Mitsubishi Electric plfy-p vcm-e3 User manual
English (GB)
Deutsch (D)
Français (F)
Nederlands (NL)
Español (E)
Italiano (I)
Português (P)
For safe and correct use, please read this installation manual thoroughly before installing the air-conditioner
unit.
Zum sicheren und ordnungsgemäßen Gebrauch der Klimaanlage das Installationshandbuch gründlich durch-
lesen.
Veuillez lire le manuel d’installation en entier avant d’installer ce climatiseur pour éviter tout accident et vous
assurer d’une utilisation correcte.
INSTALLATIEHANDLEIDING
Voor een veilig en juist gebruik moet u deze installatiehandleiding grondig doorlezen voordat u de airconditioner
installeert.
Per un uso sicuro e corretto, leggere attentamente questo manuale di installazione prima di installare il condiziona-
tore d’aria.
Para un uso seguro y correcto, lea detalladamente este manual de instalación antes de montar la unidad de
aire acondicionado.
Para segurança e utilização correctas, leia atentamente este manual de instalação antes de instalar a unidade
de ar condicionado.
PLFY-P
GB
-
tions”.
Warning:
death to the user.
Describes precautions that must be observed to prevent damage to the unit.
After installation work has been completed, explain the “Safety precautions,” use, and
maintenance of the unit to the customer according to the information in the Operation
Manual and perform the test run to ensure normal operation. Both the Installation
Manual and Operation Manual must be given to the user for keeping. These manuals
must be passed on to subsequent users.
Warning:
an authorized technician to install them.
The appliance shall be installed in accordance with national wiring regulations.
1. Safety precautions.....................................................................................2
2. Installing the indoor unit ............................................................................2
3. Refrigerant pipe and drain pipe.................................................................4
4. Electrical work ...........................................................................................6
5. Installing the grille......................................................................................9
6. Test run.................................................................................................... 11
: Indicates an action that must be avoided.
: Indicates that important instructions must be followed.
: Indicates a part which must be grounded.
: Indicates that caution should be taken with rotating parts.
: Indicates that the main switch must be turned off before servicing.
: Beware of electric shock.
: Beware of hot surface.
: At servicing, please shut down the power supply for both the Indoor and
Outdoor Unit.
Warning:
-
ant.
or artwork are kept.
The indoor unit should be supplied with the following accessories.
Accessory name Q’ty
1Installation template 1
2Washers (with insulation)
Washers (without insulation)
4
4
3
Pipe cover (for refrigerant piping joint)
small diameter (liquid)
large diameter (gas)
1
1
4Band (large)
Band (small)
6
2
5Screw with washer (M5 u25) for mounting grille 4
6Drain socket 1
7Insulation 1
8Wireless junction cable 1
1
23
4657
8
Note:
GB
accessory with the grille), make an opening in the ceiling so that the main unit can
be installed as shown in the diagram. (The method for using the template and the
gauge are shown.)
* Before using, check the dimensions of template and gauge, because they
change due to fluctuations of temperature and humidity.
* The dimensions of ceiling opening can be regulated within the range shown in
following diagram; so center the main unit against the opening of ceiling, en-
suring that the respective opposite sides on all sides of the clearance between
them becomes identical.
* Suspension bolts are to be procured at the field.
AOuter side of main unit
BBolt pitch
CCeiling opening
DOuter side of Grille
EGrille
FCeiling
G
If setting the maintenance space for G, be
HMaintenance space
IFresh air intake
JAngle
KElectric component box
to 15 mm to be left.
* Leave the maintenance space at the electric component box end.
when outside air is taken.
u
screws which should be prepared locally.
wrap the duct in a heat insulate to avoid causing dew drop on the wall.
ADuct flange recommended shape
B3-ø5 hole
CDetail drawing of fresh air intake
DIndoor unit
ECeiling surface
F
Gø73.4 cutout hole
HDuct flange (Prepared locally)
I4 u
JDuct
-
structors and interior decorators should be consulted for details.
