Mitsubishi A950GOT User manual

Get other manuals https://www.bkmanuals.com

Get other manuals https://www.bkmanuals.com

A - 1
SAFETY PRECAUTIONS
(Always read these instructions before using this equipment.)
Before using this product, please read this manual and the relevant manuals introduced in this manual
carefully and pay full attention to safety to handle the product correctly.
The instructions given in this manual are concerned with this product. For the safety instructions of the
programmable controller system, please read the CPU module user's manual.
In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".
Note that the CAUTION level may lead to a serious consequence according to the circumstances.
Always follow the instructions of both levels because they are important to personal safety.
Please save this manual to make it accessible when required and always forward it to the end user.
[Design Precautions]
DANGER
Depending on the GOT main unit, communication board, communication module or cable fault, the
output from the GOT interface module may remain ON or may remain OFF.
An external monitoring circuit should be provided to check for output signals which may lead to a
serious accident.
Not doing so can cause an accident due to false output or malfunction.
If a communication fault (including cable disconnection) occurs during monitoring on the GOT,
communication between the GOT and PLC CPU is suspended and the GOT becomes inoperative.
For bus connection : The CPU becomes faulty and the GOT inoperative.
For other than bus connection : The GOT becomes inoperative.
A system where the GOT is used should be configured to perform any significant operation to the
system by using the switches of a device other than the GOT on the assumption that a GOT
communication fault will occur.
Not doing so can cause an accident due to false output or malfunction.
Do not use the GOT as the warning device that may cause a serious accident.
An independent and redundant hardware or mechanical interlock is required to configure the device
that displays and outputs serious warning.
Failure to observe this instruction may result in an accident due to incorrect output or malfunction.
DANGER Indicates that incorrect handling may cause hazardous conditions,
resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous conditions,
resulting in medium or slight personal injury or physical damage.
CAUTION
Get other manuals https://www.bkmanuals.com

A - 2
[Design Precautions]
[Mounting Precautions]
DANGER
Incorrect operation of the touch switch(s) may lead to a serious accident if the GOT backlight is
gone out.
When the GOT backlight goes out, the display section turns black and causes the monitor screen
to appear blank, while the input of the touch switch(s) still remains active.
This may confuse an operator in thinking that the GOT is in “screensaver” mode, who then tries to
release the GOT from this mode by touching the display section, which may cause a touch switch
to operate.
Note that the following occurs on the GOT when the backlight goes out.
The monitor screen disappears even when the screensaver is not set.
The monitor screen will not come back on by touching the display section, even if the
screensaver is set.
CAUTION
Do not bundle the control and communication cables with main-circuit, power or other wiring.
Run the above cables separately from such wiring and keep them a minimum of 100mm apart.
Not doing so noise can cause a malfunction.
DANGER
Before installing or removing the GOT main unit to or from an enclosure, always turn the GOT
power OFF before installing or removing the GOT main unit to or from an enclosure.
Not doing so can cause a module failure or malfunction.
Before loading or unloading the communication board, communication module, external I/O
interface module or memory card interface module to or from the GOT, always turn the GOT
power OFF before loading or unloading the communication board, communication module,
external I/O interface module or memory card interface module to or from the GOT.
Not doing so can cause a module failure or malfunction.
CAUTION
The GOT should be used in the environment given in the general specifications of this user's
manual.
Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration.
When mounting the GOT main unit to an enclosure, tighten the mounting screws in the specified
torque range.
Undertightening can cause a drop, short circuit or malfunction.
Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or
module.
Get other manuals https://www.bkmanuals.com

A - 3
[Mounting Precautions]
[Wiring Precautions]
CAUTION
When loading the communication board, External I/O interface module or communication module
to the GOT main unit, fit it to the connection interface of the GOT and tighten the mounting screws
in the specified torque range.
Undertightening can cause a drop, failure or malfunction.
Overtightening can cause a drop, failure or malfunction due to the damage of the screws or
module.
When loading the communication board to the GOT main unit, take care not to become injured by
the components that are installed or surrounding materials.
When loading the communication board to the GOT main unit, remove any static electricity
accumulated on your body before engaging in work.
Otherwise, this may result in damage to the board.
DANGER
Before starting wiring, always turn the GOT power OFF before starting wiring.
Not doing so may cause an electric shock, product damage or malfunction.
CAUTION
Please make sure to ground FG terminal of the GOT power supply unit by applying Class D
Grounding (Class 3 Grounding Method) or higher which is used exclusively for the GOT.
Not doing so may cause an electric shock or malfunction.
Correctly wire the power supply module on the GOT after confirming the rated voltage and
terminal arrangement of the product.
Not doing so can cause a fire or failure.
Tighten the terminal screws of the GOT power supply section in the specified torque range.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or
module.
Exercise care to avoid foreign matter such as chips and wire offcuts entering the module.
Not doing so can cause a fire, failure or malfunction.
Plug the bus connection cable by inserting it into the connector of the connected module until it
"clicks".
After plugging, check that it has been inserted snugly.
Not doing so can cause a malfunction due to a contact fault.
Plug the communication cable into the connector of the connected module and tighten the
mounting and terminal screws in the specified torque range.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or
module.
Get other manuals https://www.bkmanuals.com

