miseno Wallace MH-6WAL-ORB User manual

TOOLS REQUIRED
AA Deadbolt Screws
BB Mounting screws
CC Latch/Strike Screws
DD Handleset Screw
EE Reinforcement Screws
2
2
8
1
1
1
Part Description Quantity
OR 20
FF Allen wrench
GG Set screw
OptionalOptional
USE AND CARE GUIDE
FOR
WARNING
If the door needs to be drilled, be familiar with how to use your drill safely, and understand all the
door preparation steps before proceeding.
NOTE
T
door. Periodically clean the locks with mild soap and a soft cloth. Do not use abrasives or harsh
chemicals, and avoid sharp or scratching objects.
Read the precautions and instructions in this manual before installing and using this lock.
Save this manual for future reference.
1
2
Safety Information
CAUTION
Before beginning the installation, please read and understand the entire manual.
Part Description Quantity
Thumbturn
Deadbolt Latch
Outside Cylinder
Inside Cylinder
1
1
1
1
1
1
A
B
C
E
D
F
Handleset
1G
Latch
1H
Interior rose plate
Inside Knob/Lever
Interior rose
1
1
1
1
1
I
J
K
M
1
N
1
O
L
Pre-Installation —Tools Required/Hardware Included
Optional Optional
1’’ (25 mm)
1/2’’ (13 mm)
3
Using the template, mark the door and drill the holes, and chisel out a mortise.
NOTE: Drill from both sides to avoid wood splitting.
Pre-Installation (continued) — Door Preparation
NOTE: If your door already has holes, skip to Installation.
NOTE: To assure proper lockset function, the holes in the door jamb must be drilled 1/2’’ (13 mm)
and 1’’ (25 mm) deep.
Prepare the door jamb – using the strike plate as a pattern, drill the latch and screw holes, and
FKLVHORXWDPRUWLVHXQWLOWKHVWULNHSODWHğWVĠXVK
OR
OR
NOTE: Ensure the lip faces
away from the door.
2
8
3
2
4
3
B. Set the latch backset
C. Install the latch
NOTE: The bevel should face the door jamb.
CAUTION: Be sure the latch cam is upright before making any backset adjustment.
.
OR
Inside square plate
2-3/8” (60 mm)
2-3/4” (70 mm)
Right
Wrong
2-3/8” (60mm)
2-3/4” (70mm)
OR
2
8
3
2
8
3
2
8
3
2
-
3
/
8
”
(6
0mm)
180º
2
8
3
24
3
2
-3
/
4
”
(
7
0
m
m
)
2
8
3
2
4
3
EE DD
CC
BB
AA
A
E
F
G
H
I
J
K
L
N
M
O
M
B
C
D
Washer
Latch Strike
Reinforcement Plate
Screw Cover (Optional)
Deadbolt Strike
4
Installing the latch
Installation
A. Attach the correct faceplate
OR OR
OR OR OR
OR
Note: Not to scale.
DDCCAA BB EE
FF GG

TEMPLATE MARK HEIGHT 36’’ (914 mm) FROM FLOOR TO CENTER
ø 3/8’’ (10 mm)
NOTE: Double check your product for the correct
hole sizes.
Install Handleset Installing the deadbolt trim
ø 2-1/8’’ (54 mm) ø 2-1/8’’ (54 mm)
S00-HP00R14P-XP
Rev. 17/04-02
Install Handleset Screw
OR
Fold here. Place on the door edge.
Drill a 1” (25 mm) diameter hole at the center of the door edge.
Drill a 1” (25 mm) diameter hole at the center of the door
1-3/4”
(45 mm)
1-3/8”
(35 mm)
1-9/16”
(40 mm)
1-3/4”
(45 mm)
1-3/8”
(35 mm)
1-9/16”
(40 mm)
CENTER TO CENTER 8-5/8” (219 mm)
CENTER TO CENTER
2-3/4” (70 mm)
Backset
2-3/8” (60 mm)
5-1/2” (140 mm)
Exterior
IF
IF
ExteriorInterior
Interior
ExteriorInterior
Exterior
Interior
Single cylinder deadbolt Double cylinder deadbolt
OR
OR
OR
OR
OR
OR
Install Inside Knob/Lever
Center-to-center distance
A : 8-7/16” (214mm)
B : 8-5/8” (219mm)
C : 8-31/32” (228mm)
A
B
C
Center-to-center
distance
Adjust center-to-center distance Some handleset applicable
HC,HP,HY7
edge.
Backset