release the TEST/Alarm silence button to test the UPS
or silence the alarm.(see section 4)
The overload LED illuminates when the loads connected to the UPS exceeds
the UPS power rating (see section 4).
The replace battery LED illuminates when the UPS has detected that battery
replacement is required (see section 6).
Press and release the ON/OFF button after one beep to turn the unit on or off.
(see section 4)

5
REAR PANEL
The Accessory Slot is used for SNMP UPS monitoring, power control, multiple server
support, and special signaling (see section 3).
The DB9 connector is used for UPS monitoring and control through a computer’s serial
port (see section 3).
The RJ-45/RJ-11 modular connectors are used for 10 Base-T network/single line telephone
surge protection (see section 3).
The Option slots are for adding extra RJ-45/RJ-11 surge protection cards. Available from
Minuteman.
The Site Wiring Fault LED illuminates when the UPS detects an improperly wired AC
power outlet (only available on 115V models).
The Output Power receptacles are NEMA 5-15R type (IEC output sockets on 230Vac
models).
The Input Power cord has a NEMA 5-15P connector (IEC input socket on 230Vac models,
L5-30P for Pro 2200r 115V model).
The Input Circuit Breaker will trip in the event the load exceeds the UPS’s power rating.
The Output Circuit Breakers will trip in the event the load exceeds the UPS’s power rating
(2200 115V model only).
The External Battery
connector is for adding more battery capacity to the UPS (see section 3).
Pro 700, 1000 and 1400r
Rear Panel
Pro 2200r Rear Panel
Accessory Slot
Accessory Slot
DB9
Connector
RJ-45/RJ-11
Protection
In
p
ut Power
Site Wiring Fault
Output Receptacles
Input Circuit
Breaker
Output Receptacles
DB9 Connector
Input Circuit
Breaker
RJ-45/RJ-11
Protection
Input Power Output Circuit
Breaker
External Battery
Connector
Option SlotSite Wiring Fault
O
p
tion Slots

6
INSTALLATION PLACEMENT
Please observe the following items;
The UPS comes with standard 19” (46.5 cm) rack mount brackets installed. These
brackets are reversible for mounting to a standard 23” (59.2 cm) rack.
Screws are not supplied with the UPS for attaching it to the rack (for screw size varies
according to rack size).
Install the UPS in a temperature controlled, indoor environment that is free of
conductive contaminants. Select a location which will provide good air circulation for the
UPS at all times. Avoid locations near heating devices, water or excessive humidity, or
where the UPS is exposed to direct sunlight. Select a location sturdy enough to handle the
weight of the UPS.
Two additional sets of bracket holes are located on the sides of the UPS to allow for
the UPS to be mounted with a different set back. After moving the bracket to these holes,
make sure the rack will not tip.
After mounting is complete, plug the UPS in to a two pole, three wire, grounded
receptacle. Route power cords so they cannot be walked on or damaged.
WARNING: Care should be taken when installing the units due to their
weight. Use two or more people when installing. Do not move the rack after
the UPS is installed (the position of the UPS’s weight may cause the rack to
be unstable during movement).
ACCESSORY SLOT (OPTIONAL)
This slot is used for optional accessories available from Minuteman. Call for more
information.
DB9 CONNECTOR
Minuteman Power Management software and interface cables kits are used with this port
(software and cables are optional and available from Minuteman). Use only Minuteman or
Minuteman approved interface cables with these UPS’s. Connect the interface cable to the
DB9 connector on the rear of the UPS. Secure the connector to the UPS via the screws on
the connector housing. Connect the other end of the cable to the device that will be
monitoring/controlling the UPS.
NOTE: CONNECTING TO THE DB9 IS OPTIONAL. THE UPS WORKS PROPERLY
WITHOUT A CONNECTION.

