Mitsubishi Electric CITY MULTI PLFY-EP NEMU-E1 Series User manual

Air-Conditioners For Building Application
INDOOR UNIT
PLFY-EP·NEMU-E
PLFY-EP·NEMU-E1
MANUEL D’UTILISATION
Pour une utilisation correcte sans risques, veuillez lire le manuel d’utilisation en entier avant de vous servir du
climatiseur.
OPERATION MANUAL
For safe and correct use, please read this operation manual thoroughly before operating the air-conditioner unit.
MANUAL DE INSTRUCCIONES
Lea este manual de instrucciones hasta el nal antes de poner en marcha la unidad de aire acondicionado para
garantizar un uso seguro y correcto.
POUR L’UTILISATEUR
FOR USER
PARA EL USUARIO
English
Español
Français
RH79A057H01_01en.indd 1 2020/03/17 18:52:51
001

1
Contents
1. Safety Precautions
Before installing the unit, make sure you read all the “Safety
Precautions”.
The “Safety Precautions” provide very important points regard-
ing safety. Make sure you follow them.
Please report to or take consent by the supply authority before
connection to the system.
Symbols used in the text
Warning:
Describes precautions that should be observed to prevent danger of
injury or death to the user.
Caution:
Describes precautions that should be observed to prevent damage to the
unit.
Symbols used in the illustrations
: Indicates a part which must be grounded.
Warning:
• For appliances not accessible to the general public.
• The unit must not be installed by the user. Ask the dealer or an
authorized company to install the unit. If the unit is installed im-
properly, water leakage, electric shock or re may result.
• Do not stand on, or place any items on the unit.
• Do not splash water over the unit and do not touch the unit with
wet hands. An electric shock may result.
• Do not spray combustible gas close to the unit. Fire may result.
• Do not place a gas heater or any other open-ame appliance where
it will be exposed to the air discharged from the unit. Incomplete
combustion may result.
• Do not remove the front panel or the fan guard from the outdoor
unit when it is running.
• Never repair the unit or transfer it to another site by yourself.
• When you notice exceptionally abnormal noise or vibration, stop
operation, turn off the power switch, and contact your dealer.
• Never insert ngers, sticks etc. into the intakes or outlets.
• If you detect odd smells, stop using the unit, turn off the power
switch and consult your dealer. Otherwise, a breakdown, electric
shock or re may result.
• This air conditioner is NOT intended for use by children or inrm
persons without supervision.
• Young children must be supervised to ensure that they do not play
with the air conditioner.
• If the refrigeration gas blows out or leaks, stop the operation of the
air conditioner, thoroughly ventilate the room, and contact your
dealer.
• When installing or relocating, or servicing the air conditioner, use
only the specied refrigerant (R410A) to charge the refrigerant
lines. Do not mix it with any other refrigerant and do not allow air
to remain in the lines.
If air is mixed with the refrigerant, then it can be the cause of ab-
normal high pressure in the refrigerant line, and may result in an
explosion and other hazards.
The use of any refrigerant other than that specied for the system
will cause mechanical failure or system malfunction or unit break-
down. In the worst case, this could lead to a serious impediment
to securing product safety.
Caution:
• Do not use any sharp object to push the buttons, as this may dam-
age the remote controller.
• Never block or cover the indoor or outdoor unit’s intakes or outlets.
• Never wipe the remote controller with benzene, thinner chemical
rags, etc.
• Do not operate the unit for a long time in high humidity, e.g. leaving
a door or window open. In the cooling mode, if the unit is operated
in a room with high humidity (80% RH or more) for a long time, wa-
ter condensed in the air conditioner may drop and wet or damage
furniture, etc.
• Do not touch the upper air outlet vane or the lower air outlet damper
during operation. Otherwise, condensation may form and the unit
may stop operating.
Disposing of the unit
When you need to dispose of the unit, consult your dealer.
Notes:
The phrase “Wired remote controller” in this operation manual refers only to the PAR-40MAA.
The phrase “Simple MA Remote Controller” in this operation manual refers to the PAC-YT53CRAU.
If you need any information for the other remote controller, please refer to the instruction book included in these box.
1. Safety Precautions ............................................................................ 1
2. Parts Names...................................................................................... 2
3. Operation (For Wired Remote controller) .......................................... 5
4. Operation (For Simple MA remote controller).................................. 12
5. Timer................................................................................................ 15
6. Care and Cleaning........................................................................... 16
7. Trouble Shooting ............................................................................. 17
8. Specications .................................................................................. 19
en
RH79A057H01_01en.indd 1 2020/03/17 18:52:51
002

MENU ON
OFF
RETURN SELECT
HOLD
2
2. Parts Names
■Indoor Unit
PLFY-EP·NEMU-E
PLFY-EP·NEMU-E1
Fan steps 4 steps
Vane Auto with swing
Louver –
Filter Long-life
Filter cleaning indication 2,500 hr
Enter the model setting number for
the indoor unit you want to operate. 225 (001)
Air outlet Filter
Air intake
Vane
■Wired Remote Controller
The functions of the function buttons change depending on the
screen.
Refer to the button function guide that appears at the bottom of the
LCD for the functions they serve on a given screen.
When the system is centrally controlled, the button function guide
that corresponds to the locked button will not appear.
▌1[ON/OFF] button
Press to turn ON/OFF the indoor unit.
▌2 [SELECT/HOLD] button
Press to save the setting.
When the Main menu is displayed, pressing this button will enable/dis-
able the HOLD function.
▌3[RETURN] button
Press to return to the previous screen.
▌4[MENU] button
Press to bring up the Main menu.
▌5Backlit LCD
Operation settings will appear.
When the backlight is off, pressing any button turns the backlight on
and it will stay lit for a certain period of time depending on the screen.
When the backlight is off, pressing any button turns the backlight on
and does not perform its function. (except for the [ON/OFF] button)
▌6ON/OFF lamp
This lamp lights up in green while the unit is in operation. It blinks while
the remote controller is starting up or when there is an error.
▌7Function button [F1]
Main display: Press to change the operation mode.
Menu screen: The button function varies with the screen.
▌8Function button [F2]
Main display: Press to decrease temperature.
Main menu: Press to move the cursor left.
Menu screen: The button function varies with the screen.
▌9Function button [F3]
Main display: Press to increase temperature.
Main menu: Press to move the cursor right.
Menu screen: The button function varies with the screen.
▌0 Function button [F4]
Main display: Press to change the fan speed.
Menu screen: The button function varies with the screen.
Controller interface
Main display
Menu screen
Function guide
Main menu
83
83
Fri
Room
Set temp.
Mode Temp. Fan
Cool Auto
Main Main menu
Energy saving
Main display:
Cursor
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
RETURN
7890
7890
7890
4 32 1
5
6
7890
Function buttons
* When using a wireless remote controller, input the “model setting number” (refer to the table above) on the wireless remote controller.
• If the outdoor unit is “Simultaneous Cooling and Heating type (Operation mode: Auto is selectable)”, input the model setting number in ( ).
• Refer to the installation manual of wireless remote controller for the procedure to set the model of wireless remote controller.
en
RH79A057H01_01en.indd 2 2020/03/17 18:52:52
003

