miseno MM2028LEDR User manual

Model: MM2028LEDR, MM2432LEDR, MM3232LEDR, MM5636LEDR,
MM6028LEDR
LED LIGHTED MIRROR
USER GUIDE

IMPORTANT SAFETY INFORMATION
WARNING
This product must be installed in accordance with the installaon instrucon by
qualified technician. Failure to follow instrucon could result in death or serious
bodily injury.
Please read through this installaon instrucon so you will know how to install
and operate your model properly. Keep this document in a safe place for future
reference aer use.
CAUTION
This product must be serviced by qualified personnel. ALWAYS unplug the power
cord or turn off the circuit breaker before service.
PACKAGE CONTENTS
2
(x1)
Mirror
Mounng Bracket Screw Drywall Anchor
(Model MM2028LEDR x1)
(Model MM2432LEDR x1)
(Model MM3232LEDR x1)
(Model MM5636LEDR x1)
(Model MM6028LEDR x1)
(Model MM2028LEDR x4)
(Model MM2432LEDR x4)
(Model MM3232LEDR x4)
(Model MM5636LEDR x8)
(Model MM6028LEDR x8)
(Model MM2028LEDR x4)
(Model MM2432LEDR x4)
(Model MM3232LEDR x4)
(Model MM5636LEDR x8)
(Model MM6028LEDR x8)
Customer Service: [phone] or [email protected]

INSTALLATION
For drywall installaon,
mark the hole locaons and
drill Φ6mm holes for the
drywall anchors.
Insert provided drywall
anchors.
Install the mounng bracket.
Connect to 110V power
supply.
Hang the mirror to the wall and
make sure the bracket in the
back of the mirror lineup with
the mounng bracket properly.
Press the mirror down
slightly and make sure the
brackets fit properly.
3
•Using the wall studs to hang the mirror is highlyrecommended.
•This mirror is NOT designed to work with dimmable wall switch.
•IR sensor requires a minimum clearance of 5 1/4”.
Customer Service: [phone] or [email protected]

INSTALLATION DIMENSIONS
Model # A B C
20 28 1 5/8
24 32 1 5/8
32 32 1 5/8
56 36 1 5/8
60 28 1 5/8
A
B
C
4Customer Service: [phone] or [email protected]
MM2028LEDR
MM2432LEDR
MM3232LEDR
MM5636LEDR
MM6028LEDR

BASIC OPERATION
1. Rocker switch
a. Turn switch to <–> posion; lights can be controlled by the IR sensor.
b. Turn switch to <o> posion to turn offthe lights.
c. Turn switch to <=> posion to turn on the lights.
2. Dimmable IR sensor
a. Turn the Rocker switch to <–> posion to acvate the IR sensor.
b. Move your hand across the IR sensor to turn the lights on or off.
c. The distance between your hand and the sensor should be approx. 1”.
d. To adjust the brightness of the lights, keep your hand in front of the
sensor unl the desirable brightness has reached and move your hand
away from the sensor.
e. If the lights flicker, the level of brightness might be too low; try to
adjust the brightness to a higher level.
5
Customer Service: [phone] or [email protected]

CARE AND MAINTENANCE
Clean the mirror with a so, damp cloth and dry thoroughly with a sotowel. Do NOT allow
the edges of the mirror to get or remain wet over a period of me. Please do NOT use glass
cleaner that contains ammonia or vinegar. Never spray any cleaner directly onto a mirror.
Instead apply the cleaner to a socloth and then wipe the mirror. Make sure no
commercial cleaner comes in contact with the edge or backing.
6
WARRANTY
DEFECTIVE GOODS CONSUMER WARRANTY
MISENO inspects all of its products prior to shipment. We offer a 5-year Limited warranty
on our electric mirror products. Defecve products should be returned to place of purchase
for replacement. However, if this is not possible, we accept returns on defecve product
with our wrien authorizaon. Returns will be handled by product replacement. Defects
or damage caused to product by the consumer are not accepted.
SHORTAGE OR DAMAGED PRODUCTS
All shipments are carefully inspected and counted before leaving our distribuon centers.
Please inspect carefully on receipt of merchandise, nong any discrepancy or damage on
the carrier’s freight bill at that me, and file a claim with the carrier within 10 days from
receipt of order. Then contact our office. Deducons from invoices for shortages or
damage claims will not be allowed.
RETURN NEW GOODS
All claims for returns or adjustments must have prior approval
and return authorizaon (RGA) number. Only original, sealed
product in salable condion are eligible for return. Credit for authorized returns will be
issued at the net price paid for the product and subject to a 15% restocking/handling fee.
Merchandise is to be returned via prepaid freight. All unauthorized returns will be refused
or subject to a 25% restocking/handling fee.
Customer Service: [phone] or [email protected]

REPLACEMENT PARTS
Part Descripon
1 Mirror
2 Rocker Switch
3Dimmable IR
Sensor
4Aluminum
Frame
5Connecon
Box
6 LED Driver
7IR Sensor
Driver
8LED Strip
Support
9 LED Strip
10 Galvanized
Plate
11 Cable Gland
12 Mounng
Bracket
7
Customer Service: [phone] or [email protected]

© MISENO All rights reserved.
401 Oerson Drive
Chico, CA 95928
www.miseno.com
V6.1