7
RJ-45/RJ-11 PROTECTION
Connect a single line telephone or a 10 Base-T network line to the protection sockets on
the rear of the UPS. This connection will require another length of telephone or network
cable. The cable coming from the telephone service or networked system is connected to
the port marked “IN”. The port marked “OUT” is connected to the equipment to be
protected.
NOTE: CONNECTING TO THIS PORT IS OPTIONAL. THE UPS WORKS
PROPERLY WITHOUT A CONNECTION.
SITE WIRING FAULT (115V models only)
After plugging in the UPS, check the site wiring fault (SWF) LED on the rear of the unit. If
the LED is illuminated, the UPS is plugged into an improperly wired AC outlet.
CAUTION!: IF THE UPS INDICATES A SITE WIRING FAULT, HAVE A
QUALIFIED ELECTRICAN CORRECT THE PROBLEM.
EXTERNAL BATTERY CONNECTOR
This is an option that is only available on the 2200VA UPS. This is an optional connection
for this UPS. The 2200 has internal batteries. The battery pack is available from Minuteman
(PRO BP1). Only one battery pack may be connected to the UPS to extend its runtime. Use
only the Pro BP1 battery pack with this UPS. The use of any other battery pack may
damage the UPS and void the warranty.
CHARGING THE BATTERIES
The PRO Series UPS’s will charge the batteries whenever the unit is connected to an AC
source. It is recommended that the UPS batteries be charged for a minimum of 4 hours
before use. The UPS may be used immediately. However, the “on battery” run time may be
less than normally expected.
CONNECTING YOUR EQUIPMENT
Plug the equipment into the receptacles on the rear of the unit. Insure that you do not
exceed the maximum output rating of the UPS (refer to the back panel of the UPS or the
electrical specifications in this manual).
CAUTION! DO NOT CONNECT A LASER PRINTER TO THE UPS
UNLESS THE UPS IS RATED 2000VA OR GREATER. A LASER PRINTER
DRAWS SIGNIFICANTLY MORE POWER WHEN PRINTING THAN AT
IDLE AND MAY OVERLOAD THE UPS.

8
TURNING THE UNIT ON/OFF
ON/OFF SWITCH
Press and release the ON/OFF switch after one beep to turn the unit on and supply power
to the load. The load will be immediately powered and 2 seconds later the UPS will run a
15 second self test before returning the load to the AC line. Press and release the switch
again to turn the UPS off. The UPS will continue to charge the batteries whenever it is
plugged in and AC line is present.
SELF TEST
TEST SWITCH
The self test feature is useful to verify the correct operation of the UPS and the condition of
the battery. With the UPS plugged into normal AC, press and release the TEST/Alarm
silence switch to initiate a self test. When the UPS is in battery mode, press and release
the TEST/Alarm silence switch to silence the alarm.
NOTE: The UPS will automatically perform a self test on startup and every two
weeks.
During the self test the UPS will switch to battery power and the on-line LED will blink and
the audible alarm will sound as well. This test will run for approximately fifteen seconds to
measure the battery’s capability to provide an acceptable amount of runtime. If the UPS
fails a self test, one of the LED’s will remain illuminated indicating the type of problem (see
section 5 Troubleshooting).
ALARMS
ON BATTERY
When the UPS is operating on the batteries, the on-line LED will blink and the audible
alarm will sound every 10 seconds. The alarm will stop once the UPS returns to on-line
operation.
UPS FAULT
When the UPS detects a hardware fault, the fault LED will illuminate and the UPS will emit
a sustained tone. The fault condition can be re-set by turning the UPS off and then on or by
pressing the test switch (see section 5 for more information).
OVERLOAD
When the amount of load attached to the UPS exceeds its power rating, the overload LED
will illuminate and the UPS will emit a sustained tone. This alarm will remain on until the
excess load is removed or the UPS’s self protection circuit shuts the UPS down.
TEST

9
REPLACE BATTERY
The UPS automatically tests the battery’s condition and will illuminate the replace battery
LED and emit a short beep. This tone will be repeated every hour until the battery passes a
self test. It is recommended that the UPS be allowed to charge overnight before performing
a battery test to confirm a replace battery condition.
LOW BATTERY WARNING
The UPS will emit a steady tone when the battery reserve runs low. It continues to emit the
steady tone until AC returns or the UPS shuts down from battery exhaustion.
TROUBLESHOOTING CHART
Symptom Possible Cause What To Do
UPS will not turn on On/Off button not pushed Press On button
momentarily (one beep) to
start UPS
UPS operates in battery
mode only, even though
there is normal AC present
Input AC breaker is tripped Reset circuit breaker by
pressing the plunger back
in. Circuit breaker trips
after UPS starts up, reduce
the load on the UPS
Fault LED is illuminated UPS has detected an
internal fault Call for service
The Site Wiring Fault LED
is illuminated Incorrect service wiring Have a qualified electrician correct the service wiring
The Online/On Battery LED
is illuminated, but there is
no output
The UPS is being
controlled via its
communications port
Disconnect the
communications cable
from the UPS and press
the On button
momentarily. If the UPS
works normally, software
has control of the UPS
UPS does not provide
expected backup time The batteries may be weak or at the end of useful
service life
Charge the batteries for 8
hours and retest. If the
backup time is still less
than expected, the
batteries may need to be
replaced, even though the
Replace Battery LED is not
illuminated
Replace Battery LED is
illuminated Weak or bad batteries, or bad battery connection Check the battery connection and/or replace
the batteries. Follow
battery replacement
procedures in Section 6
The UPS occasionally
emits a beep Normal operation The UPS is performing its intended function