3
Fri
Cool
Mode Temp. Fan
Set temp. Auto
83
Fri
Mode Temp. Fan
Room
Cool Set temp. Auto
83
83
2. Parts Names
The main display can be displayed in two different modes: “Full” and “Basic”. The factory setting is “Full”. To switch to the “Basic” mode, change the
setting on the Main display setting. (Refer to operation manual included with remote controller.)
▌1Operation mode
▌2Preset temperature
▌3Clock
▌4Fan speed
▌5Button function guide
Functions of the corresponding buttons appear here.
▌6
Appears when the ON/OFF operation is centrally controlled.
▌7
Appears when the operation mode is centrally controlled.
▌8
Appears when the preset temperature is centrally controlled.
▌9
Appears when the lter reset function is centrally controlled.
▌0
Indicates when lter needs maintenance.
▌1Room temperature
▌2
Appears when the buttons are locked.
▌3
Appears when the On/Off timer or Auto-off timer function is enabled.
appears when the timer is disabled by the centralized control
system.
appears when the HOLD function is enabled.
<Full mode>
* All icons are displayed for explanation.
<Basic mode>
4
3
2!
1
5
6
#
7
8
90
1
3
9
4
)
@
$2
1
#
5
▌4
Appears when the Weekly timer is enabled.
▌5
Appears while the units are operated in the energy-save mode. (Will
not appear on some models of indoor units)
▌6
Appears while the outdoor units are operated in the silent mode.
▌7
Appears when the built-in thermistor on the remote controller is acti-
vated to monitor the room temperature (1).
appears when the thermistor on the indoor unit is activated to
monitor the room temperature.
▌8
Indicates the vane setting.
▌9
Indicates the louver setting.
▌)
Indicates the ventilation setting.
▌!
Appears when the preset temperature range is restricted.
▌@
Appears when an energy-saving operation is performed using a “3D i-
See sensor” function.
▌#Centrally controlled
Appears for a certain period of time when a centrally-controlled item is
operated.
▌$Preliminary error display
An error code appears during the preliminary error.
Display
Most settings (except ON/OFF, mode, fan speed, temperature)
can be made from the Main menu. (Refer to Page 7.)
32$45 6 7 8
en
RH79A057H01_01en.indd 3 2020/03/17 18:52:53
004

4
2. Parts Names
Simple MA Remote Controller
.
ON/OFF lamp
The lamp will light up in green when turned on, and blink during startup and when an error occurs.
Backlit LCD
button
buttonTEMP.
MODE
buttonON/OFF
Pressing this button starts and stops the operation.
buttonFAN
buttonVANE
* To set the functions that are not available on this controller (PAC-YT53CRAU) such as Louver, use MA remote controller or the centralized controller.
* All icons are displayed for explanation.
CENTRAL icon *1
CHECK icon *2
Preset temperature *3 icon appears while the unit is operated in the energy-save mode
icon appears when Operation lock setting is effective.
icon appears when indoor unit functions are set up. (Refer to the Installation Manual.)
Fan speed icon
Vane icon
icon appears when the power is on.
Operation modes
Indoor temperature
*1
CENTRAL
icon
Appears when one of the following local operations is prohibited: ON/OFF; operation mode; preset temperature; fan speed; vane.
*2 icon
When an error occurs, power indicator will blink, and unit address (three digits) and error code (four digits) will blink.
Check the error status, stop the operation, and consult your dealer.
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
Unit address
blinks.
Error code blinks.
When only error code blinks, air conditioning units stay in operation, but an error may have occurred.
Check the error code, and consult your dealer.
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
Error code blinks.
*3 Preset temperature
* Centigrade or Fahrenheit is selectable. Refer to the Installation Manual for details.
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
Preset temperature
In COOL, DRYING, HEAT, or
AUTO (single set point) modes
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
Heating preset temperature
In AUTO (dual set point) or
SETBACK modes
Cooling preset temperature
Controller interface
Display
en
RH79A057H01_01en.indd 4 2020/03/17 18:52:54
005

5
3. Operation (For Wired Remote controller)
■About the operation method, refer to the operation manual that comes with each remote controller.
3.1. Turning ON/OFF
[ON] [OFF]
Press the [ON/OFF] button.
The ON/OFF lamp will light up in green,
and the operation will start.
When “LED lighting” is set to “No”, the
ON/OFF lamp will not light up.
Press the [ON/OFF] button again.
The ON/OFF lamp will come off, and
the operation will stop.
■Operation status memory
Remote controller setting
Operation mode Operation mode before the power was turned off
Preset temperature Preset temperature before the power was turned off
Fan speed Fan speed before the power was turned off
■Settable preset temperature range
Operation mode Preset temperature range
COOL/DRYING 67 - 87 (95) °F/19 - 30 (35) °C
HEAT 63 (40) - 83 °F/17 (4.5) - 28 °C
AUTO (single set point) 67 - 83 °F/19 - 28 °C
AUTO (dual set point) [COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *1, *2
SETBACK [COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *2
FAN, VENTI. Unsettable
*1 The preset temperatures for cooling and heating for AUTO (dual set point) mode will be used for those for COOL/DRYING and HEAT mode.
*2 The preset temperatures for cooling and heating can be set under the following conditions.
• The cooling preset temperature is greater than the heating preset temperature.
• The difference between the cooling and heating preset temperatures is equal or greater than the minimum temperature difference that varies depending on the indoor
unit model to be connected.
The settable temperature range varies with the model of outdoor units and remote controller.
Note:
Even if you press the ON/OFF button immediately after shutting down the operation is progress, the air conditioner will not start for about 3 minutes.
This is to prevent the internal components from being damaged.
3.2. Operation mode
Each pressing of the [F1] button cycles
through the following operation modes.
Select the desired operation mode.
• Operation modes that are not available
to the connected outdoor unit models will
not appear on the display.
What the blinking mode icon means
The mode icon will blink when other indoor units in the same refrigerant
system (connected to the same outdoor unit) are already operated in a
different mode. In this case, the rest of the unit in the same group can
only be operated in the same mode.
3.3. Temperature setting
<Cool, Drying, Heat, and Auto (Single set point)>
Cool
Auto
Drying
Heat
Fan
Press the [F2] button to decrease the preset temperature, and press the
[F3] button to increase.
•Refer to the table on page 5 for the settable temperature range for dif-
ferent operation modes.
•Preset temperature range cannot be set for Fan/Ventilation operation.
• Preset temperature will be displayed either in Centigrade in 0.5- or
1-degree increments, or in Fahrenheit, depending on the indoor unit
model and the display mode setting on the remote controller.
Cool
Room
AutoSet temp.
Mode Temp. Fan
Fri
83
83
MENU
ON
OFF
RETURN SELECT
HOLD
Operation mode
Room temperature (Refer to the Installation Manual.)
Cool
Room
AutoSet temp.
Mode Temp. Fan
Fri
83
83
MENU
ON
OFF
RETURN SELECT
HOLD
ON
OFF
Setback
ON
OFF
en
RH79A057H01_01en.indd 5 2020/03/17 18:52:54
006

