Mitsubishi CQ-EB6260L User manual

General
Power Supply DC 12V (11V - 16V),
Test Voltage 13.2V,
Negative Ground
Current Consumption Less than 3.0A at 0.5W
Maximum Power Output 35W×4ch (at 4Ω)
Output Impedance 4Ω
AM Radio
Frequency Range 530 - 1,710kHz
Usable Sensitivity 26dB/µV (S/N 20dB)
FM Stereo Radio
Frequency Range 87.7 - 107.9MHz
Usable Sensitivity 7dB/µV (S/N 30dB)
CD Player
Signal to Noise Ratio More than 66dB
Total Harmonic Distortion Less than 0.4%
Channel Separation More than 55dB
Dimension** (W×H×D) 178 × 100 × 177.5mm
Weight** 1.5kg
* Specifications and the design are subject to possible modification
without notice due to improvements.
** Dimensions and Weight shown are approximate.
MITSUBISHI
CQ-EB6260L
AM/FM MPX ELECTRONIC TUNING
RADIO with 6-Disc CD Changer
MITSUBISHI PART No. : MR587252
ID CODE : P103
VEHICLE :ECLIPSE
DESTINATION : North America
PRODUCED AFTER :Jan., 2002
AUTOMOTIVE ELECTRONICS
Specifications*
ORDER No.5042
I0

1 FEATUERS 2
2 LASER PRODUCTS 2
3 FRONT VIEW AND FUNCTIONS 3
4 REAR VIEW AND CONNECTORS 4
5 WIRING CONNECTION 5
6 BLOCL DIAGRAM 6
7 CD DISC CENTERING ALIGNMENT 8
8 TERMINALS DESCRIPTION 9
1 FEATUERS
• • •
• PLL (Phase Locked Loop) synthesized tuning.
• • •
• 18-station preset (12-FM, 6-AM)
• • •
• FM One-tuner diversity.
• • •
• 6-Disc CD changer (in dash board)
• • •
• Electronic control of power and sound.
• • •
• Emergency ejecting function
• • •
• Anti-shock memory
• • •
• CD random, repeat function.
• • •
• MD-CH control.
9 PACKAGE AND IC BLOCK DIAGRAM 11
10 REPLACEMENT PARTS LIST 14
11 EXPLODED VIEW (Unit) 20
12 CD CHANGER PARTS LIST 21
13 EXPLODED VIEW (CD Deck) 24
14 WIRING DIAGRAM 27
15 SCHEMATIC DIAGRAM (1) 32
16 SCHEMATIC DIAGRAM (2) 33
2 LASER PRODUCTS
CONTENTS
Page Page
2
MITSUBISHI / CQ-EB6260L

3 FRONT VIEW AND FUNCTIONS
3
MITSUBISHI / CQ-EB6260L

4 REAR VIEW AND CONNECTORS
4
MITSUBISHI / CQ-EB6260L

5 WIRING CONNECTION
5
MITSUBISHI / CQ-EB6260L

6 BLOCK DIAGRAM
6.1. Main/Connector/Display Block
6
MITSUBISHI / CQ-EB6260L

6.2. CD Deck Block
7
MITSUBISHI / CQ-EB6260L

7 CD DISC CENTERING ALIGNMENT
• • •
• This adjustment is for assuring that compact discs will be placed in the center of the turntable.
<Adjustment Condition / Jig>
• • •
• Power Supply Voltage : 13.2V
• • •
• Test Disc : TCD-792A
<Adjustment Procedures>
1.Attach the adjusting screw to the upper chassis (See Figure 1.).
2.Insert the test CD (TCD-792A) into the disc No.1 position and play it.
3.After checking whether the disc is centered on the turntable, turn the adjusting screw unit it is in the center.
<Check Items>
• • •
• Check that the disc is correctly centered.
• • •
• Check that the disc is securely clamped.
• • •
• Check that no abnormal noise is produced when clamping the disc.
[Directions of Turning the Adjusting Screw]
• • •
• CD stops before its proper position : Turn the screw counterclockwise.
• • •
• CD overruns : Turn the screw clockwise.
4. After the adjustment, lock the screw.
8
MITSUBISHI / CQ-EB6260L