10
REPLACING THE BATTERY
The PRO Series UPS has an easy to replace hot-swappable batteries. Please read the
following warning statements before attempting to service the batteries.
CAUTION: DO NOT OPEN OR MUTILATE BATTERIES. RELEASED
ELECTROLYTE IS HARMFUL TO THE SKIN AND EYES AND MAY BE TOXIC
CAUTION: DO NOT DISPOSE OF BATTERIES IN A FIRE. THE BATTERIES MAY
EXPLODE.
CAUTION: REPLACE BATTERIES WITH THE SAME NUMBER AND TYPE AS
ORIGINALLY INSTALLED IN THE UPS. THESE BATTERIES HAVE PRESSURE
OPERATED VENTS.
WARNING! THIS UNINTERRUPTIBLE POWER SOURCE CONTAINS
POTENTIALLY HAZARDOUS VOLTAGES. DO NOT ATTEMPT TO
DISASSEMBLE THE UNIT BEYOND BATTERY REPLACEMENT
PROCEDURES BELOW. EXCEPT FOR THE BATTERY, THIS UPS
CONTAINS NO USER SERVICABLE PARTS. REPAIRS CAN BE
PERFORMED BY MINUTEMAN SERVICE PERSONNEL ONLY.
THE BATTERIES IN THIS UPS ARE RECYCLABLE. DISPOSE OF THE
BATTERIES PROPERLY. THE BATTERIES CONTAIN LEAD AND POSE A
HAZARD TO THE ENVIRONMENT AND HUMAN HEALTH IF NOT
DISPOSED OF PROPERLY. REFER TO LOCAL CODES FOR PROPER
DISPOSAL REQUIREMENTS OR RETURN THE BATTERY TO
MINUTEMAN.
CAUTION: ALTHOUGH BATTERY SYSTEM VOLTAGES ARE ONLY
24 VDC AND 48 VDC, THE BATTERY SYSTEM CAN STILL PRESENT A
RISK. THE CURRENT CAPABILITY OF A BATTERY IS SUFFICENT TO
BURN WIRE OR TOOLS VERY RAPIDLY, PRODUCING MOLTEN METAL.
OBSERVE THESE PRECAUTIONS WHEN REPLACING THE BATTERIES:
1. REMOVE WATCHES, RINGS, OR OTHER METAL OBJECTS;
2. USE HAND TOOLS WITH INSULATED HANDLES;
3. DO NOT LAY TOOLS OR OTHER METAL PARTS ON TOP OF
BATTERIES
CAUTION: WHEN DISCONNECTING THE INTERNAL BATTERIES
OR THE EXTERNAL BATTERY PACK, THE UPS CANNOT BE RUNNING
IN THE BATTERY MODE. THE UPS MUST BE OFF OR SUPPLYING
POWER TO THE LOAD FROM THE UTILITY MAINS.

