Mitsubishi Electric MELSEC iQ-F Series User manual

00100010101
00:00:00
0000000
101010001101
00100010101
101010001101
Quick Start Guide
CC-Link IE TSN Master/Local Module
FACTORY AUTOMATION
Mitsubishi Electric Programmable Controller
MELSEC iQ-F Series

1
INTRODUCTION
Thank you for purchasing the Mitsubishi Electric MELSEC iQ-F series programmable controllers.
This manual describes the handling of MELSEC iQ-F series FX5-CCLGN-MS CC-Link IE TSN master/local module.
Before using this product, please read this manual and relevant manuals carefully and develop familiarity with the
specifications to handle the product correctly.
Regarding use of this product
• This product has been manufactured as a general-purpose part for general industries, and has not been designed or
manufactured to be incorporated in a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger
movement vehicles, please contact Mitsubishi Electric sales office.
• This product has been manufactured under strict quality control. However when installing the product where major
accidents or losses could occur if the product fails, install appropriate backup or failsafe functions into the system.
Note
• If in doubt at any stage during the installation of the product, always consult a professional electrical engineer who is
qualified and trained to the local and national standards. If in doubt about the operation or use, please contact your local
Mitsubishi Electric representative.
• Mitsubishi Electric will not accept responsibility for actual use of the product based on these illustrative examples. Please
use it after confirming the function and safety of the equipment and system.
• The content, specification etc. of this manual may be changed, for improvement, without notice.
• The information in this manual has been carefully checked and is believed to be accurate; however, if you notice a doubtful
point, an error, etc., please contact your local Mitsubishi Electric representative. When doing so, please provide the manual
number given at the end of this manual.

2
CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
RELEVANT MANUALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
TERMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
GENERIC TERMS AND ABBREVIATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
KEY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
CHAPTER 1 PREPARATION 7
1.1 Applicable Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2 Operation Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sample QR code for the code reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.4 Required Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CHAPTER 2 SETTING PROGRAMMABLE CONTROLLER MASTER STATION 13
2.1 Communication Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.2 Network Configuration Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.3 Refresh Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4 Setting Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.5 Communication Settings on GX Works3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.6 Writing Programs to the Programmable Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
CHAPTER 3 SETTING PROGRAMMABLE CONTROLLER LOCAL STATION 22
3.1 Communication Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.2 Refresh Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3 Setting Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.4 Communication Settings on GX Works3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.5 Writing Programs to the Programmable Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CHAPTER 4 SETTING REMOTE STATION 25
4.1 Setting the IP Address/Station Number Setting Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.2 Setting the Function Setting Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CHAPTER 5 TCP/IP COMMUNICATION SETTING of CODE READER 27
5.1 Setting an IP Address of the Personal Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.2 Setting the Code Reader. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CHAPTER 6 OPERATION CHECK 29
6.1 Operation Check of the Local Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.2 Operation Check of the Remote Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
6.3 Operation Check of the Code Reader (TCP/IP Communications). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
CHAPTER 7 TROUBLESHOOTING 39
7.1 Checking Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.2 Checking the LED Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.3 Checking the Error Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

3
CONTENTS
APPENDICES 49
Appendix 1 CC-Link IE TSN/CC-Link IE Field Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Appendix 2 Setting an IP Address of the Personal Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
REVISIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

4
RELEVANT MANUALS
The following relevant manuals can be downloaded from the Mitsubishi Electric FA site.
https://www.mitsubishielectric.co.jp/fa/ref/ref.html?kisyu=plcf&manual=download_all
[: Available, : Not available]
Introduction for the concept and features of e-Manual Viewer is available on the following website.
http://fa-mel.com/fa/ref/ref.html?k=plceng&smerit=emaviewer_win
The installation file for Windowscan be downloaded from the following website.
http://fa-mel.com/fa/ref/ref.html?k=plceng&software=emaviewer_en
Manual name
<manual number>
Available form
e-Manual PDF
MELSEC iQ-F FX5U User's Manual (Hardware)
<JY997D55301>