(1) Extent of ceiling removal: The ceiling must be kept completely horizontal and the
ceiling foundation (framework: wooden slats and slat holders) must be reinforced
in order to protect the ceiling from vibration.
(2) Cut and remove the ceiling foundation.
(3) Reinforce the ends of the ceiling foundation where it has been cut and add ceiling
foundation for securing the ends of the ceiling board.
(4) When installing the unit on a slanting ceiling, interlock a pillow between the ceiling
and the grille and set so that the unit is installed horizontally.
1Wooden structures
as reinforcing members.
with the unit.)
2Ferro-concrete structures
Secure the suspension bolts using the method shown, or use steel or wooden hang-
ers, etc. to install the suspension bolts.
AUnit
BGrille
CPillow
DCeiling
ERafter
FBeam
GRoof beam
H
each (procure locally)
I
locally)
JSteel reinforcing rod
12
A(mm)
C
(mm)
*B: Suspension bolt pitch (see Fig. 2-2 Bfor details)
ø75
15
25
ø
92
27+5
GB
ADrain pipe
BCeiling
CGrille
DRefrigerant pipe (liquid)
ERefrigerant pipe (gas)
FWater supply inlet
GMain unit
A Flare cutting dimensions
ASuspension bolt (Procure locally)
BCeiling
CNut (Procure locally)
DWasher (with insulation) (Accessory)
Suspend the main unit as shown in the diagram.
1. In advance, set the parts onto the suspension bolts in the order of the washers
(with insulation), washers (without insulation) and nuts (double).
(with insulation) and nuts (double) are to be set later.
2. Lift the unit to the proper height of the suspension bolts to insert the mounting
plate between washers and then fasten it securely.
3. When the main unit can not be aligned against the mounting hole on the ceiling,
it is adjustable owing to a slot provided on the mounting plate. (Fig. 2-6)
failing to adhere to this range.
properly aligned with the opening of the ceiling. Be sure to confirm this, otherwise
condensation may form and drip due to air leakage etc.
with water.
securely to fasten the main unit.
entering the main unit when the grilles are left unattached for a while or when the
ceiling materials are to be lined after installation of the unit is finished.
* As for the details of fitting, refer to the instructions given on the Installation tem-
plate.
EMounting plate
FWasher (without insulation) (Accessory)
GCheck using the Installation gauge
AMain unit
BCeiling
CGauge (Grille accessory)
DCeiling opening dimensions
As viewed from A
thickness of 12 mm or more).
-
flare nut.
carefully.
AMain unit
BCeiling
CInstallation template (Accessory)
DScrew with washer (Accessory)
Copper pipe O.D.
(mm)
Flare dimensions
øA dimensions (mm)
ø6.35
ø9.52
ø12.7 16.2 - 16.6
19.3 - 19.7
22.9 - 23.3
27+5
93
øA
Warning:
-
ing the compressor.
GB
more downward slope.
1Correct piping
2Wrong piping
AInsulation (9 mm or more)
B
CSupport metal
KAir bleeder
LRaised
MOdor trap
Grouped piping
DO.D. ø32 PVC TUBE
EMake it as large as possible
FIndoor unit
GMake the piping size large for grouped piping.
H
I
(9 mm or more insulation)
J
1. Connect the drain socket (supplied with the unit) to the drain port. (Fig. 3-5)
(Affix the tube using PVC adhesive then secure it with a band.)
2. Install a locally purchased drain pipe (PVC pipe, O.D. ø32).
(Affix the pipe using PVC adhesive then secure it with a band.)
3. Insulate the tube and pipe. (PVC pipe, O.D. ø32 and socket)
4. Check that drain flows smoothly.
5. Insulate the drain port with insulating material, then secure the material with a
band. (Both insulating material and band are supplied with the unit.)
AUnit
BInsulating material
CBand (large)
DDrain port (transparent)
EInsertion margin
FMatching
GDrain pipe (O.D. ø32 PVC TUBE)
HInsulating material (purchased locally)
ITransparent PVC pipe
J
KBand (small)
LDrain socket
B
C Apply refrigerating machine oil over the entire flare seat surface.