A - 4
[Test Operation Precautions]
[Startup/Maintenance Precautions]
DANGER
Before performing test operation (bit device on/off, word device's present value changing, timer/
counter's set value and present value changing, buffer memory's present value changing) for a
user-created monitor screen or system monitoring, read the manual carefully to fully understand
how to operate the equipment.
During test operation, never change the data of the devices which are used to perform significant
operation for the system.
False output or malfunction can cause an accident.
DANGER
When opening the panel on which the GOT is installed, always power off the GOT.
Not doing so can cause the GOT to fail or malfunction.
When power is on, do not touch the terminals.
Doing so can cause an electric shock or malfunction.
Do not change the extension number setting switch and I/O slot setting switch setting during
power-on.
Doing so can cause a malfunction.
Before starting cleaning or terminal screw retightening, always turn the power OFF before starting
cleaning or terminal screw retightening.
Not switching the power off in all phases can cause a module failure or malfunction.
Undertightening can cause a short circuit or malfunction.
Overtightening can cause a short circuit or malfunction due to the damage of the screws or
module.
When touching the GOT, communication unit, and/or option unit, or before touching the panel with
the GOT installed, touch a grounded metal object to discharge the static electricity from the
human body.
Failure to do so may cause the unit to fail or malfunction.
CAUTION
Do not disassemble or modify the module.
Doing so can cause a failure, malfunction, injury or fire.
Do not touch the conductive and electronic parts of the module directly.
Doing so can cause a module malfunction or failure.
The cables connected to the module must be run in ducts or clamped.
Not doing so can cause the module or cable to be damaged due to the dangling, motion or
accidental pulling of the cables or can cause a malfunction due to a cable connection fault.
When unplugging the cable connected to the module, do not hold and pull the cable portion.
Doing so can cause the module or cable to be damaged or can cause a malfunction due to a
cable connection fault.
Get other manuals https://www.bkmanuals.com

A - 5
[Backlight Changing Precautions]
[Disposal Precautions]
DANGER
Before changing the backlight, always turn the GOT power OFF (when using a GOT bus
connection, also turn OFF the PLC CPU power), and remove the GOT main unit from the panel
before changing the backlight.
Not switching the power off in all phases may cause an electric shock.
Not removing the unit from the enclosure can cause injury due to a drop.
CAUTION
When replacing the backlight, use the gloves.
Otherwise, it may cause you to be injured.
If you should directly touch the plated area of the main unit case with hand, be sure to wipe off the
fingerprint and so on, and install the main unit case.
Otherwise, it may cause a trouble or malfunction.
Start changing the backlight more than 5 minutes after switching the GOT power off.
Not doing so can cause a burn due to the heat of the backlight.
CAUTION
When disposing of the product, handle it as industrial waste.
Get other manuals https://www.bkmanuals.com

A - 6
REVISIONS
The manual number is given on the bottom left of the back cover..
Print Date * Manual Number Revision
Jul., 1999 SH (NA)-080018-A First edition
Mar., 2000 SH (NA)-080018-B
Section 1.1, Chapter 5, Section 6.2, Section 6.3, Section 6.5, Section 6.6, Section
6.7, Section 6.8
Section 2.1, Section 2.3, Section 3.1, Section 3.2, Section 3.3, Chapter 4, Section
6.1, Section 6.4, Section 7.4, Appendix 1, Appendix 2, Appendix 3, Index
Section 2.2, Section 2.4, Section 6.9, Section 8.4
Descriptions of A951GOT-QTBD/QSBD/QLBD(-M3) are added.
Descriptions of A950/951/953/956GOT-TBD(-M3) are added.
Feb., 2001 SH (NA)-080018-C
Section 1.1, Section 2.1, Section 2.2, Section 2.3, Section 2.4,
Section 3.1, Section 3.3, Section 4.1, Section 6.1, Section 6.2,
Section 6.4, Section 6.7, Section 6.8, Section 6.9, Section 6.10,
Section 6.11, Section 6.12, Section 7.4, Section 8.2, Section 8.3,
Appendix 1, Appendix 2
Section 6.3, Section 6.5, Section 6.6
Additional model
Descriptions of A956WGOT-TBD is added.
May, 2001 SH (NA)-080018-D
Section 6.3.1
Section 1.1, Section 2.2, Section 2.3, Section 3.2, Section 6.7.1,
Section 6.12.2, Section 9.2, Appendix 2
Chapter 8
Feb., 2002 SH (NA)-080018-E
SAFETY PRECAUTIONS
Apr., 2002 SH (NA)-080018-F
Section 8.2.2, Section 8.2.3, Section 8.2.5
Chapter 4, Section 8.2.1, Section 8.3.1, Section 8.3.2, Section 8.3.3,
Section 9.2
Section 8.2.4
Partial correction
Partial addition
Addition
Addition model
Partial correction
Addition
Partial correction
Partial addition
Addition
Partial correction
Partial correction
Partial addition
Addition
Get other manuals https://www.bkmanuals.com