MELSEC iQ-F FX5UC User's Manual (Hardware)
<JY997D61401>

MELSEC iQ-F FX5 User's Manual (CC-Link IE TSN)
<SH-082215ENG>

GX Works3 Operating Manual
<SH-081215ENG>

CC-Link IE TSN Remote I/O Module User's Manual (CC-Link IE TSN Communication Mode)
<SH-082135ENG>

Code Reader Connection Guide
BCN-P5999-1074

Code Reader CF26 User's Manual
<SH-082092ENG>

Code Reader Setting Guide
<BCN-P5999-1258>

Quick and satisfying browsing
e-Manual Viewer
e-Manual Viewer allows users to browse optimized FA-related documents
such as Mitsubishi Electric FA product manuals. e-Manual Viewer can be
downloaded for free from the Mitsubishi Electric FA Website.
All necessary documents can be easily downloaded with one
click. The latest documents are available at any time.
Example programs contained in a document can be directly copied to
an engineering tool, eliminating the need of inputting the programs.
Easy on-demand download of
latest documents
Refine search and fuzzy search are available for all downloaded
documents. Intuitive search using illustrations is available for
hardware specifications of the product.
Quick cross document search
for necessary information
Copying example programs to
an engineering tool
The documents can be customized by adding useful information
as a note freely. Latest documents and notes can be shared with
multiple users using the document sharing function.
Sharing information among multiple users

5
TERMS
Unless otherwise specified, this manual uses the following terms.
GENERIC TERMS AND ABBREVIATIONS
Unless otherwise specified, this manual uses the following generic terms and abbreviations.
Term Description
Authentication Class A group of devices and switching hubs compatible with CC-Link IE TSN, ranked according to the functions and
performance by the CC-Link Partner Association (www.cc-link.org).
Cyclic transmission A function by which data is periodically exchanged among stations on the same network using link devices
Data link Communications performed by cyclic transmission and transient transmission
Disconnection Processing for stopping the data link when a data link error occurs
Engineering tool A tool for setting, programming, debugging, and maintenance of programmable controller.
GX Works3 A generic product name for SWnDND-GXW3. ('n' indicates its version.)
Link device A device in a module on CC-Link IE TSN
Local station A station that performs cyclic transmission and transient transmission with the master station and other local stations.
The station is controlled by programs in the CPU module or other equivalent modules on the station.
Master station A station that controls the entire network. This station can perform cyclic transmission and transient transmission with all
stations. Only one master station can be used in a network.
Remote station A station that exchanges I/O signals (bit data) and I/O data (word data) with another station by cyclic transmission. This
station can perform transient transmission.
Return Processing for resuming the data link when a faulty station becomes normal
RWr A remote register of the link device. RWr refers to word data input from a slave station to the master station. (For some
areas in a local station, data are input in the opposite direction.)
RWw A remote register of the link device. RWw refers to word data output from the master station to a slave station. (For some
areas in a local station, data are output in the opposite direction.)
RX A remote input of the link device. Bit data input from a slave station to the master station. (For some areas in a local
station, data are input in the opposite direction.)
RY A remote output of the link device. Bit data output from the master station to a slave station. (For some areas in a local
station, data are output in the opposite direction.)
Slave station A station other than a master station: a local station, a remote station
SLMP An abbreviation for SeamLess Message Protocol. This protocol is used to access an SLMP-compatible device or a
programmable controller connected to an SLMP-compatible device from an external device.
TCP/IP communications One of the standard network protocols used for internet communications.
SLMP (SeamLess Message Protocol) is a communication method that uses TCP/IP.
Transient transmission A function of communications with other stations, which is used when requested by a dedicated instruction or an
engineering tool
Generic term/abbreviation Description
CC-Link IE TSN remote module A generic term for an A/D converter module, a D/A converter module, an I/O module
FX5U CPU module A generic term for FX5U-32MR/ES, FX5U-32MT/ES, FX5U-32MT/ESS, FX5U-64MR/ES, FX5U-64MT/ES, FX5U-64MT/
ESS, FX5U-80MR/ES, FX5U-80MT/ES, FX5U-80MT/ESS, FX5U-32MR/DS, FX5U-32MT/DS, FX5U-32MT/DSS, FX5U-
64MR/DS, FX5U-64MT/DS, FX5U-64MT/DSS, FX5U-80MR/DS, FX5U-80MT/DS, and FX5U-80MT/DSS
FX5UC CPU modules A generic term for FX5UC-32MT/D, FX5UC-32MT/DSS, FX5UC-64MT/D, FX5UC-64MT/DSS, FX5UC-96MT/D, FX5UC-
96MT/DSS, FX5UC-32MT/DS-TS, FX5UC-32MT/DSS-TS, and FX5UC-32MR/DS-TS
I/O module An abbreviation for the CC-Link IE TSN remote I/O module