6
3. Operation (For Wired Remote controller)
Automatic operation (Dual set point)
When the operation mode is set to the “ Auto ” (dual set point) mode, two
preset temperatures (one each for cooling and heating) can be set. De-
pending on the room temperature, indoor unit will automatically operate
in either the “ Cool ” or “ Heat ” mode and keep the room temperature within
the preset range.
The graph below shows the operation pattern of indoor unit operated in
the
“ Auto ” (dual set point) mode.
Operation pattern during Auto (dual set point) mode
HEAT COOL HEAT COOL
Preset temp.
(COOL)
Preset temp.
(HEAT)
Room
temperature
The room temperature
changes corresponding
to the change in the
outside temperature.
Setback mode
Room temperature is controlled to stay within the set temperature range
that is speci ed for the Setback mode. By leaving suf cient temperature
differential between the set temperature for cooling (upper limit) and heating
(lower limit), it is possible to keep the room temperature within the speci ed
range without overworking the air conditioners.
This setting will be especially effective during periods of non-occupancy.
Operation pattern during Setback mode
HEAT COOL HEAT COOL
Set temp.
(
SETBACK_COOL )
Set temp.
(
SETBACK_HEAT )
Room
temperature
The room temperature
changes corresponding
to the change in the
outside temperature.
3.4. Fan speed setting
MENU
ON
OFF
RETURN SELECT
HOLD
83
83
Cool
Room
AutoSet temp.
Mode Temp. Fan
Fri
Each pressing of the [F4] button cycles through the following fan speeds.
Auto
• The available fan speeds depend on the models of connected indoor
units.
Notes:
● The number of available fan speeds depends on the type of unit
connected. Note also that some units do not provide an “Auto”
setting.
● In the following cases, the actual fan speed generated by the unit
will differ from the speed shown the remote controller display.
1. While the display is showing “STAND BY” or “DEFROST”.
2. When the temperature of the heat exchanger is low in the heat
mode. (e.g. immediately after heat operation starts)
3. In HEAT mode, when room temperature is higher than the
temperature setting.
4. When the unit is in Drying mode.
Automatic operation (Single set point)
According to a set temperature, cooling operation starts if the room tem-
perature is too hot and heating operation starts if the room temperature
is too cold.
During automatic operation, if the room temperature changes and
remains 1.5 °C, 4 °F or more above the set temperature for 3 minutes,
the air conditioner switches to cool mode. In the same way, if the room
temperature remains 1.5 °C, 4 °F or more below the set temperature for
3 minutes, the air conditioner switches to heat mode.
Cool mode 3 minutes (switches from
heating to cooling)
Set temperature +1.5 °C, +4 °F
Set temperature
Set temperature -1.5 °C, -4 °F
3 minutes (switches from
cooling to heating)
Because the room temperature is automatically adjusted in order to
maintain a  xed effective temperature, cooling operation is performed a
few degrees warmer and heating operation is performed a few degrees
cooler than the set room temperature once the temperature is reached
(automatic energy-saving operation).
<Auto (dual set point) mode>
68
83
79
MENU
ON
OFF
RETURN SELECT
HOLD
Preset temperature
for cooling
Preset temperature
for heating
1 The current preset temperatures will appear. Press the [F2] or [F3]
button to display the setting screen.
MENU
ON
OFF
RETURN SELECT
HOLD
68
83
RETURN
Preset temperature
for cooling
Preset temperature
for heating
83
68
2Press the [F1] or [F2] button to move the cursor to the desired
temperature setting (cooling or heating).
Press the [F3] button to decrease the selected temperature, and
press the [F4] button to increase.
• Refer to the table on page 5 for the settable temperature range for
different operation modes.
• The preset temperature settings for cooling and heating in the Auto
(dual set point) mode are also used by the Cool/Drying and Heat
modes.
• The preset temperatures for cooling and heating in the Auto (dual
set point) mode must meet the conditions below:
• Preset cooling temperature is higher than preset heating temperature.
• The minimum temperature difference requirement between cooling and
heating preset temperatures (varies with the models of indoor units
connected) is met.
* If preset temperatures are set in a way that does not meet the minimum
temperature difference requirement, both preset temperatures will
automatically be changed within the allowable setting ranges.
Navigating through the screens
• To return to the Main screen ...... [RETURN] button
en
RH79A057H01_01en.indd 6 2020/03/17 18:52:55
007

7
3.5. Air ow direction setting
3.5.1 Navigating through the Main menu
<Accessing the Main menu>
Main Main menu
Operation
MENU
ON
OFF
RETURN SELECT
HOLD
<Item selection>
MENU
ON
OFF
RETURN SELECT
HOLD
Main Main menu
Initial setting
3. Operation (For Wired Remote controller)
3.5.2 Vane·Vent. (Lossnay)
<Accessing the menu>
MENU
ON
OFF
RETURN SELECT
HOLD
Main Main menu
Operation
MENU
ON
OFF
RETURN SELECT
HOLD
Main menu: RETURN
Cursor
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
<Vane setting>
MENU
ON
OFF
RETURN SELECT
HOLD
Fri
Off
Vent.Vane Louver
Swing Off
(Sample screen on CITY MULTI)
Press the [MENU] button on the
Main display.
The Main menu will appear.
Press [F2] to move the cursor left.
Press [F3] to move the cursor right.
Cursor
Select “Operation” from the Main
menu (refer to page 7), and press
the [SELECT/HOLD] button.
Select “Vane·Louver·Vent. (Loss-
nay)” from the Operation menu, and
press the [SELECT/HOLD] button.
Press the [F1] or [F2] button to go
through the vane setting options:
“Auto”, “Step 1”, “Step 2”, “Step 3”,
“Step 4”, “Step 5” and “Swing”.
Select the desired setting.
Auto
Swing
Select “Swing” to move the vanes
up and down automatically.
When set to “Step 1” through “Step
5”, the vane will be  xed at the se-
lected angle.
• under the vane setting icon
This icon will appear when the vane
is set to “Step 5” and the fan oper-
ates at low speed during cooling or
drying operation (depends on the
model).
The icon will go off in an hour, and
the vane setting will automatically
change.
Auto
Step 3
Swing
Step 1
Step 4
Step 2
Step 5
<Exiting the Main menu screen>
MENU
ON
OFF
RETURN SELECT
HOLD
83
83
Cool
Room
AutoSet temp.
Mode Temp. Fan
Fri
<Display of unsupported functions>
Title
Not available
Unsupported function
Return: RETURN
MENU
ON
OFF
RETURN SELECT
HOLD
The message at left will appear if
the user selects a function not sup-
ported by the corresponding indoor
unit model.
If no buttons are touched for 10
minutes, the screen will automati-
cally return to the Main display. Any
settings that have not been saved
will be lost.
Press the [RETURN] button to exit
the Main menu and return to the
Main display.
83
83
Fri
Room
Set temp.
Mode Temp. Fan
Cool Auto
en
RH79A057H01_01en.indd 7 2020/03/17 18:52:55
008

