Mitsubishi Electric PAR-SW96U-E User manual

１ SafetyPrecautions
２ MakingSureofComponents
５ Installationofremotecontrolholder
３ Beforeinstallation
４ Installationofwirelessreceivingunit
・Incompleteinstallationcouldcauseelectricshock,fire,etc.
・Afterusingthismanual,besuretopassittothecustomertogetherwiththeinstructionmanualprovidedwithindoorunit.Askthecustomertokeepthisinstallationmanualandthe
instructionmanualinahandyplace,andtoshowthemtotheengineerwhentheair-conditionerismovedorrepaired.Alsoaskthecustomertopassthemtoanynewuser.
・Readthese"safetyPrecautions"thoroughlyandinstallsecurely.
・Precautionsareclassifiedusingthefollowingsymbolsdependingontheextentandtypeofdangerbyerroneoushandling.
Makesurethatthefollowingcomponents,alongwiththismanual,are
packedinthebox.
●Opentheintakegrillandremovethecornerpanelwhererefrigerantpipesareandwherelocalwiresare
drawninto.
※Thecornerpanelremovedisnotneeded.
●Remove the thermistor for room temperature fixed by 1 screw and the control box cover fixed by 3
screws,whichispossibletohangtemporarily.
Remotecontrolholdercanbeusedforkeepingtheremotecontrolleronthewall.
Fittingremotecontrollerintoholder

①Fixtheremotecontrolholdertothewallusing
thetwowoodscrewsprovided.
②Inserttheremotecontrollerintotheholder.

Removingremotecontrol

●Pullouttheremotecontroller.
●Bring the cable of wireless receiving unit through the square hole
underneaththecornerpanelremovedwhererefrigerantpipesareand
wherelocalwiresaredrawninto.
●Asshowninthefigure,pullthecableintotheinsideofthecontrolbox
and connect it to CN90 on the indoor controller board. Then fix the
cablebytheclamp,beingabletoremovethereceivingunitafterwardsin
case.
●Slidethereceivingunitinthe  directionasshownandfixit bythe
screwwhichisusedforthecornerpanelremoved.
●Aftertheinstallationcompleted,setthecontrolboxandthethermistor
astheywere.
・Incompleteinstallationcouldcauseelectricshock,fire,etc.
・Otherwise,theunitcouldfall,whichcouldcauseinjury.
・Shortageinelectricalcircuitcapacityorincompleteconstructioncouldcausefire,etc.
・Modificationorincorrectrepaircouldcauseelectricshock,fire,etc.Consultthedealer
fromwhomyoupurchasedtheunit.
・Incompleteinstallationcouldcauseelectricshock,fire,etc.Askthedealeroraspecialist
forinstallation.
                
・Tensiononwirescoulddisconnectthem,orcauseheat,fire,etc.
           
・Doingsocouldcausefault,electricshock,etc.
      
・Failuretodosocouldcausefault,electricshock,etc.
      
・Failuretodosocouldcausefault,electricshock,etc.
      
・Failuretodosocouldcausefault,fire,etc.
               
           
        
・Usageinaplacewherethereismuchoil(includingmachineoil),steam,sulfidegas,
etc.couldgreatlydegradeitsperformanceordamagecomponents.
        
・Thisunitcouldmalfunctionwhenaffectedbyinverterequipment,privateelectricgenerator,high-frequencymedicalinstruments,radiocommunicationdevices,etc.Also,thisunit
couldadverselyaffectmedicalinstruments,communicationdevices,etc.,thusinterferingwithhumanmedicaltreatment,orcausingdisturbanceinbroadcastpicturesornoise.
              
・Ifgasleaksoraccumulatesaroundtheunit,itcouldcauseignition,explosion,etc.
            
・Avoidinstallinginawallwherecondensationoccurs.Installinginsuchaplacecould
causeafault,electricshock,etc.
                 
・Installinginsuchaplacecouldcausefault,electricshock,etc.
                 ! 
      
       "       
 #      
  
・Incompleteconnectionorfixingcouldcauseheat,fire,etc.
        $     
     $    
・Installinginsuchaplacecouldcausedeformation,fault,etc.
              %& ℃  
& ℃   $   
CAUTION
WARNING
CAUTION
WARNING Erroneoushandlingcancausedeathorseriousinjury.
ThismanualdescribestheinstallationforwirelessremotecontrolleroftheMitsubishipackageair-conditioner.
Readthismanualorunit'sinstallationmanualcarefully.
MitsubishiPackageAir-Conditioner
InstallationManual
Erroneoushandlingcancausepersonalinjuryordamage.
WirelessRemoteControllerKit
PAR-SW96U-E
Component
WirelessReceivingUnit（CornerPanel）
Wirelessremotecontroller
Remotecontrolholder
"AAA"LR03alkalinebatteries
4.1x16woodscrews
1
1
1
2
2
PAR−ＳW96U−E
NoteTheremotesignalwillreachthereceiveroveradistanceofapprox.7minastraight
lineandapprox.45゜leftorright.Iftheinfraredreceiverisaffectedbyfluorescentlight
(especially,invertertype),itmaynotbeabletoreceivethesignal.Takethisinto
considerationwheninstallingfluorescentlightsorreplacingthem.
WirelessReceivingUnit
（CornerPanel）
Screw
IndoorController
BoardCN90 Cable
Cramp
Squarehole
ペアNO ．
Ｊ41
Ｊ42
IndoorUnit
Grill
Refrigerantpipes
CornerPanel
Screw
Screw
Screw
Indoor
Controller
Board
JumperWire
Cont.BoxCover
IntakeGrill
IntakeSensor
※Turnoffthemainpowerbeforework.
RG79D052H01