11
BATTERY REPLACEMENT PROCEDURE
PLEASE READ THE PREVIOUS “CAUTIONS” SECTION BEFORE
ATTEMPTING TO REPLACE THE BATTERIES
Battery replacement is a safe procedure when cautions and instructions are carefully
followed. You may leave the UPS and the loads on for the following procedure.
700, 1000 and 1400VA Models
1. Reach into the finger pull on the front of the UPS and open the front cover. Swing the
cover open as shown and remove.
2. Use a screwdriver to remove the battery door screws and open the door.
3. Disconnect the battery leads in the following order. Red wire first. Yellow jumper wire
second and Black wire last. Loosen the connectors by gently wiggling them while
pulling to the right of the battery connector. NOTE: Note the connections between the
batteries, so proper connections are made when installing the new batteries.
4. Grasp the battery tabs in numerical order and gently pull each battery out one at a
time. For models with four batteries, repeat step 3 for the rear batteries. NOTE: The
red and black wire will need to be moved to the right side of the opening so the left
battery can be removed and to the left side of the opening so the right battery can be
removed. NOTE: Be careful when removing the batteries since they are heavy.
5. Install the new batteries by placing the right battery in first followed by the left
(reversing the order from which they were removed). As in step 4, the red and black
wire will need to be moved to the left side of the opening so the right battery can be
installed and to the right side of the opening so the left battery can be installed.
Connect the battery leads to the new battery as shown in the following order.
Connect the BLACK wire to the negative (-) terminal first. Then connect the Yellow
jumper wire between the batteries. The RED wire is the last connection. Connect the
RED wire to the positive (+) terminal.
NOTE: Small sparks at the battery connection are normal during battery connection. Close
the door, replace the battery compartment screws, and replace the front cover.
6. Dispose of the battery at an appropriate recycling facility or return it to Minuteman in
the packing material from the new battery kit.
2200VA Model
Step 3
Step 1 Step 2
Step 4

12
1. Reach into the finger pull on the front of the UPS and open the front cover. Swing the
cover open as shown and remove.
2. Use a screwdriver to remove the battery door screws and open the door.
3. Disconnect the battery leads in the following order. Red wire first. Black wire second
and the Yellow jumper wires last. Loosen the connectors by gently wiggling them
while pulling straight back from the battery connector. NOTE: Note the connections
between the batteries, so proper connections are made when installing the new
batteries.
4. Grasp the battery tabs in numerical order and gently pull each battery out one at a
time. After the front batteries are removed, grasp the two remaining battery tabs and
pull the rear batteries out together. NOTE: Be careful when removing the batteries
since they are heavy.
5. Remove the Yellow jumpers from the old batteries and install them on the new
batteries.
6. Install the new batteries in reverse order of removal. When making the final wire
connection, connect the Yellow jumper wires first.Then connect the BLACK wire to
the negative (-) terminal. The RED wire is the last connection. Connect the RED wire
to the positive (+) terminal. NOTE: Small sparks at the battery connection are normal
during battery connection. Close the door, replace the battery compartment screws,
and replace the front cover.
7. Dispose of the battery at an appropriate recycling facility or return it to Minuteman in
the packing material from the new battery kit.
Step 4
Step 1 Step 2 Step 3

13
IF THE UPS REQUIRES SERVICE
1. Use the TROUBLESHOOTING section 5 to eliminate obvious causes.
2. Verify that no circuit breakers are tripped. A tripped circuit breaker is the most
common problem.
3. Call your dealer for assistance. If you cannot reach your dealer, or if he cannot resolve
the problem. call or FAX Minuteman Technical Support at the following numbers:
Voice phone [phone], FAX line [phone], e-mail: support@minuteman-
ups.com. Please have the following information available BEFORE calling technical
support.
A. Your Name and address.
B. Where and when the unit was purchased.
C. All of the model information on the rear of your Pro Series UPS.
D. Any information on the failure, including LEDs that may be illuminated.
E. A description of the protected equipment, including model numbers if possible.
F. A technician will ask you for the above information and, if possible, help solve
your problem over the phone. In the event that the unit requires factory service,
the technician will issue you a Return Material Authorization Number (RMA #).
G. If the UPS is under warranty, the repairs will be done at no charge. If not, there
will be a charge for repair.
4. Pack the UPS in its original packaging. If the original packaging is no longer available,
ask the technical support technician about obtaining a new set. It is important to pack
the UPS properly in order to avoid damage in transit. Never use Styrofoam beads for a
packing material. Include a letter with your name, address, day time phone number,
RMA number, a copy of your original sales receipt, and a brief description of the
trouble.
5. Mark the RMA # on the outside of all packages. The factory cannot accept any
package without the RMA # marked on the outside.
6. Return the UPS by insured, prepaid carrier to:
Minuteman, Para Systems Inc.
1455 LeMay Drive
Carrollton, Tx. 75007