8
3. Operation (For Wired Remote controller)
Note: “0” indicates all outlets.
Horizontal airow
Downward
Outlet No. 2 Outlet No. 3
Outlet No. 1 Outlet No. 4
MITSUBISHI
ELECTRIC
label
Remote controller setting
The airow direction of this outlet
is controlled by the airow direc-
tion setting of remote controller.
Fixed
The airow direction of this outlet is xed
in particular direction.
* When it is cold because of direct air-
ow, the airow direction can be xed
horizontally to avoid direct airow.
< How to set the xed up/down air direction (Only for
wired remote controller) >
Note:
● This function cannot be set depending on the outdoor unit to be
connected.
• For PLFY-NEMU series, only the particular outlet can be xed to
certain direction with the procedures below. Once xed, only the set
outlet is xed every time air conditioner is turned on. (Other outlets
follow UP/DOWN air direction setting of remote controller.)
■Explanation of word
• “Refrigerant address No.” and “Unit No.” are the numbers given to
each air conditioner.
• “Outlet No.” is the number given to each outlet of air conditioner.
(Refer to the illustration below.)
•“Up/Down air direction” is the direction (angle) to x.
12345
Reset
horizontal
Notes:
● During swing operation, the directional indication on the screen
does not change in sync with the directional vanes on the unit.
●Available directions depend on the type of unit connected.
●In the following cases, the actual air direction will differ from the
direction indicated on the remote controller display.
1. While the display is in “STAND BY” or “DEFROST” states.
2. Immediately after starting heat mode (while the system is wait-
ing for the mode change to take effect).
3. In heat mode, when room temperature is higher than the tem-
perature setting.
<Ventilation setting>
Fri
Low
Vent.
MENU
ON
OFF
RETURN SELECT
HOLD
<Returning to the Operation menu>
MENU
ON
OFF
RETURN SELECT
HOLD
Main menu: RETURN
Cursor
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Press the [F3] button to go through
the ventilation setting options in the
order of “Off”, “Low”, and “High”.
* Settable only when Lossnay unit is
connected.
Off Low High
Off Low High
• The fan on some models of indoor
units may be interlocked with certain
models of ventilation units.
Press the [RETURN] button to go
back to the Operation menu.
en
RH79A057H01_01en.indd 8 2020/03/17 18:52:55
009

9
3. Operation (For Wired Remote controller)
■Conrmation procedure
Manual vane angle
Input display: SELECT
Address Check
1
M-NET address
Identify unit Check button
Return: RETURN
with vane fully open.
Function setting for unit
Manual vane angle
M-NET address 1
Return: RETURN
Check Unit state.
No communication
Manual vane angle
1Select the “M-NET address” for
the units to whose vanes are to be
xed, with the [F2] or [F3] button.
Press the [F4] button to conrm the
unit.
2After pressing the [F4] button, wait
approximately 15 seconds, and
then check the current state of the
air conditioner.
→ The vane is pointing downward.
→ This air conditioner is displayed
on the remote controller.
→ All outlets are closed. → Press
the [RETURN] button and continue
the operation from the beginning.
→ The messages shown to the left
are displayed. → The target device
does not exist at this refrigerant
address.
• Press the [RETURN] button to
return to the initial screen.
3Change the “M-NET address” to
the next number.
• Refer to step 1to change the “M-
NET address” and continue with
the conrmation.
3Select the M-NET address for the
units to whose vanes are to be
xed, with the [F2] or [F3] button,
and press the [SELECT/HOLD]
button.
Press the [F4] button to conrm the
unit.
4The current vane setting will ap-
pear.
Select the desired outlets from “1”,
“2”, “3”, “4”, or “1, 2, 3, 4 (all out-
lets)” with the [F1] or [F2] button.
Press the [F3] or [F4] button to go
through the following options and
select the desired setting.
■Manual vane angle
Main menu: RETURN
Cursor
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
MENU
ON
OFF
RETURN SELECT
HOLD
Setting display: SELECT
Cursor
Comfort
Manual vane angle
3D i-See sensor
MENU
ON
OFF
RETURN SELECT
HOLD
1Select “Comfort” from the Op-
eration menu, and press the [SE-
LECT/HOLD] button.
2Select “Manual vane angle” with
the [F1] or [F2] button, and press
the [SELECT/HOLD] button.
No setting Step 1
Step 2 Step 3
Step 4 Step 5
Draft
reduction All outlets
Press the [SELECT/HOLD] button to save the settings.
A screen will appear that indicates the setting information is being trans-
mitted.
The setting changes will be made to the selected outlet.
The screen will automatically return to the previous screen when the
transmission is completed.
Make the settings for other outlets, following the same procedures.
If all outlets are selected, will be displayed the next time the
unit goes into operation.
Navigating through the screens
• To return to the previous screen ........... [RETURN] button
Manual vane angle
Input display: SELECT
Address Check
1
M-NET address
Identify unit Check button
MENU
ON
OFF
RETURN SELECT
HOLD
Select: SELECT
Manual vane angle
Outlet Angle
Setting
Manual vane angle
MENU
ON
OFF
RETURN SELECT
HOLD
en
RH79A057H01_01en.indd 9 2020/03/17 18:52:56
010

