miRider GB3 User manual
About us
Welcome to the fold
Thank you for choosing to join the growing MiRiDER
community. We’re sure riding your MiRiDER One GB3 will
create some amazing new experiences and memories to last
a lifetime.
Our detailed User Manual follows. Please take some
time to read the Manual, as it will ensure you enjoy
your brand new bike and its many features.
However, should you have any unanswered questions
or queries, please don’t hesitate to contact us by
phone, email, or via the website.
Your enquiry will be handled by the Lancashire based
team who have developed the MiRiDER One GB3
from day one.
We’re a passionate bunch for both cycling and
producing the very best products we can.
Constantly testing and developing new ideas for
the bike itself and riding accessories, we aim to
become the UK’s leading folding eBike brand.
Enjoy your MiRiDER One GB3.
www.mirider.co.uk
+44 (0)1257 228242
Disklok House
Preston Road
Chorley
Lancashire
PR7 5HH
UKCA DECLARATION OF CONFORMITY
MiRiDER LIMITED
Disklok House,
Preston Rd,
Charnock Richard,
Chorley PR7 5HH
Declares under our sole responsibility that the product:
Mirider GB3
Foldable E-Bike
Conforms with the provisions of the following directives:
EMC Directive 2014/30/EU
Machinery 2006/42/EC
The following Harmonized standard were applied:
Cycles - Electrically power assisted cycles - EPAC Bicycles
EN15194:2017
This product carries the UKCA mark, which was first affixed in 2022.
Signed:
Date: 01/01/2019
Position: Sales Director
MiRiDER LTD.
Disklok House, Preston Rd
Chorley, Lancashire, PR7 5HH
Company Reg No.
11983977
VAT Reg No.
336 9565 62
Phone
+44 (0)1257 228242
Email
hello@mirider.co.uk
Website
www.mirider.co.uk
Bike structure and functions
Packing list
Instructions for use
LCD display instructions
Maintenance and storage
Safety advice
Warnings and precautions
Troubleshooting
Please read this manual carefully before using the MiRiDER One GB3 eBike.
This manual will help you understand the bike’s:
1. Basic operational process
2. Safety principles
3. Product structure, its care & use
Contents
Page 6
Page 7
Page 8 - 11
Page 12 - 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22 - 23
Page 24 - 25
Page 26
Warranty Page 27
Carrying & manoeuvring
Servicing
Charging the battery & changing gears
Battery charging precautions
Bike structure and functions
7
Items included:
1. 1 x MiRiDER one eBike
2. 1 x Seat saddle
3. Before you start
4. 1 x Charger
5. 1 x Battery
6. 2 x Mudguards
7. 1 x Bell
Before use
We recommend that you always wear a helmet and highly visible, protective clothing when
riding the MiRiDER One GB3.
Packing list
Folding the eBike frame To secure the eBike frame
Open the clamp to raise and lower the
handlebar height. Make sure the clamp is
closed fully before riding. Do not extend
higher than the grooved lines
4. Adjusting handlebar height
8
Instructions for use
1. 2.
On the lever opposite the folding hinge,
press down the red lever then pull the main
black handle outwards to release the frame
locking mechanism.
Connect the 2 halves of the frame together
and secure by pushing the black locking
sfir
click into its locked position.
Open the seat clamp, as shown in the
image above.
5. How to insert the seat
Securing the stem
Secure the hinge by pressing the black
snap shut.
9
Lift the handlebar stem upwards until
position.
sfir
3.
Adjust the seat post height by lifting the
lever on the post and adjusting the height
to the required level. Then close the lever
securing the seat post at this height.
6. Adjust saddle height
Push the seat into the frame to the
minimum insertion mark on the seat post
then secure the seat post by closing the
seat post clamp.
10
7. Folding the pedals
Press & hold the power button, on the LCD
screen for 3 seconds to turn the power on.
Connect the charger into the port if the
LCD screen does not activate.
8. Power On
To unfold, simply lift the pedal until it clicks
into position
To fold, pull the inner chrome latch
outwards to release the pedal
11
LCD display instructions
12
13
14
Push and hold the power ON/OFF button to activate
the display. The same button is to be pushed and
sss
Use the up and down arrows in the display to
increase or decrease the power assist level.