６ ModelSelect
７ TestRun
８ PairNumberSetting
Thisremotecontrollerneedsmodelnumbersettingbeforeuse.
Setthemodelnumberinthefollowingorder.
Withoutsetting,theairconditionerwillnotworkproperly.（Thefactorysettingofmodelnumberis001.）
①PresstheSETbuttonwiththepointofaball-pointpenorthelike.
MODELSELECTblinksandmodelnumber001islighted.
Startthisoperationfromthestatusofremotecontrollerdisplayturnedoff.
② PresstheTEMP,buttonsandsetthemodelnumberaccordingtothelndoorunitmodel.（SeeTable1）

③PresstheSETbuttonwiththepointofaball-pointpenorthelike.
MODELSELECTandmodelnumberarelightedfor3seconds,thenturnedoff.
①PresstheTESTRUNbuttontwicecontinuously.
TESTRUNandcurrentoperationmodearedisplayed.
Startthisoperationfromthestatusofremotecontrollerdisplayturnedoff.
②PresstheMODEbutton.
Operationmodeswitchesbetweencoolingmodeandheatingmode.
Coolingmode…Checkoutletofcoolairflow.
Heatingmode…Checkoutletofwarmairflow.（Thisactiontakessometime.）
③PresstheFANbutton.
Checkifthefanspeedchanges.
④PresstheVANEbutton.
Checkiftheautomaticvaneisworking.
⑤PresstheON/OFFbuttonorpresstheTESTRUNbuttontwicecontinuously.
Testrunwillbecanceled.
Thisisthesettingtospecify the unit to operate with the wireless
remotecontroller.
MakesettingforJ41,J42(Jumperwire)ofindoorcontrollerboardand
thepairnumberofwirelessremotecontroller.
Thepairnumbersettingisavailablewiththe4patternsasshownin
the〈Table2〉fromAtoD.Makesettingforthepairnumber(J41,J42)
of indoor controller board and the pair number of wireless remote
controllerwhichisusedasshowninthe〈Table2〉.
※ThefactorysettingispatternA.

［Settingprocedureforpairnumberofwirelessremotecontroller］
①PresstheSETbuttonwiththepointofaball-pointpenorthelike.
MODELSELECTblinksandmodelnumberislighted.
Start this operation from the status of remote controller display
turnedoff.
②Presstheminbuttontwicecontinuously.
Pairnumber0willblink.
③PresstheTEMP,buttonsandsetthepairnumberaccordingto
thesettingpattern.（SeeTable2）
④PresstheSETbuttonwiththepointofaball-pointpenorthelike.
Pairnumberislightedfor3seconds,thenturnedoff.
〈Table1〉 Heatpump
Coolingonly 001 033
ModelNo.（H/P）/（C/O）
ON/OFF TEMP
FAN
MODE
LOUVER
VANE
CHECK
TESTRUN
AUTOSTART
MODEL
SELECT
AUTOSTOP
h
SET RESET CLOCK
min
Modelnumber
②
①③
ON/OFF TEMP
FAN
MODE
LOUVER
VANE
CHECK
TESTRUN
AUTOSTART
TEST
RUN
COOL
FAN
AUTOSTOP
h
SET RESET CLOCK
min
②
①⑤
⑤
③
④
ON/OFF TEMP
FAN
MODE
LOUVER
VANE
CHECK
TESTRUN
AUTOSTART
MODEL
SELECT
AUTOSTOP
h
SET RESET CLOCK
min
Modelnumber
PairNumber
②
①④
③
A
B
C
D
0
1
2
3〜9
Don'tcutthejumperwire.
CutthejumperwireJ41.
CutthejumperwireJ42.
Cutthejumperwireboth
J41andJ42
Setting
Pattern Pairnumberof
Wirelessremote
controller
CutpointofJumperwire
ontheindoorcontrollerboard
〈Table2〉
（1）Same setting
●All units can be operated with the same wireless remote controller.
（2）Individual setting
●
Each unit can be operated with only the wireless remote controller which the same pair number was set.
Pairnumber 1
Wirelessremotecontroller
Indoorunit receiver
section receiver section receiver section receiver section
Indoorunit
Pairnumber 2
Wirelessremotecontroller Pairnumber
3
Wirelessremotecontroller
Pairnumber 0
Wirelessremotecontroller
Indoorunit Indoorunit
Pairnumber 0 Pairnumber 1 Pairnumber 2 Pairnumber 3
●The pair number of indoor controller
board and wireless remote controller
should be set identically.
●All units should be installed in a
range that the sensor can receive the
signal from wireless remote controller.
Or an operator of wireless remote
controller should move to the proper
position to operate wireless remote
controller.
●The indoor controller board and the
wireless remote controller should be
set to pair number differently per unit.
Indoorunit
Pairnumber0 Pairnumber0
Indoorunit
Pairnumber0
Wirelessremotecontroller
Indoorunit Indoorunit receiver
section
receiver
section
receiver
section
receiver
section
Pair number 0 Pair number 0