14
NOTE: 230V Specs Shown in ( )
Pro 700r Pro 1000r Pro 1400r Pro 2200r
Nominal input voltage 115V (230V) 115V (230V) 115V (230V) 115V (230V)
*Acceptable input voltage 92-150 (176-282) 92-150 (176-282) 92-150 (176-282) 92-150 (176-282)
*Output voltage (on-line
operation) 103V-131V (196V-253V) 103V-131V (196V-253V) 103V-131V (196V-253V) 103V-131V (196V-253V)
Output voltage (Battery
operation) Nominal voltage ±5%, -10% after low battery warning.
Simulated sine wave
Nominal input frequency 50 or 60Hz, autosensing
Frequency limits(on-line) 50 or 60 Hz +/- 3 Hz
Frequency (Battery operation) 50 or 60 Hz +/- 1 Hz
Input protection Resettable circuit breaker
Transfer time 4 ms typical
Maximum load VA/Watts 700VA/450W 1000VA/670W 1400VA/950W 2200VA/1600W
Protection Overcurrent and short-circuit protected, latching shutdown on overload
Surge energy rating(one time,
10 to 1000 us waveform) 480 Joules
Surge current capability (one
time, 8 to 20 us waveform) 6500 A maximum
Surge response time 0 ns (instantaneous) normal mode, <5ns common mode
Surge voltage let-through < 0.3 % of peak, typical
Noise filter Normal and common mode EMI/RFI suppression, 100 kHz to 10 MHz
Battery Type Hot-swappable, Spill-proof, sealed lead acid, maintenance-free
Typical battery life 3 to 5 years
Typical recharge time 4 hours
10 Base-T surge protection let-
through <5%
(As a percentage of an applied ±6kV 1.2/50µs, 500A 8/20µs test)
Telephone line surge protection
let-through 1%
(As a percentage of an applied ±6kV 1.2/50µs, 500A 8/20µs test)
Operating temperature 0 to +40 degrees C (+32 to 104 degrees F)
Storage temperature -15 to +45 degrees C (+5 to +113 degrees F)
Operating and storage relative
humidity 0 to 95% non-condensing
Operating elevation 0 to +3000 m (0 to +10,000 ft)
Electromagnetic immunity IEC 801-2 level IV, 801-4 level IV, 801-5 level III
Audible noise in dbA at 1 meter < 45
Audible alarm On Overload, Low battery warning, On battery
Communications port DB-9 Minuteman standard, optional SNMP
Size (H x W x D) 8.9 X 48.3 X 45.3 cm
(3.5 X 19.0 X 17.8 in) 13.2 X 48.3 X 50.4 cm (5.2 X 19.0 X 19.8 in)
Weight net (shipping) 19.8 (22.1) Kg
43.6 (48.6) Lb 26.6 (28.9) Kg 58.6 (63.6) Lb 29.7 (32.0) Kg 65.4 (70.4) Lb 46.4 (49.1) Kg 102 (108) Lb
Battery pack Available on the 2200 only (Pro BP1)
Battery pack size (HxWxD) and
weight 8.9 X 48.3 X 45.3 cm (32.1 Kg) 3.5 X 19.0 X 17.8 in (70.7 Lb)
Conformance UL 1778, CSA C22.2,
FCC Class A, TUV/GS, CE,
EN50091-1, EN50091-2, EN60950,
EN50082-1, EN55022, EN61000-3-2 & EN61000-3-3
*Note: The input voltage range is adjustable via software. For input voltages less than 8% or more than
12% of nominal, the voltage regulator will boost or reduce the input voltage by 15%.