When pushing the bike, if you push and hold the
down arrow button on the display, walk assist
mode will be engaged providing 6km/h (4mph)
power assist to aid pushing the bike. As soon as you
release the down arrow this assistance will stop.
rssrsrs
ssssrrs
ON/OFF
Assistance Level
15
Holding the up arrow on the display turns on
the display bikes headlight. Push and hold the
sss
rssrsrs
a walk assist or start assist without pedalling to
a legal maximum of 4mph (this will reduce
depending on rider weight and incline). Secondly,
it will provide a full power boost (equivalent to
level 5) when the rider is pedalling - ideal for a
ssssrrs
Headlight
Thumb Throttle Assist
16
Fold the eBike frame and unlock the
battery lock using the battery locking key.
Pull out the battery from inside the frame,
using the handle, as shown in the image
above.
To re-insert the battery, push the battery
into position and lock it in place using the
locking key. Make sure the handle is folded
down again before closing.
Removing/Installing the battery
17
Option 1: Open the rubber charging port
grommet and insert the charging cable.
Then plug the charger into the mains and
switch on.
1) To increase gear - turn the twist grip away
from you
2) To reduce gear - turn the twist grip towards you
(note, you need to stop pedalling or reduce pressure
on the pedals to allow the gear to engage)
Tip - you do not need to be riding or moving to
change gear
Option 2: Fold the bike, remove the battery
and plug the charger into the port. Then plug
the charger into the mains and switch on.
Charging the battery
Changing gear
Your MiRiDER One GB3 should be serviced regularly, using an authorised
MiRiDER dealer is preferred as they are familiar with the bike. We recommend
rfirfirss
or 6 weeks (which ever comes sooner) as some items, such as brakes, take time
to bed in and may need adjusting to keep optimised performance.
Your MiRiDER One GB3’s gearbox needs to have a regular service as it is made
up of multiple moving parts which require adequate lubrication. Due to the
specialist oil and nature of the part, this task should only be performed by an
authorised MiRiDER dealer (check out our online locator map here for your nearest
centre (https://mirider.co.uk/try-a-mirider/). The service interval is once every
500 miles and is also an optimal time to check up or service the rest of the bike.
rrrfir
Servicing
Gearbox service
18
rfirfirss
Ensure the battery is charged between temperatures of 10-45°C
Always store the battery in a safe and dry place
rrrfir
Do not modify, damage or try to disassemble the battery
Always charge the battery with the supplied charger
Please read the ‘charging the battery’ section before charging the battery
Unplug the charger from the battery once the light shows green
If the charger indicator light stops working, or the charger overheats then
unplug the charger immediately and do not use
Ensure the charger does not come into contact with water
Ensure the charger is stored in a safe and dry place
Do not allow battery level to be completely exhausted
Do not attempt to disassemble or replace any parts of the charger
Do not put the battery or charger in places where it may fall to the ground.
This may cause damage
If the battery or charger become damaged please stop using immediately
Only dispose of batteries according to the local laws and regulations of
your region
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
19
How to carry and manoeuvre
the bike
Maintenance and storage
1. Ensure the bike is stored in a secure, cool and dry place when not in use.
2. Do not use any chemical solvents to clean the bike, as this may corrode the surface.
3. rsrrfir
bike retailer and the below checks are followed.
20
Suggested regular maintenance checks:
Parts Maintenance checks
Brakes srrrsrsffi
stopping power before use.
Tyres Ensure the tyres have no damage, enough tread
rssrssffisr
rrssrsssr
Shock absorber Check the shock absorber is free moving with no
knocking noise.
Throttle Check the throttle deactivates when released and
moves freely.
Screws/bolts Check for any loose fastenings and tighten as required.
Wheels Check for signs of damage, wear and tear, and ensure
all nuts, bolts and spokes are tight.
Battery Ensure after a full charge the LCD screen shows the
battery indicator being full.
Charger Check that the red light appears when charging and
turns to green once fully charged.
Chain and
Sprocket
Clean regularly and apply bike chain lubricant.
Check chain isn’t too slack.
eBike cleaning Regularly clean the eBike with a clean, damp cloth.
Wires/cables Ensure there is no visible damage.
Table of contents
Other miRider Bicycle manuals
