Mitsubishi FX2NC DSS Series User manual

DSS/DS
HARDWARE MANUAL
FX2NC (DSS/DS) SERIES PROGRAMMABLE CONTROLLERS
Санкт-Петербург, ул. Седова, д.53
[phone]
[email protected] www.elinc.ru

FX2NC Series Programmable Controllers
Foreword
• This manual contains text, diagrams and explanations which will guide the reader in the correct installation and
operation of the FX2NC. It should be read and understood before attempting to install or use the unit.
• Further information can be found in the FX2NC Series Hardware Manual and FX Series Programming Manual II.
• If in doubt at any stage of the installation of FX2NC always consult a professional electrical engineer who is
qualified and trained to the local and national standards that applies to the installation site.
• If in doubt about the operation or use of FX2NC please consult the nearest Mitsubishi Electric distributor.
• This manual is subject to change without notice.

i
FX2NC (DSS/DS) Series Programmable
Controllers
Hardware Manual
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent
licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial
property rights which may occur as a result of using the contents noted in this manual.
FX2NC Series Programmable Controllers
Manual number :JY992D76401
Manual revision :G
Date :November 2005

FX2NC Series Programmable Controllers
ii
Guidelines for the safety of the user and protection of the FX2NC.
This manual provides information for the installation and use of the FX2NC. The manual has
been written to be used by trained and competent personnel. The definition of such a person
or persons is as follows:
a) Any engineer who is responsible for the planning, design and construction of automatic
equipment using the product associated with this manual, should be of a competent
nature, trained and qualified to the local and national standards required to fulfill that
role. These engineers should be fully aware of all aspects of safety with regards to
automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and
qualified to the local and national standards required to fulfill that job. These engineers
should also be trained in the use and maintenance of the completed product. This
includes being completely familiar with all associated documentation for said product. All
maintenance should be carried out in accordance with established safety practices.
c) All operators of the completed equipment (see Note) should be trained to use this
product in a safe manner in compliance to established safety practices. The operators
should also be familiar with documentation which is associated with the actual operation
of the completed equipment.
Note : The term ‘completed equipment’ refers to a third party constructed device which
contains or uses the product associated with this manual.

FX2NC Series Programmable Controllers
iii
Notes on the Symbols Used in this Manual
At various times throughout this manual certain symbols will be used to highlight points which
are intended to ensure the users personal safety and protect the integrity of equipment.
Whenever any of the following symbols are encountered its associated note must be read and
understood. Each of the symbols used will now be listed with a brief description of its meaning.
Hardware warnings
Software warning
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property damage
.
3) Indicates a point of further interest or further explanation.
4) Indicates special care must be taken when using this element of software.
5) Indicates a special point which the user of the associate software element should be awar
e
of.
6) Indicates a point of interest or further explanation.

FX2NC Series Programmable Controllers
iv
• Under no circumstances will Mitsubishi Electric be liable responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to
understanding the text, not to guarantee operation. Mitsubishi Electric will accept no
responsibility for actual use of the product based on these illustrative examples.
• Please contact a Mitsubishi Electric distributor for more information concerning applications
in life critical situations or high reliability.

FX2NC Series Programmable Controllers
v
Note Concerning the CE Marking
This note does not guarantee that an entire mechanical module produced in accordance with
the contents of this note will comply with the following standards. Compliance to EMC directive
and LVD directive of the entire mechanical module should be checked by the user /
manufacturer.
For more details please contact the local Mitsubishi Electric sales site.

FX2NC Series Programmable Controllers
vi
EMC
The following products have shown compliance through direct testing (of the identified
standards below) and design analysis (through the creation of a technical construction file) to
the European Directive for Electromagnetic Compatibility (89/336/EEC) when used as directed
by the appropriate documentation.Refer to a manual or related material of each product for
details concerning products not included below.
Type : Programmable Controller (Open Type Equipment)
Models : MELSEC FX2NC series manufactured
from March 1st, 1999 FX2NC-MT-DSS Where  indicates:16,32,64,96
FX2NC-ËËEX-DS FX2NC-ËËEYT-DSS
Where ËË indicates:16,32
FX2NC-EEPROM-16 FX2NC-RTC
FX2NC-EEPROM-4C FX2NC-EEPROM16C
from August 1st, 1999 FX2NC-16MR-T-DS
FX2NC-16EX-T-DS FX2NC-16EYR-T-DS
from July 1st, 2001 FX2NC-ROM-CE1
from October 1st, 2002 FX2NC-232ADP FX2NC-485ADP

FX2NC Series Programmable Controllers
vii
Models : MELSEC FX0N series manufactured
from November 1st, 1995 FX0N-8EX-ES, FX0N-8EYR-ES, FX0N-8EYT-ESS
from February 1st, 1996 FX0N-8ER-ES, FX0N-16EX-ES, FX0N-16EYR-ES,
FX0N-16EYT-ESS
from April 1st, 1996 FX0N-8ER-ES/UL, FX0N-16EX-ES/UL, FX0N-16EYR-ES/UL,
FX0N-16EYT-ESS/UL
from May 1st, 1996 FX0N-232ADP FX0N-485ADP
from July 1st, 1996 Harmonized Products
FX0N-8EX-ES/UL, FX0N-8EYR-ES/UL, FX0N-8EYT-ESS/UL
Standard Remark
EN50081-2:1993 Electromagnetic compatibility
EN61000-6-4:2001 - Generic emission standard
Industrial environment
Compliance with all relevant aspects of the
standard.
(Radiated Emissions and Mains Terminal Voltage
Emissions)
EN61000-6-2:2001 Electromagnetic compatibility
- Generic immunity standard
Industrial environment
Compliance with all relevant aspects of the
standard.
(RF immunity,Fast Transients,ESD,Conducted,
Surge, Power magnetic fields,Voltage dips and
Voltage interruptions)

FX2NC Series Programmable Controllers
viii
Models : MELSEC FX2N series manufactured
from July 1st, 1997 FX2N-16EX-ES/UL FX2N-16EYR-ES/UL FX2N-16EYT-ESS/UL
from August 1st, 2005 FX2N-8ER-ES/UL FX2N-8EX-ES/UL
FX2N-8EYR-ES/UL FX2N-8EYT-ESS/UL
to March 31st,2002 [compliance with EN50081-2 (EN61000-6-4) and EN50082-2]
from April 1st 2002:Above mentioned products [compliance with EN50081-2
(EN61000-6-4) and EN61131-2]
Standard Remark
EN50081-2:1993Electromagnetic compatibility
EN61000-6-4 -Generic emission standard
:2001 Industrial environment
Compliance with all relevant aspects of the standard.
(Radiated Emissions and Mains Terminal Voltage
Emissions)
EN50082-2:1995 Electromagnetic compatibility
- Generic immunity standard
Industrial environment
Compliance with all relevant aspects of the standard.
(RF immunity,Fast Transients,ESD,Conducted, and
Power magnetic fields)
EN61131-2:1994 Programmable controllers
/A11:1996 - Equipment requirements
/A12:2000 and tests
Compliance with all relevant aspects of the standard.
(RF Immunity, Fast Transients , ESD and Damped
oscillatory wave)