10
3. Operation (For Wired Remote controller)
3.6. 3D i-see Sensor setting
3.6.1 3D i-see Sensor setting
Main Main menu
Operation
MENU
ON
OFF
RETURN SELECT
HOLD
Main menu: RETURN
Cursor
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
MENU
ON
OFF
RETURN SELECT
HOLD
Setting display: SELECT
Cursor
Comfort
Manual vane angle
3D i-See sensor
MENU
ON
OFF
RETURN SELECT
HOLD
MENU
ON
OFF
RETURN SELECT
HOLD
Setting display: SELECT
Cursor
3D i-See sensor
Air distribution
Energy saving option
Seasonal airflow
2Select “Comfort” from the
Operation menu, and press the
[SELECT/HOLD] button.
3Select “3D i-See sensor” with the
[F1] or [F2] button, and press the
[SELECT/HOLD] button.
4Select the desired menu with the
[F1] or [F2] button, and press the
[SELECT/HOLD] button.
• Air distribution
Select the airow direction control
method when the airow direction
is set to “Auto”.
• Energy saving option
Operates the energy-save mode
according to whether persons are
detected in the room by the 3D
i-see Sensor.
• Seasonal airow
When the thermostat turns off, the
fan and the vanes operate accord-
ing to the control settings.
1Select the M-NET address for the
units to whose vanes are to be
xed, with the [F2] or [F3] button,
and press the [SELECT/HOLD]
button.
Press the [F4] button to conrm the
unit.
The vane of only the target indoor
unit is pointing downward.
2Select the menu with the [F4] but-
ton.
Default → Area → Direct/Indirect
→ Default…
Default: The vanes move the same
as during normal operation.
During cooling mode, all of the
vanes move to the horizontal air-
ow direction.
During heating mode, all of the
vanes move to the down airow
direction.
Area: The vanes move to the down
airow direction toward areas with
a high floor temperature during
cooling mode and toward areas
with a low oor temperature dur-
ing heating mode. Otherwise,
the vanes move to the horizontal
airow direction.
Direct/Indirect: The vanes auto-
matically move relative to the areas
where persons are detected.
The vanes operate as indicated in
the following table.
3When Direct/Indirect is selected,
set each air outlet.
Select the air outlet with the [F1] or
[F2] button, and change the setting
with the [F4] button.
After changing the settings for all of
the air outlets, press the [SELECT/
HOLD] button to save the settings.
* In order to enable this function,
the airow direction must be set
to “Auto”.
3.6.2 Air distribution
Air distribution
Input display: SELECT
Address Check
M-NET address
Identify unit Check button
MENU
ON
OFF
RETURN SELECT
HOLD
Air distribution
Select: SELECT
Cur.
M-NET address
Auto vane
Direct/Indirect setting
Direct/Indirect
MENU
ON
OFF
RETURN SELECT
HOLD
Vane setting
Direct Indirect
Cooling horizontal → swing keep horizontal
Heating keep downward downward → horizontal
MENU
ON
OFF
RETURN SELECT
HOLD
Direct/Indirect setting
: Direct
: Indirect
: Indirect
: Direct
Select: SELECT
Outlet Angle
1Select “Operation” from the Main
menu, and press the [SELECT/
HOLD] button.
en
RH79A057H01_01en.indd 10 2020/03/17 18:52:57
011

11
3. Operation (For Wired Remote controller)
3.6.3 Energy saving option
Energy saving option
Cursor
Setting display: SELECT
No occupancy energy save
Room occupancy energy save
No occupancy Auto-OFF
MENU
ON
OFF
RETURN SELECT
HOLD
Energy saving option
Select: SELECT
No occupancy energy save
Cooling/Heating
MENU
ON
OFF
RETURN SELECT
HOLD
Energy saving option
Select: SELECT
Room occupancy energy save
Cooling/Heating
MENU
ON
OFF
RETURN SELECT
HOLD
Energy saving option
Select: SELECT
Time
No occupancy Auto-OFF
120 min.
MENU
ON
OFF
RETURN SELECT
HOLD
MENU
ON
OFF
RETURN SELECT
HOLD
18:47 Thu
Shut down by
No Occupancy Auto-OFF
31/Dec 12:59
Notes:
Any person at the following places cannot be detected.
● Along the wall on which the air conditioner is installed
● Directly under the air conditioner
● Where any obstacle, such as furniture, is between the person and
the air conditioner
A person may not be detected in the following situations.
● Room temperature is high.
● A person wears heavy clothes and his/her skin is not exposed.
● A heating element of which temperature changes signicantly is
present.
● Some heat sources, such as a small child or pet, may not be sensed.
● A heat source does not move for a long time.
The 3D i-see Sensor operates once approximately every 3 minutes
to measure the floor temperature and detect persons in the room.
● The intermittent operating sound is a normal sound produced when
the 3D i-see Sensor is moving.
Notes:
● During swing operation, the directional indication on the screen
does not change in sync with the directional vanes on the unit.
●Available directions depend on the type of unit connected.
●In the following cases, the actual air direction will differ from the
direction indicated on the remote controller display.
1. While the display is in “STAND BY” or “DEFROST” states.
2. Immediately after starting heat mode (while the system is wait-
ing for the mode change to take effect).
3. In heat mode, when room temperature is higher than the tem-
perature setting.
3.7. Ventilation
For LOSSNAY combination
■The following 2 patterns of operation is available.
•Run the ventilator together with indoor unit.
•Run the ventilator independently.
Notes: (for wireless remote controller)
● Running the ventilator independently is not available.
● No indication on the remote controller.
3.6.4 Seasonal airow function
Seasonal airflow
Select: SELECT
Seasonal airflow
Cooling/Heating
MENU
ON
OFF
RETURN SELECT
HOLD
Seasonal airflow
Select: SELECT
Seasonal airflow
Cooling/Heating
1Select the setting with the [F4]
button.
OFF → Cooling only → Heating
only → Cooling/Heating → OFF…
After changing the setting, press
the [SELECT/HOLD] button to
save the setting.
OFF: The function is disabled.
Cooling only: When the thermostat
turns off during cooling mode, the
vanes move up and down.
Heating only: When the thermostat
turns off during heating mode,
the vanes move to the horizontal
airow direction to circulate the air.
Cooling/Heating: The function is
enabled during both cooling mode
and heating mode.
* In order to enable this function,
the airow direction must be set
to “Auto”.
1Select the desired menu with the
[F1] or [F2] button.
No occupancy energy save
If there are no persons in the room
for 60 minutes or more, energy-
saving operation equal to 2 °C,
4 °F is performed.
Room occupancy energy save
If the occupancy rate decreases
to approximately 30% of the maxi-
mum occupancy rate, energy-
saving operation equal to 1 °C,
2 °F is performed.
No occupancy Auto-OFF
If there are no persons in the
room for the set amount of time
(60–180 minutes), the operation
is automatically stopped.
2When No occupancy energy save
or Room occupancy energy save
is selected
Select the setting with the [F4]
button.
OFF →Cooling only →Heating
only →Cooling/Heating → OFF…
After changing the setting, press
the [SELECT/HOLD] button to
save the setting.
OFF: The function is disabled.
Cooling only: The function is ena-
bled only during cooling mode.
Heating only: The function is ena-
bled only during heating mode.
Cooling/Heating: The function is
enabled during both cooling mode
and heating mode.
3When No occupancy Auto-OFF is
selected
Set the time with the [F3] or [F4]
button.
―: The setting is disabled (the op-
eration will not stop automatically).
60 – 180: The time can be set in
10-minute increments.
4The message at left will appear
if the operation was stopped
automatically by the No occupancy
Auto-OFF setting.
en
RH79A057H01_01en.indd 11 2020/03/17 18:52:57
012