8.1. Main Block
IC601 : C2BBGF000290
Pin
No. Port Descriptions I/O Vol. (V)
1 KR2 Key Data I 0
2 KR1 Key Data I 5.1
3 KR0 Key Data I 0
4 AVSS Ground - 0
5 KS0 Key strobe O 0
6 KS1 Key strobe O 0
7AVREF +5V power supply - 5.1
8 KS2 Key strobe O 0
9 KS3 Key strobe O 0
10 LOAD LED LED Load O 0
11 CD DI CD data output O 2.4
12 CD DO CD data input I 1.4
13 CD CLK Shift clock for CD data O 4.9
14 PLL DI PLL data input I 5.0
15 MBUSY OUT M-BUS busy O 0
16 MBUSY IN M-BUS busy I 0
17 MDATA M-BUS data I/O 4.9
18 MCLK M-BUS clock O 4.9
19 PLLDO PLL data output O 0
20 PLLSTB PLL strobe O 0
21 PLLCLK PLL clock O 0
22 MUTE A Mute signal O 0
23 VOL STB Electric volume strobe O 0
24 VOL CLK Electric volume clock O 0
25 VOL DATA Electric volume data O 0
26 AMP CONT Power amp. stand-by O 4.9
27 P.ON Power switch O 4.9
28 START/STOP CD Deck start stop O 4.9
29 P.5V ON P.5V Power switch O 0
30 DIV SW Diversity switch I 4.8
31 TUNE 2 Tuner switch signal I 4.7
32 TUNE 1 Tuner switch signal I 0.5
33 GND Ground - 0
34 VOL 2 Volume switch signal I 0
35 VOL@1 Volume switch signal I 0
36 CD RESET CD controller reset O 0
37 MAIN Main antenna selection O 4.9
38 SUB Sub. antenna selection O 8.3
39 - - - -
40 SECDI Security data input I 0
41 - - - -
42 - - - -
43 - - - -
44 FreqOUT Tone/Burst frequency O 0
45 TONE/TRG Tone/Triger control O 0
46 BUZZER Buzzer output O 0
47 Ga INPUT GALA signal input I 5.0
48 ST FM stereo detection I 0.3
49 LED-ENABLE LED enable O 4.8
50 LED-LATCH LED latch O 0
51 LED-CLOCK LED clock O 0
52 LED-DATA LED data O 0
53 SET S0 System function setting O 0
54 - - - -
55 SET R0 System function setting I 0
56 SET R1 System function setting I 0
57 TEL MUTE Telephone mute I 1.6
58 REMOTE-D - - 0
59 P.CONT System power control O 0
60 RESET Reset input I 4.8
61 M-DATA IN M-BUS data I 4.9
62 EJECT SW CD eject SW I 4.8
63 BATDROP Battery level Drop I 5.0
64 ACCDROP ACC level Drop I 0
65 - - - -
66 ANT Motor antenna power on/off O 0
67 VSS Ground - 0
Pin
No. Port Descriptions I/O Vol. (V)
68 VDD +5V power supply - 4.9
69 X2 Crystal oscillator - 0
70 X1 Crystal oscillator - 2.6
71 GND Ground - 0
72 XT2 Crystal oscillator - 2.7
73 XT1 Crystal oscillator - 2.5
74 AVDD +5V power supply - 4.9
75 AV REF0 +5V power supply - 5.0
76 VAM/FM AM/FM vcont I 0
77 REMOTE_A Remote control O 5.0
78 BIBIRI.A (Ground pull-down) - 0
79 SENCE-CAR - O 5.0
80 KR3 Key Data I 0
Note 1 : Voltage measuerments are with respect to ground,
with a voltmeter (internal resistance : 10M ohms).
8.2. CD Deck Block
IC201 : MN662783RPW
Pin
No. Port Description I/O (V)
1 VDD +5V power supply - 5.0
2 D0 D-RAM data I/O 2.3
3 D1 D-RAM data I/O 1.8
4/WE D-RAM data write O 4.9
5 /RAS D-RAM row address strobe O 3.4
6 D2 D-RAM data I/O 0.8
7 D3 D-RAM data I/O 0
8 /CAS0 D-RAM columun address strobe O 3.9
9 /CAS1 D-RAM columun address strobe O 0
10 A8 D-RAM address O 0.6
11 A7 D-RAM address O 1.1
12 A6 D-RAM address O 0.7
13 A5 D-RAM address O 0
14 A4 D-RAM address O 1.1
15 A9 D-RAM address O 0.4
16 A0 D-RAM address O 1.0
17 A1 D-RAM address O 1.0
18 A2 D-RAM address O 1.0
19 A3 D-RAM address O 0
20 VSS2 Ground - 0
21 VDD2 +5V power supply - 5.0
22,23 - Not used - -
24 TVD Traverse motor control O 2.5
25 PC Not used - -
26 ECS Spindle motor control O 2.4
27 TRD Tracking coil drive O 2.5
28 FOD Focus coil drive O 2.4
29 FBAL Focus balance O 1.9
30 TBAL Tracking balance O 3.0
31 VREF Reference voltage I 2.5
32 FE Focus error I 2.5
33 TE Tracking error I 2.5
34 RFENV RF envelope I 2.5
35 OFT Off track signal I 0
36 /RFDET RF detecting signal I 0
37 BDO Drop-out signal I 0
38 LDON Laser on signal O 4.5
39 ARF RF signal I 2.5
40 IREF Reference current input I 1.2
41 DRF Biase for DSL I 2.4
42 DSLF Loop filter for DSL I/O 2.5
43 SDLF2 Loop filter for DSL I/O 2.2
44 PLLF Loop filter for PLL I/O 1.4
8 TERMINALS DESCRIPTION
9
MITSUBISHI / CQ-EB6260L