(mm)
1Wrap the enclosed large-sized pipe cover around the gas pipe, making sure that
the end of the pipe cover touches the side of the unit.
2Wrap the enclosed small-sized pipe cover around the liquid pipe, making sure that
the end of the pipe cover touches the side of the unit.
3Secure both ends of each pipe cover with the enclosed bands. (Attach the bands
connections for gas leakage with nitrogen gas. (Check that there is no refrigerant
leakage from the refrigerant piping to the indoor unit.)
ARefrigerant pipe and insulating material
(Procure locally)
BPipe cover (large) (Accessory)
CPipe cover (small) (Accessory)
DRefrigerant pipe (gas)
ERefrigerant pipe (liquid)
FBand (Accessory)
GCross-sectional view of connection
HRefrigerant pipe
IInsulating material
JSqueeze
Flare nut O.D.
Liquid pipe Gas pipe Liquid pipe Gas pipe
Pipe size
(mm)
Tightening
torque
(N·m)
Pipe size
(mm)
Tightening
torque
(N·m)
Pipe size
(mm)
Tightening
torque
(N·m)
Pipe size
(mm)
Tightening
torque
(N·m)
Liquid
pipe
(mm)
Gas
pipe
(mm)
49 - 61 49 - 61 17 26
49 - 61* 49 - 61 17 26
34 - 42 34 - 42 22 29
34 - 42 34 - 42 22 29
Max. 15cm
1.5~2m
1
2
GB
1.Remove 2 screws to detach the electric component cover.
2.Route each cable through the wiring intake into the electric component box. (Procure
power supply cable and control cable locally.)
3.Securely connect the power supply cable and control cable to the terminal
blocks.
4.Secure the cables with clamps outside the electric component box.
5.Attach the electric component cover as it was.
Always install earth.
(Earth cable dia: Thicker than 1.6 mm)
bushing for tensile force. (PG connection or the like.)
AElectric component cover
BElectric component box
CEntry for power supply cable
DEntry for remote control cable and trans-
mission cable
ECable clamp
FPower supply terminals (L, N, )
GTransmission terminals (M1, M2, S)
HMA Remote controller terminal (1. 2)
IIndoor controller
JRemote control cable
KTransmission cable
LPower supply cable
IEC57, 245 IEC 53 or 227 IEC 53.
provided by the air conditioner installation.
A
Ground-fault interrupter
B
C
Indoor unit
D
Pull box
Warning:
55 mm
12 mm
■
(1) Take out the wireless junction cable that is supplied with the accessories.
(2) Route the indoor controller board connector (white) of the wireless junction cable
through the main unit BUSH in the direction indicated by the arrow. (Fig. 4-2)
(3) Route the wireless junction cable through the electric component box BUSH, and
(4) Secure the cables and wires with the clamp.
AWireless junction cable (Accessory)
BMain unit BUSH
CElectric component box
DElectric component box BUSH
EClamp
FIndoor controller board
CCCCC
AB D
~220-240V
D
C
TB2 TB5 TB15
S12
M1
LN
M2
AB
~220-240V
JKL
L
GB
6000
600
60
10
Tripping Time [s]
1
0.1
0.01
12
Rated Tripping current (x)
34 68
C
10 20
SAMPLE
Sample chart
Types of transmission cable Shielding wire CVVS or CPEVS
Cable diameter More than 1.25 mm2
Length
Types of remote control cable
Shielding wire MVVS
Cable diameter 2
Length
the longest allowable transmission cable
Types of remote control cable 2-core cable (unshielded)
Cable diameter 2
Length
Total operating current of the indoor
unit
Minimum wire thickness (mm²) Ground-fault interrupter *1 Local switch (A) Breaker for wiring
(NFB)
Main cable Branch Ground Capacity Fuse
1.5 1.5 1.5 16 16
2.5 2.5 2.5 25 25
32 32
*1 The Ground-fault interrupter should support inverter circuit.