12
4. Operation (For Simple MA remote controller)
4.1. Mode Selection
Pressing the
MODE
button will change the operation mode in the following order.
COOL HEATAUTOFANDRYING SETBACK
*1 *1 *1 *1*1, *2
*1: Not all functions are available on all models of indoor units. Functions that are not available will not appear on the display.
*2: The preset temperature for AUTO (either single or dual set point) mode will appear depending on the indoor unit model.
AUTO (dual set point) mode:
In AUTO (dual set point) mode, the preset temperatures can be set for cooling and heating, and operation can be switched automatically between
cooling and heating depending on the room temperature.
The preset temperatures for cooling and heating set in AUTO (dual set point) mode will be reected to the temperature setting for COOL/DRYING
and HEAT modes.
SETBACK mode:
The SETBACK function automatically switches the operation mode between cooling and heating to maintain the room temperature within the set
temperature range.
The preset temperatures for cooling and heating set in SETBACK mode can be different from the preset temperatures for other modes.
Preset temp.
(COOL)
Preset temp.
(HEAT)
The room temperature
changes corresponding
to the change in the
outside temperature.
Room
temperature
Preset temp.
(COOL)
Preset temp.
(HEAT)
The room temperature
changes corresponding
to the change in the
outside temperature. Room
temperature
During operation in SETBACK mode
HEAT COOL HEAT COOL
HEAT COOL HEAT COOL
During operation in AUTO (dual set point) mode
en
RH79A057H01_01en.indd 12 2020/03/17 18:52:57
013

13
4. Operation (For Simple MA remote controller)
4.2. Temperature setting
In COOL, DRYING, HEAT, and AUTO (single set point) modes
Pressing the
TEMP.
button increases the preset temperature.
Pressing the
TEMP.
button decreases the preset temperature.
In AUTO (dual set point) and SETBACK modes
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
When the
TEMP.
or
TEMP.
button is pressed, the preset temperature (cooling/heating) display blinks.
Cooling preset temperature
Current preset temperature (cooling/heating) appears.
* The example shows the display in AUTO (dual set point) mode.
Heating preset temperature
Current operation mode
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
While the preset temperature (cooling/heating) display blinks, pressing the
TEMP.
button increases the preset temperatures for both
cooling and heating, and pressing the
TEMP.
button decreases the preset temperatures for both cooling and heating.
When the
MODE
button is pressed, only the cooling preset temperature display blinks.
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
While the cooling preset temperature display blinks, pressing the
TEMP.
button increases the cooling preset temperature, and pressing the
TEMP.
button decreases the cooling preset temperature.
When the
MODE
button is pressed, only the heating preset temperature display blinks.
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
While the heating preset temperature display blinks, pressing the
TEMP.
button increases the heating preset temperature, and pressing
the
TEMP.
button decreases the heating preset temperature.
Pressing the
MODE
button completes the preset temperature setting.
* During the preset temperature setting, the setting will automatically turn off if the
TEMP.
or
TEMP.
button is left untouched for a certain period of
time.
en
RH79A057H01_01en.indd 13 2020/03/17 18:52:58
014

14
Preset temperature range is as follows.
Operation mode Preset temperature range
COOL/DRYING 67 - 87 (95)°F/19 - 30 (35)°C
HEAT 63 (40) - 83°F/17 (5) - 28°C
AUTO (single set point) 67 - 83°F/19 - 28°C
AUTO (dual set point) [COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *1, *2
SETBACK [COOL] Preset temperature range for COOL mode.
[HEAT] Preset temperature range for HEAT mode. *2
FAN, VENTI. Unsettable
*1 The preset temperatures for cooling and heating for AUTO (dual set point) mode will be used for those for COOL/DRYING and HEAT mode.
*2 The preset temperatures for cooling and heating can be set under the following conditions.
• The cooling preset temperature is greater than the heating preset temperature.
• The difference between the cooling and heating preset temperatures is equal or greater than the minimum temperature difference that varies depending on the
indoor unit model to be connected.
4.3. Fan speed setting
Pressing the
FAN
button will change the fan speed in the following order.
* The settable fan speed varies depending on the indoor unit model to be connected.
* If the unit has no fan setting function, the fan speed cannot be set.
In this case, the fan icon blinks when the
FAN
button is pressed.
4.4. Vane setting
Pressing the
VANE
button will switch the vane directions.
* The settable vane direction varies depending on the indoor unit model to be connected.
* If the unit has no vane function, the vane direction cannot be set.
In this case, the vane icon blinks when the
VANE
button is pressed.
AUTO
Setting 1AUTO SwingSetting 5Setting 4Setting 3Setting 2
4. Operation (For Simple MA remote controller)
en
RH79A057H01_01en.indd 14 2020/03/17 18:52:58
015

15
5. Timer
■ Timer functions are different by each remote controller.
■ For details on how to operate the remote controller, refer to the appropriate operation manual included with each remote controller.
4. Operation (For Simple MA remote controller)
4.5. Temperature range restriction
The preset temperature range for each operation mode can be restricted.
Room Set to
AUTO COOLHEAT FA N
DRYING VENTI. SETBACK
Room Set to
AUTO COOLHEAT FA N
DRYING VENTI. SETBACK
Room Set to
AUTO COOLHEATFAN
DRYING VENTI. SETBACK
Room Set to
AUTO COOLHEAT FA N
DRYING VENTI. SETBACK
Room Set to
AUTO COOLHEAT FA N
DRYING VENTI. SETBACK
Room Set to
AUTO COOLHEAT FA N
DRYING VENTI. SETBACK
Room Set to
AUTO COOLHEAT FA N
DRYING VENTI. SETBACK
(1)ON/OFF
(3)MODE
(3)
(3)
(3)
(2)FAN
(6)FAN
(4)FAN
(5)TEMP. /
(5)TEMP. /
(5)TEMP. /
(4)FAN
(4)FAN
MODE
MODE
MODE
Press the
ON/OFF
button to stop the air conditioning unit.
Press and hold the
FAN
button for three seconds or longer to bring up the temperature range restriction setting display. (A or B appears.)
Press the
MODE
button to select from A through D.
* When the AUTO (single set point) mode is not available on the indoor unit, or when the AUTO mode is set to OFF in the Mode skip setting, D will
not be displayed.
A. No temperature range restriction:
The temperature range restriction will not be executed for all modes.
B. Temperature range restriction for COOL/DRYING mode:
The preset temperature range for COOL/DRYING, AUTO (dual set point), and SETBACK mode can be changed.
C. Temperature range restriction for HEAT mode:
The preset temperature range for HEAT, AUTO (dual set point), and SETBACK mode can be changed.
D. Temperature range restriction for AUTO (single set point) mode:
The preset temperature range for AUTO (single set point) mode can be changed.
Press the
FAN
button to switch between the upper limit (Hi) and lower limit (Lo) settings.
The air conditioning unit stops.
A. No temperature
range restriction
(Press the button for three seconds or longer.)
(Press the button for three
seconds or longer.)
B. Temperature range restriction for COOL/DRYING mode
C. Temperature range restriction for HEAT mode
D. Temperature range restriction for AUTO (single set point) mode
Upper limit
Lower limit
Upper limit
Upper limit Lower limit
Lower limit
en
RH79A057H01_01en.indd 15 2020/03/17 18:52:59
016