45 VCOF Not used - -
46 AVDD2 +5V power supply - 5.0
47 AVSS2 Ground - 0
48 OUTL L channel output O 2.3
49 AVSS1 Ground - 0
50 OUTR R channel output O 2.3
51 AVDD1 +5V power supply - 4.7
52-54 - (Connecting to ground) - 0
55 FLAG Flag output O 0
56 FCLK Frame clock O 0
57-59 - Not used - -
60 TX Not used - -
61 MCLK Clock for I/F command I 1.0
62 MDATA Data for I/F command I 3.1
63 MLD I/F command load I 5.0
64 BLKCK Subcode block clock O 0
65 SQCK Ext. clock for sub code-Q I 5.0
66 SUBQ Code for sub. code-Q O 3.8
67 DMUTE Mute input I 0
68 STAT Status signal O 5.0
69 /RST Reset input I 5.0
70 CSEL (Connecting to ground) - 0
71 PMCK PM clock O 2.5
72 SMCK SM clock O 2.5
73 SUBC Serial data of sub code O 0
74 SBCK Shift clock for SUBC I 0.6
75 /CLDCK Not used - -
76 /TEST (Connecting to VDD) - 5.0
77 X1 Crystal oscillator - 0.4
78 X2 Crystal oscillator - 3.2
79 VDD1 +5V power supply - 5.0
80 VSS1 Ground - 0
IC301 : MNS73260ACBL
Pin
No. Port Description I/O (V)
1 VDD +5V power supply - 5.0
2 OSC2 Crystal oscillator - 2.2
3 OSC1 Crystal oscillator - 2.1
4 VSS Ground - 0
5XI (Connecting to ground) - 0
6XO Not used - -
7 CM (Connecting to ground) - 0
8 VREFH Reference voltage I 5.0
9SW13 Shuter SW I 4.9
10 SW12 Horizontal origin I 4.9
11 SW11 Clump SW I 0
12 SW10 Play SW I 0
13 SW4 Shuter SW I 4.9
14 SW3 Tray origin SW I 0
15 SW2 Inner SW I 4.8
16 SW1 Outer SW I 4.9
17 VREFL Reference voltage I 0
18 /RESET Reset input I 4.9
19 - (Ground pull-down) - 0
20 SCKM Clock for serial data I 5.0
21 SIM CD changer serial data I 1.3
22 SOM CD changer serial data O 4.3
23 SQCK Ext. clock for sub. code-Q O 5.0
24 SUBQ Code for sub. code-Q I 1.6
25 - Not used - 5.0
26 - (Ground pull-down) - 0
27 CD.ON CD changer start/stop I 5.0
28 - Not used - 5.0
29 BLKCK Sub. code block clock I 0
30 P.ON Not used - 5.0
31 MUTE Mute output O 5.0
32 - (Ground pull-down) - 0
33 SENS Servo status O 0
34 CLVS Servo status O 5.0
35 FLOCK Focus servo lock O 0.2
36 TLOCK Tracking servo lock O 0
37 VMI Horizontal motor control O 2.5
38 HMI Vertical motor control O 0
39 HVMUTE H/V motor mute O 0
40-42 - (Ground pull-down) - 0
43 SW9 Disc-in (B) SW I 0
44 SW8 Disc-in (L) SW I 0
45 SW7 Disc-in (F) SW I 0
46 SW6 Disc push SW I 0
47 SW5 Tray hight SW I 4.5
48 BDO Drop-out signal I 0
49 DQSY Not used - -
50 /RST Reset output O 5.0
51 STAT Status signal I 2.1
52 DMUTE Mute output O 0
53 XE Not used - -
54 P.DOWN Power down signal O 0
55 - No connection - -
56 MLD I/F command load O 5.0
57 MDATA Data for I/F command O 3.1
58 MCLK Clock for I/F command O 4.1
59 SPMT Spindle mute O 5.0
60 MUTE12 Focus/Tracking mute O 0
61 MUTE4 Loading motor mute O 4.8
62 LDOI Loading motor control I/O 2.5
63 TRV Forced traverse control I/O 2.4
64 SYNC Not used - -
10
MITSUBISHI / CQ-EB6260L