The Ground-fault interrupter should combine using of local switch or wiring breaker.
Indoor unit V1 V2
Type 1 PLFY-VBM, PMFY-VBM, PEFY-VMS,
PCFY-VKM, PKFY-VHM, PKFY-VKM, PLFY-VCM 2.4
Type 2 PEFY-VMA 1.6
Type 3 PEFY-VMHS
Others Other indoor unit
Please pick up "C" from the tripping characteristic of the breaker.
<Example of "F2" calculation>
*3 Current sensitivity is calculated using the following formula.
G1 Current sensitivity
Wire thickness V3
1.5 mm2
2.5 mm256
266
8
GB
indoor unit TB5 is a shielding wire connection. For specifications about the con-
necting cables, refer to the outdoor unit installation manual.
-
ler.
2
2junction cable.
1MA Remote controller
2-wire)
2M-NET Remote controller
(Nonpolarized 2-wire)
3Wireless remote controller (When installing wireless signal receiver)
troller board.
controller, connect TB15 each with the same number.
controller. (In the default setting of indoor unit and wireless remote controller, Pair
ATerminal block for indoor transmission cable
BTerminal block for outdoor transmission cable (M1(A), M2(B), (S))
CRemote controller
DWireless signal receiver
EWireless remote controller
(Be sure to operate with the main power turned OFF.)
1How to set addresses
(for 1 to 9) with “3”.
2How to set branch numbers SW14 (Series R2 only)
Match the indoor unit’s refrigerant pipe with the BC controller’s end connection
number.
can be used to set unit addresses and branch numbers at will.
referring to the Data Book.
in a remote controller
If you want to sense room temperature with the built-in sensor in a remote controller,
necessary also makes it possible to adjust the air flow at a time when the heating
thermometer is OFF.
1
2
3
Model Power supply IFM
MCA (A) Output (kW) FLA (A)
PLFY-P15VCM-E3
Max.: 264V
PLFY-P25VCM-E3
PLFY-P32VCM-E3
IFM: Indoor Fan Motor Output: Fan motor rated output
(BRANCH No.) (1s DIGIT)
9
GB
grille.
pipe area and at the opposite corner) as shown in the diagram.
AMain unit
BDetailed diagram of installed screw with washer (accessory).
then temporarily secure the grille using the bell shaped holes.
* Make sure that the lead wiring of the grille does not get pinched between the
grille and the main unit.
AMain unit
BElectric component box
CScrew with washer (for temporary use)
DScrew with washer (Accessory)
EGrille
FBell shaped hole
GReceiver (for SLP-2ALW)
(with captive washer) as well as the two remaining screws (with captive washer).
* Make sure that there are no gaps between the main unit and the grille or the
grille and the ceiling.
ACeiling
BMain unit
CGrille
DMake sure that there are no gaps.
(mm)
relative to the ceiling. If the unit is not properly positioned in the ceiling, there may
-
rectly.
576 uu
to adhere to this range.
AMain unit
BCeiling
CGauge (Accessory)
DCeiling opening dimensions
1to open the intake grille.
* Do not unlatch the hook for the intake grille.
from the grille as indicated by the arrow 2.
indicated by the arrow 1to remove the corner panel.
AIntake grille
BGrille
CIntake grille levers
DGrille hook
EHole for the grille’s hook
FCorner panel
GScrew
Accessory name Q’ty Remark
1Grille 1 u
2Screw with washer 4 M5 uu25 (mm)
3Gauge 1
4Fastener 2
5Band 2
1
45
23
When tightening the screw with captive washer 2
GB
The vanes of the unit can be set and locked in up or down orientations depending
upon the environment of use.
performed using the remote controller. In addition, the actual position of the vanes
may differ from the position indicated on the remote controller.
1Turn off the main power switch.
Injuries and or an electrical shock may occur while the fan of the unit is rotating.
2Disconnect the connector for the vane motor of the vent that you want to lock.
(While pressing the button, remove the connector in the direction indicated by
the arrow as shown in the diagram.) After removing the connector, insulate it with
tape.