16
6. Care and Cleaning
■Filter information
83
83
Cool
Room
AutoSet temp.
Mode Temp. Fan
Fri will appear on the Main display
in the Full mode when it is time to
clean the lters.
Wash, clean, or replace the lters
when this sign appears.
Refer to the indoor unit Instruc-
tions Manual for details.
Select “Filter information” from the
Maintenance menu, and press the
[SELECT/HOLD] button.
Select “Maintenance” from the Main
menu, and press the [SELECT/
HOLD] button.
Press the [F4] button to reset lter
sign.
Refer to the indoor unit Instructions
Manual for how to clean the lter.
Select “OK” with the [F4] button.
A conrmation screen will appear.
Navigating through the screens
• To go back to the Main menu
....................... [MENU] button
• To return to the previous screen
....................... [RETURN] button
If two or more indoor units are connected, lter cleaning timing for each
unit may be different, depending on the lter type.
The icon will appear when the lter on the main unit is due for
cleaning.
When the lter sign is reset, the cumulative operation time of all units
will be reset.
The icon is scheduled to appear after a certain duration of operation,
based on the premise that the indoor units are installed in a space with
ordinary air quality. Depending on the air quality, the lter may require
more frequent cleaning.
The cumulative time at which lter needs cleaning depends on the model.
• This indication is not available for wireless remote controller.
Caution:
• Ask authorized people to clean the lter.
► Cleaning the lters
• Clean the lters using a vacuum cleaner. If you do not have a vacuum
cleaner, tap the lters against a solid object to knock off dirt and dust.
• If the lters are especially dirty, wash them in lukewarm water. Take care
to rinse off any detergent thoroughly and allow the lters to dry completely
before putting them back into the unit.
Caution:
• Do not dry the lters in direct sunlight or by using a heat source,
such as an electric heater: this may warp them.
• Do not wash the lters in hot water (above 50 °C, 122 °F), as this
may warp them.
• Make sure that the air lters are always installed. Operating the
unit without air lters can cause malfunction.
Caution:
• Before you start cleaning, stop operation and turn OFF the power
supply.
• Indoor units are equipped with lters to remove the dust of sucked-
in air. Clean the lters using the methods shown in the following
sketches.
When the is displayed on the
Main display in the Full mode, the
system is centrally controlled and
the lter sign cannot be reset.
Main Main menu
Maintenance
MENU
ON
OFF
RETURN SELECT
HOLD
Main menu: RETURN
Cursor
Maintenance menu
Error information
Filter information
Cleaning
MENU
ON
OFF
RETURN SELECT
HOLD
Main menu: MENU
Reset
Filter information
Press Reset button after
filter cleaning.
Please clean the filter.
MENU
ON
OFF
RETURN SELECT
HOLD
83
83
Fri
Room
Set temp.
Mode Temp. Fan
Cool Auto
OKCancel
Filter information
Reset filter sign?
Main menu: MENU
Filter information
Filter sign reset
MENU
ON
OFF
RETURN SELECT
HOLD
en
RH79A057H01_01en.indd 16 2020/03/17 18:52:59
017

17
7. Trouble Shooting
Having trouble? Here is the solution. (Unit is operating normally.)
Air conditioner does not heat or cool well. Clean the lter. (Airow is reduced when the lter is dirty or clogged.)
Check the temperature adjustment and adjust the set temperature.
Make sure that there is plenty of space around the outdoor unit. Is the
indoor unit air intake or outlet blocked?
Has a door or window been left open?
When heating operation starts, warm air does not blow from the indoor
unit soon. Warm air does not blow until the indoor unit has sufciently warmed up.
During heating mode, the air conditioner stops before the set room tem-
perature is reached. When the outdoor temperature is low and the humidity is high, frost
may form on the outdoor unit. If this occurs, the outdoor unit performs
a defrosting operation. Normal operation should begin after approxi-
mately 10 minutes.
Airow direction changes during operation or airow direction cannot be
set. During cooling mode, the vanes automatically move to the horizontal
(down) position after 1 hour when the down (horizontal) airow direc-
tion is selected. This is to prevent water from forming and dripping from
the vanes.
During heating mode, the vanes automatically move to the horizontal
airow direction when the airow temperature is low or during defrost-
ing mode.
When the airow direction is changed, the vanes always move up and
down past the set position before nally stopping at the position. When the airow direction is changed, the vanes move to the set posi-
tion after detecting the base position.
A owing water sound or occasional hissing sound is heard. These sounds can be heard when refrigerant is owing in the air condi-
tioner or when the refrigerant ow is changing.
A cracking or creaking sound is heard. These sounds can be heard when parts rub against each due to ex-
pansion and contraction from temperature changes.
The room has an unpleasant odor. The indoor unit draws in air that contains gases produced from the
walls, carpeting, and furniture as well as odors trapped in clothing, and
then blows this air back into the room.
A white mist or vapor is emitted from the indoor unit. If the indoor temperature and the humidity are high, this condition may
occur when operation starts.
During defrosting mode, cool airow may blow down and appear like a
mist.
Water or vapor is emitted from the outdoor unit. During cooling mode, water may form and drip from the cool pipes and
joints.
During heating mode, water may form and drip from the heat exchanger.
During defrosting mode, water on the heat exchanger evaporates and
water vapor may be emitted.
The operation indicator does not appear in the remote controller display.
Turn on the power switch. “ ” will appear in the remote controller display .
The air conditioner does not operate even though the ON/OFF button is
pressed. The operation mode display on the remote controller disappears. Is the power switch of the indoor unit turned off? Turn on the power
switch.
“
CENTRAL
” appears in the remote controller display.
(For Simple MA Remote controller)
During central control, “
CENTRAL
” appears in the remote controller
display and air conditioner operation cannot be started or stopped us-
ing the remote controller.
When restarting the air conditioner soon after stopping it, it does not
operate even though the ON/OFF button is pressed. Wait approximately three minutes.
(Operation has stopped to protect the air conditioner.)
Air conditioner operates without the ON/OFF button being pressed. Is the on timer set?
Press the ON/OFF button to stop operation.
Is the air conditioner connected to a central remote controller?
Consult the concerned people who control the air conditioner.
Does “ ” or “
CENTRAL
” appear in the remote controller display?
Consult the concerned people who control the air conditioner.
Has the auto recovery feature from power failures been set?
Press the ON/OFF button to stop operation.
Air conditioner stops without the ON/OFF button being pressed. Is the off timer set?
Press the ON/OFF button to restart operation.
Is the air conditioner connected to a central remote controller?
Consult the concerned people who control the air conditioner.
Does “ ” or “
CENTRAL
” appear in the remote controller display?
Consult the concerned people who control the air conditioner.
“
HO
” appears in the remote controller display.
(For Simple MA Remote controller)
The initial settings are being performed. Wait approximately 3 minutes.
An error code appears in the remote controller display. The protection devices have operated to protect the air conditioner.
Do not attempt to repair this equipment by yourself.
Turn off the power switch immediately and consult your dealer. Be sure
to provide the dealer with the model name and information that ap-
peared in the remote controller display.
Draining water or motor rotation sound is heard. When cooling operation stops, the drain pump operates and then
stops. Wait approximately 3 minutes.
en
RH79A057H01_01en.indd 17 2020/03/17 18:52:59
018