6
KEY FEATURES
Flexible and optimum system construction with standard Ethernet devices
Since the CC-Link IE TSN and the TCP/IP network can coexist, the standard Ethernet devices can be used on the same
line. This enables to perform control communications and information communications on the same Ethernet, reducing the
design and installation cost for the system construction. Even if various data communications are performed over the
network, the system control is not affected and the punctuality of control data can be ensured.
Easy replacement of slave stations using the
automatic parameter distribution function
Easy debug of the entire network
Parameters stored in the CPU module by the master station
are automatically distributed to the slave stations when the
slave station is powered ON or disconnected stations return
to the network. This eliminates the need of writing
parameters individually to each slave station even after
replacement, facilitating replacement of the slave stations.
Parameters of all stations can be set and monitored by
connecting GX Works3 to any one of the ports in the CC-
Link IE TSN network. This eliminates the need of rewiring
cables, reducing the debug cost.
For a setting example when GX Works3 is connected to P1 connector of the
FX5-CCLGN-MS, refer to Page 29 Operation Check of the Local Station.
Programmable controller
0
50
100
InverterRemote I/OStandard
Ethernet device
Link scan time ratio [%] Time
Ò
Ò
Ó
Ô
TCP/IP communications
Transient communications
I/O control communications
Network line load Image
Information
communication
bandwidth
(ÒÓ)
Control
communication
bandwidth
(Ô)
ÔÔ Ó
Slave station
Replacement
Replacement
Slave station Slave stationSlave station
Parameters saved in the CPU module
Automatically distributing the parameters to slave stations
and changing the currently-set parameters
Automatically distributing the parameters to slave stations
and changing the currently-set parameters
Master station P1 connector of
FX5-CCLGN-MS
Remote
I/O station Local station Code
reader
Data can be transferred
by connecting to
the built-in Ethernet port
of the CPU module.
Data can be transferred
by connecting to
the built-in Ethernet port
of the CPU module.
Data can be transferred
by connecting to
the built-in Ethernet port
of the CPU module.

1 PREPARATION
1.1 Applicable Models 7
1
1PREPARATION
This manual describes the settings for cyclic transmission (communicating data periodically among stations on the network
using link devices). For other communication functions, refer to the following.
Section 4.1 Function List in the MELSEC iQ-F FX5 User's Manual (CC-Link IE TSN)
1.1 Applicable Models
The programmable controllers described in this manual are shown in the following table.
1.2 Operation Flow Diagram
Programmable controller
FX5U CPU module FX5UC CPU module
1. Preparing the required products 2. Setting the programmable
controller master station
3. Setting the programmable
controller local station
4. Setting the remote station 5. Setting TCP/IP
communications of a code
reader
6. Checking the operation
Master station Local station
Remote station
Code reader
General-purpose
switching hub
Ethernet
Master station
Ethernet
Local station
Ethernet
DataMan Setup ToolDataMan Setup Tool
Code reader
Master station
Local station
General-
purpose
switching
hub
Remote station
Code reader
TCP/IP

81 PREPARATION
1.2 Operation Flow Diagram
Sample QR code for the code reader
To read the QR code below, refer to the following for the procedure. (Page 37 Operation Check of the Code Reader (TCP/
IP Communications))
Ex.
ABCDEFG01234