3
direction
A (mm) 21 25
AButton
BVane motor
C
DConnector
EMeasurement standard
position of grille
F
reverse order to install the intake grille and the corner panel.
ARefrigerant piping of the main unit
BDrain piping of the main unit
CCorner panel
* Installation in any position is possible.
DPosition of the levers on the intake grille when sent from the factory.
* Although the clips can be installed in any of four positions.
EReceiver (for SLP-2ALW)
and the surface of the ceiling. If there is any gap between the unit and the grille, or
between the grille and the surface of the ceiling, it may cause dew to collect.
-
tach the white glass tube that comes with the main unit so that the tube covers the
connector. Close the opening of the glass tube with the band.
AFastener (Accessory)
BWhite glass tube
CConnector of the main unit
DConnector of the grille
EBand (Accessory)
FReceiver (for SLP-2ALW)
GB
The following 3 methods are available.
-
nals.
Warning:
Function buttons
432 1
5
6
789 0
1
2
Press to save the setting.
3
Press to return to the previous screen.
4
Press to bring up the Main menu.
5
Operation settings will appear.
When the backlight is off, pressing any button turns the backlight on and it will
stay lit for a certain period of time depending on the screen.
When the backlight is off, pressing any button turns the backlight on and does
6
This lamp lights up in green while the unit is in operation. It blinks while the
remote controller is starting up or when there is an error.
7
Main display: Press to change the operation mode.
Main menu: Press to move the cursor down.
8
Main display: Press to decrease temperature.
Main menu: Press to move the cursor up.
9
Main display: Press to increase temperature.
Main menu: Press to go to the previous page.
0
Main display: Press to change the fan speed.
Main menu: Press to go to the next page.
1Select “Service” from the Main menu, and press the button.
2When the Service menu is selected, a window will appear asking for the password. (Fig. 6-2)
To enter the current maintenance password (4 numerical digits), move the cursor to the digit you want to change with the F1 or F2 button, and set each number
F3 or F4 button. Then, press the button.
Note: The initial maintenance password is “9999”. Change the default password as necessary to prevent unauthorized access.
Have the password available for those who need it.
Note: If you forget your maintenance password, you can initialize the password to the default password “9999” by pressing and
holding the F1 and F2 buttons simultaneously for three seconds on the maintenance password setting screen.
3Select “Test run” with the F1 or F2 button, and press the button. (Fig. 6-3)
4Select “Test run” with the F1 or F2 button, and press the button. (Fig. 6-4)
F1 F2 F3 F4
unemecivreS
rosruC
:unemniaM
Test run
Input maintenance info.
Function setting
Check
Self check
F1 F2 F3 F4
Test run menu
Cursor
Service menu:
Test run
Drain pump test run
F1 F2 F3 F4
Service menu
Cursor
Select:
Enter maintenance password
GB
is leaking from joints.
-
a water supply pump etc. During this process, be careful not to spray water into
the drain pump mechanism.
(2) Confirm that water is being drained out through the drainage outlet, after switching
over from remote control mode to trial run mode.
(3) After checking the drainage, ensure that the cover is replaced and the power
supply is isolated.
(4) After confirming the drainage system is functioning, replace the drain plug.
AInsert the pump end 3 to 5 cm
BCover of water supply inlet
C
DWater
EDrain plug
1Turn on the power to the unit at least 12 hours before the test run.
2Press the button twice continuously.
(Start this operation from the status of remote controller display turned off.)
Aand current operation mode are displayed.
3Press the button to activate mode, then check whether
cool air is blown out from the unit.
4Press the button to activate mode, then check whether
warm air is blown out from the unit.
5Press the button and check whether fan speed changes.
6Press the button and check whether the auto vane operates properly.
7
Note:
steps 2to 7.
Test run
F1 F2 F3 F4
Cool
Pipe
Auto
Switch disp.
Mode Fan
RemainTest run
F1 F2 F3 F4
Remain
Vane
1Press the F1 button to go through the operation modes in the order of “Cool”
and “Heat”. (Fig. 6-5)
Cool mode: Check the cold air blow off.