18
7. Trouble Shooting
Range of application
The range of working temperatures for both the indoor and outdoor units of the series Y, R2, Multi-S is as below.
Caution:
The use of your air conditioner outside the range of working temperature and humidity can result in serious failure.
Mode Indoor unit Outdoor unit
PUHY PURY PUMY
Cooling 15 °C - 24 °C, 59 °F - 75 °F WB –5 °C - 46 °C, 23 °F - 115 °F DB –5 °C - 46 °C, 23 °F - 115 °F DB –5 °C - 46 °C, 23 °F - 115 °F DB
Heating 15 °C - 27 °C, 59 °F - 81 °F DB –20 °C - 15.5 °C, –4 °F - 60 °F WB –20 °C - 15.5 °C, 10 °F - 60 °F WB –18 °C - 15.5 °C, 0 °F - 60 °F WB
Note: As an applicable humidity standard for both indoors and outdoors, we recommend use within a range of 30 - 80% relative humidity.
Warning:
If the air conditioner operates but does not cool or heat (depending on model) the room, consult your dealer since there may be a refrigerant
leak. Be sure to ask the service representative whether there is refrigerant leakage or not when repairs are carried out.
The refrigerant charged in the air conditioner is safe. Refrigerant normally does not leak, however, if refrigerant gas leaks indoors and comes
into contact with the re of a fan heater, space heater, stove, etc., harmful substances will be generated.
Having trouble? Here is the solution. (Unit is operating normally.)
“ ” appears in the remote controller display.
(For Wired Remote controller)
During central control, “ ” appears in the remote controller display
and air conditioner operation cannot be started or stopped using the
remote controller.
Remote controller timer operation cannot be set.
(For Wired Remote controller)
Are timer settings invalid?
If the timer can be set, or appears in the remote controller
display.
Noise is louder than specications. The indoor operation sound level is affected by the acoustics of the
particular room as shown in the following table and will be higher than
the noise specication, which was measured in an echo-free room.
High sound
absorbing rooms
Normal rooms Low sound
absorbing rooms
Location
examples
Broadcasting
studio, music
room, etc.
Reception room,
hotel lobby, etc.
Ofce, hotel
room
Noise levels 3 to 7 dB 6 to 10 dB 9 to 13 dB
Nothing appears in the wireless remote controller display, the display
is faint, or signals are not received by the indoor unit unless the remote
controller is close.
The batteries are low.
Replace the batteries and press the Reset button.
If nothing appears even after the batteries are replaced, make sure
that the batteries are installed in the correct directions (+, –).
The operation lamp near the receiver for the wireless remote controller
on the indoor unit is ashing. The self diagnosis function has operated to protect the air conditioner.
Do not attempt to repair this equipment by yourself.
Turn off the power switch immediately and consult your dealer. Be sure
to provide the dealer with the model name.
Warm air blows from the indoor unit intermittently when heating mode is
off or during fan mode. When another indoor unit is operating in heating mode, the control
valve opens and closes occasionally to maintain stability in the air
conditioning system. This operation will stop after a while.
* If this will cause an undesirable rise in the room temperature in small
rooms, etc., stop the operation of the indoor unit temporarily.
en
RH79A057H01_01en.indd 18 2020/03/17 18:52:59
019

19
8. Specications
PLFY-EP∙NEMU-E / PLFY-EP∙NEMU-E1 Series
Model PLFY-EP06NEMU-E PLFY-EP08NEMU-E PLFY-EP12NEMU-E PLFY-EP15NEMU-E
Power source Single 208/230 V 60Hz
Capacity Cooling <BTU/h> 6,000 8,000 12,000 15,000
Heating <BTU/h> 6,700 9,000 13,500 17,000
Dimension Height <inch> 10-3/16 (1-9/16)
Width <inch> 33-1/16 (37-13/32)
Depth <inch> 33-1/16 (37-13/32)
Net weight <lbs> 46 (11)
Fan Airow range
(Low-Middle2-Middle1-High) <CFM> 300-424-459-494 494-530-565-600 494-530-565-600 530-547-565-600
Noise level
(Low-Middle2-Middle1-High) <dB> 19-23-25-27 27-29-30-31 27-29-30-31 28-29-30-31
Model PLFY-EP18NEMU-E1 PLFY-EP24NEMU-E PLFY-EP30NEMU-E PLFY-EP36NEMU-E PLFY-EP48NEMU-E
Power source Single 208/230 V 60Hz
Capacity Cooling <BTU/h> 18,000 24,000 30,000 36,000 48,000
Heating <BTU/h> 20,000 27,000 34,000 40,000 54,000
Dimension Height <inch> 11-3/4 (1-9/16)
Width <inch> 33-1/16 (37-13/32)
Depth <inch> 33-1/16 (37-13/32)
Net weight <lbs> 55 (11)
Fan Airow range
(Low-Middle2-Middle1-High) <CFM> 636-671-742-812 636-671-742-812 636-706-777-812 777-883-989-1095 777-953-1095-1236
Noise level
(Low-Middle2-Middle1-High) <dB> 28-30-32-34 28-30-32-34 28-31-33-35 35-37-39-41 36-39-42-45
Notes:
1 Cooling/Heating capacity indicates the maximum value at operation under the following condition.
Cooling: Indoor 27 °C DB, 81 °F DB/19 °C WB, 66 °F WB, Outdoor 35 °C DB, 95 °F DB
Heating: Indoor 20 °C DB, 68 °F DB, Outdoor 7 °C DB, 45 °F DB/6 °C WB, 43 °F WB
2 This gure ( ) indicates panel’s.
en
RH79A057H01_01en.indd 19 2020/03/17 18:53:00
020