15
NOTE: These items require optional software or hardware.
Function Factory Default User Choices Description
UPS ID Model number Up to 64 characters to
define the UPS Use this function to uniquely identify the UPS
in your network
configuration
Battery install date Date of manufacture Date of battery
replacement -
day/month/year
XX/XX/XXXX
Enter the current date
when replacing batteries
Battery life in days 1826 Up to 5 characters At first battery
replacement, reset to
reflect actual number of
days experience in your
environment or leave
factory default.
Enable/Disable auto
restart Enabled Enable or disable When enabled, the UPS
will automatically restart
from a low battery
shutdown when normal
A/C returns
Set audible alarm state Enabled Enabled, at low battery,
disabled, Mute Enabled - the UPS will
emit a short beep when in
the battery mode. At Low
Battery the UPS will emit
a steady tone only at low
battery warning through
shutdown.
Disabled - Use only when
software is controlling the
UPS or to silence the
alarm Mute - Attenuates
the alarm by 50%
Shutdown Type UPS output UPS output or UPS UPS Output - When the
UPS is told to shut down,
it turns off the UPS output
only. UPS - Turns off the
UPS which requires the
UPS to be turned on
manually
Set low voltage Xfer point 92 VAC
(176 for 230VAC models) 92 or 88 VAC (176 or 166 for 230VAC
models)
Changes the voltage
point at which the UPS
switches to battery power
Set high voltage Xfer
point 150 VAC (282 for 230VAC models) 150 or 145 VAC (282 or 272 for 230VAC
models)
Changes the voltage
point at which the UPS
switches to battery power
Set nominal input voltage 115 VAC
(230 for 230VAC models) 110,115,120 VAC (220, 230, 240 for
230VAC models)
Changes the output
voltage
Baud Rate 9600 1200, 2400, 4800, 9600 Sets the communication
baud rate

16
LIMITED PRODUCT WARRANTY
Para Systems Inc. (Para Systems) warrants this equipment, when properly applied
and operated within specified conditions, against faulty materials or workmanship for a
period of three years from the date of original purchase by the end user. For equipment
sites within the United States and Canada, this warranty covers repair or replacement of
defective equipment at the discretion of Para Systems. Repair will be from the nearest
authorized service center. Replacement parts and warranty labor will be borne by Para
Systems. For equipment located outside of the United States and Canada, Para Systems
only covers faulty parts. Para Systems products repaired or replaced pursuant to this
warranty shall be warranted for the unexpired portion of the warranty applying to the
original product. This warranty applies only to the original purchaser who must have
properly registered the product within 10 days of purchase.
The warranty shall be void if (a) the equipment is damaged by the customer, is
improperly used, is subjected to an adverse operating environment, or is operated outside
the limits of its electrical specifications; (b) the equipment is repaired or modified by anyone
other than Para Systems or Para Systems-approved personnel; or (c) has been used in a
manner contrary to the product’s operating manual or other written instructions.
Any technical advice furnished before or after delivery in regard to use or application
of Para Systems’ equipment is furnished without charge and on the basis that it represents
Para Systems’ best judgment under the circumstances, but it is used at the recipient’s sole
risk.
EXCEPT AS PROVIDED HEREIN, PARA SYSTEMS MAKES NOWARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation of implied
warranties; therefore, the aforesaid limitation(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL PARA SYSTEMS BE
LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE. Specifically, Para Systems is not liable for any
costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of
software, loss of data, cost of substitutes, claims by third parties, or otherwise. The sole
and exclusive remedy for breach of any warranty, expressed or implied, concerning Para
Systems’ products and the only obligation of Para Systems hereunder, shall be the repair
or replacement of defective equipment, components, or parts; or, at Para Systems’ option,
refund of the purchase price or substitution with an equivalent replacement product. This
warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
Longer term and F.O.B. job site warranties are available at extra cost. Contact Para
Systems (1-972-446-7363) for details.
LIMITED PRODUCT WARRANTY
10

17
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC, 73/23/EEC
Standard(s) to which Conformity is Declared: EN50091-1, EN50091-2
EN50082-1, EN55022, EN60950, EN61000-3-2, EN61000-3-3
Manufacturer’s Name: Para Systems, Inc. (Minuteman Power Supplies)
Manufacturer’s Address: 1455 LeMay Drive
Carrollton, Texas 75007 USA
Type of Equipment: Uninterruptible Power Supplies
Model No: Pro 700ri, Pro 1000ri, Pro 1400ri, Pro 2200ri
Year of Manufacture: 1998,
I, the undersigned, hereby declare that the equipment specified above
conforms to the above Directive(s).
Place: Carrollton, Tx USA

(Signature)
Date: November 1, 1998 Shawn Delavar
(Full Name)
Regulatory Compliance Engineer

Para Systems, Inc.
1455 LeMay Dr.
Carrollton, TX 75007
Phone: [phone]
Fax: [phone]
QuickFax Info System: 1-800-263-3933
Internet: www minuteman-ups.com
PN: 34000033
Rev. 1