Heat mode: Check the heat blow off.
* Check the operation of the outdoor unit’s fan.
2Press the button and open the Vane setting screen.
1Check the auto vane with the F1 F2 buttons. (Fig. 6-6)
2Press the button to return to “Test run operation”.
3Press the button.
101
RU
*+,+,*-*.+-/+.+-
*+0*
0*+1-2,+*
3*+*,4*,3**43*+-
*-*2++5
++0
.*+.+*+0*,6.+*+4
-*+.2,*
*+0
.*+.+*+0*,6.+*+4
+0+,+
-
+0
++0
,+**+89+*6.
*9+6
:+4***.+*+4+,+
**+,+*,.+0*2
*+.,,*-*,0-
.-.**.2*
,6*+2*9,-
13*6*+90*+*+2+2+1
****.+0**+.
*++5*;6*,+4*
+-9**
+***,
**9+2*+9+.
**
3*++,*.0..*89+.3*+-
14***14191****.+*
* ,6.* *** *14
+3*+,*
+0.,**0,.*
96,*+*+.2*9
,14,689
9+* ,54,6
+*+. +*+49*+962*.5
,.6+-*-62*
.+,.2+*+.6*2***+.+.*
+*4*4*10+++-**
+*0+4*0+,09+
**.62**+,-
+62*5*2+262*
*-6*+,+6
-6*+,+60*..*-
+***+.60*+*+.+2+0
1,2 62**-2*2 3*
*..*6-+0,+,**.
.6*+**+65-3*0*0*
++2+,-1,+,*.3*2
101
101
103
105
108
110
/+.+*+0*
-
++0
*+-****3**622+,+
*+0
+62***-
*.+*+,.62*
*38+,,56-*6
-*60142.+*+,.689.6
*+,.6+62*
*9+6*6+0+*-
560*.6+**-.6+,++**
*9+6,.66
:*+,+
**++.*9*+,*
**,**-4*+0
*++.*9+6+*4*
+*.1-*+.+
+**+,62*++,*.+
.1-+,+
*9+62+.5*.
*1-**.1-+,+
**+2+,+
++* -*.6+-
0**++,+
-
-
1 1
2
4
4
3
1
1
4
6
2
5
4
6 1
7 1
8 1
1
23
4657
8
+-
3*+*1+*8++**92+****92+-
+26*6*92++*+**+*-.*+6-
43*6+,6
102
RU
0*+**.6
,*
-
-
-
**+2+,+
A
B
C
D
E
F
G
-
G
H
I
J
K
-
**92+
026
*+0
**+9+6
-***+,**
29+6+026
1-***+*0*+*-
1*
2*892***
s
*89
s
u
**92,62***
s-
A
Bø5
C -
D
E
Fø
Gø
H
Iu
J
*+9,-*+-*
*5
-
-
-
1
-
2
A
B
C
D
E
F
G
H
I-
J
12
A
C
B
120°
120°
ø100
30°
15
20
25
120°
120°
ø
100
208
+5
0
RU
+,62*+0*+,
0*+,62*+0.6
*+,*+2,
A
B
C
D
E
F
G
A
**+2+,+
A
B
C
D-
+5+,+
-
s
s-
-
-
+++022+,+
*2.6,*
-
-
E
F-
G
A
B
C-
D
*+,
-
A
B
C-
D-
+5
0
++0
+*+,+0**+,.-601-
40*++
RU
+,62*+0*+,
+0.*+,.
ø-
1
2
A
B
C
K
L
M
D ø
E
F
G
H
I ø
J
ø
ø
A
B
C
D
E
F
G ø
H
I
Jø
K
L
B
C -
*++,+
9*+,62*
1
2
3-
-
A-
B -
C -
D
E
F
G
H
I
J
26
26
22
22
30 30 30
1
2
RU
<*+-+,*.
*++,+
-
-
A
B
C
D-
E
F
G
H-
I
J
K
L
■+,+.+2
**,,+21-
,*.1452+*2-
2+,+
-
A
B
C
D
E
F
CCCCC
AB D
~220-240V
D
C
TB2 TB5 TB15
S12
M1
LN
M2
AB
~220-240V
+
-
-
A
B
C
D
++0
JKL
L
2*6*,*-
.,52*<*0*+*.1-
2+1+*
RU
<*+-+,*.
.,+
9.,
2
,*92+/
2
,*92+/
-
2
-
16 16 20
25 25 30
32 32 40
38
0 0
248
256
266
6000
600
60
10
1
0,1
0,01
12
34 68
C
10 20
=:>
RU
**92+-
,+-*++0
-
-
2
2
1
2
3-
-
A
B
C
D
E
*+
1
-
2
-
-
+*+*+.*+*.-
41*-*+2**9-
2+
1
2
3
<*+-+,*.
<*+-6+*+*
108
RU
*+5*
2*
A
B
+**9+5*
-
A
B
C
D
E
F
G
+*9+5*
-
A
B
C
D
**9+5*
2***9+5*-
uu
-
A
B
C
D
6,++5*
s1
s
*
s
2
2
s
1
A
B
C
D
E
++*+0*+5*
1 1 u
24 uu
3 1
4 2
5 2
F
G
15~20
1
45
23
*+0
:*2*+0,-*5,2*+.*
*,2*+.2?+*
<*0*+*+01*
Table of contents
Other Mitsubishi Electric Air Conditioner manuals
Mitsubishi Electric
Mitsubishi Electric Mr. Slim PKH-2.5 3FKHA User manual
Mitsubishi Electric
Mitsubishi Electric Mr.Slim MUZ-FD09NA-U1 User manual
Mitsubishi Electric
Mitsubishi Electric Mr.Slim MFZ-KA12NA Installation and user guide
Mitsubishi Electric
Mitsubishi Electric Mr. Slim MS-A09WA User manual
Mitsubishi Electric
Mitsubishi Electric PAA-A18AA1 User manual
Mitsubishi Electric
Mitsubishi Electric PUMY-P-NKMU User manual
Mitsubishi Electric
Mitsubishi Electric JG79A476H01 User manual
Mitsubishi Electric
Mitsubishi Electric ECODAN EHSC Series User manual
Mitsubishi Electric
Mitsubishi Electric Mr.Slim PUZ-A NHA6 Series User manual
Mitsubishi Electric
Mitsubishi Electric CITY MULTI PQRY-P200YMF-B How to use
Mitsubishi Electric
Mitsubishi Electric Mr. SLIM PEAD-M50JAA(D) User manual
Mitsubishi Electric
Mitsubishi Electric MSZ-FE09NA-8 User manual
Mitsubishi Electric
Mitsubishi Electric PKA-RP FAL User manual
Mitsubishi Electric
Mitsubishi Electric PLA-RP User manual
Mitsubishi Electric
Mitsubishi Electric MSZ-AP25VG User manual
Mitsubishi Electric
Mitsubishi Electric Mr. Slim MS-A09WA User manual
Mitsubishi Electric
Mitsubishi Electric PKFY-P-VKM-E User manual
Mitsubishi Electric
Mitsubishi Electric PUMY-P112VKM3 Operating manual
Mitsubishi Electric
Mitsubishi Electric MSZ-GS18NA User manual
Mitsubishi Electric
Mitsubishi Electric CITY MULTI PKFY-P-VKM-E User manual
Popular Air Conditioner manuals by other brands
MegaLife
MegaLife NEBULA GREEN R32 Use and Installation Instructions
Panasonic
Panasonic CS-KE12NB41 installation instructions
Arbonia
Arbonia SABIANA OCEAN Series Installation and maintenance manual
TECHWOOD
TECHWOOD TRF-7008 instruction manual
Trane
Trane Packaged TerminalAir Conditioners & Heat... Installation operation & maintenance
Frigicoll
Frigicoll MKD-V300 Installation & owner's manual