A - 7
Japanese Manual Version SH-080011-H
1999 MITSUBISHI ELECTRIC CORPORATION
Sep., 2004 SH (NA)-080018-G
Changed from 13JL92 to 1DM103.
Chapter 1, Section 2.1, Section 2.2.2, Section 2.3, Section 2.4,
Section 2.5, Section 3.1, Section 3.2, Chapter 4, Chapter 5,
Section 6.1.3, Section 6.3.1, Section 6.4.2, Section 6.4.3, Section 6.4.4, Section
6.5, Section 6.8.2, Section 6.9.2, Section 6.10.1, Section 6.10.2, Section 6.12.2,
Section 7.4, Section 8.1.1, Section 8.2.2, Section 8.2.4, Section 8.3.2, Section
8.3.3, Section 9.3, Appendix 1, WARRANTY
Section 3.2, Section 6.7.1, Section 6.7.2, Appendix 2
Section 6.2, Section 6.2.1, Section 6.2.2, Section 6.2.3, Section 6.2.4, Section 6.13
A95 GOT-SBD(-M3)-B, A95 GOT-QSBD(-M3)-B
Dec., 2005 SH (NA)-080018-H
Section 3.2, Section 9.3, Appendix 3
Section 9.2
Oct., 2006 SH (NA)-080018-I
SAFETY PRECAUTIONS, Section 2.3, Section 3.2, Section 3.3,
Section 8.1.1, Section 8.3.2
Section 8.2.5, Section 8.3.1, Section 8.3.2, Section 8.3.3
Nov., 2006 SH (NA)-080018-J
Layouts were revised.
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.
Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Print Date * Manual Number Revision
MODEL CODE change
Partial correction
Partial addition
Addition
Addition model
Partial correction
Partial addition
Partial correction
Partial addition
Partial correction
Get other manuals https://www.bkmanuals.com

A - 8
SAFETY PRECAUTIONS .................................................................................................................................A - 1
1. ABOUT THE MANUALS .............................................................................................................................A - 11
2. ABBREVIATIONS AND GENERIC TERMS IN THIS MANUAL..................................................................A - 12
3. PACKING LIST ...........................................................................................................................................A - 14
1 OVERVIEW 1 - 1 to 1 - 4
1.1 Features 1 - 3
2 SYSTEM CONFIGURATION 2 - 1 to 2 - 12
2.1 Overall Configuration 2 - 1
2.2 System Configuration of the GOT 2 - 3
2.3 Component List 2 - 3
2.4 Software Packages to be Used 2 - 9
2.5 Unusable Conventional Products 2 - 10
2.6 Notes on Q4ARCPU Duplex System 2 - 11
3 PERFORMANCE 3 - 1 to 3 - 8
3.1 General Specifications 3 - 1
3.2 Performance Specifications 3 - 2
3.3 Power Supply Specifications 3 - 8
4 NAMES OF THE PARTS AND THEIR SETTINGS 4 - 1 to 4 - 2
5 ROUGH PRE-OPERATION PROCEDURE 5 - 1 to 5 - 2
6 HANDLING 6 - 1 to 6 - 29
6.1 GOT Main Unit 6 - 1
6.1.1 Handling instructions ............................................................................................................ 6 - 1
6.1.2 Installation method................................................................................................................ 6 - 3
6.1.3 Wiring method....................................................................................................................... 6 - 5
6.1.4 Installation of handy type GOT ........................................................................................... 6 - 11
6.2 Protective Sheet 6 - 13
6.2.1 Protective sheet type .......................................................................................................... 6 - 13
6.2.2 Mounting procedure............................................................................................................ 6 - 13
6.3 Memory board (A956WGOT only) 6 - 14
6.3.1 Memory board types ........................................................................................................... 6 - 14
6.3.2 Mounting procedure............................................................................................................ 6 - 14
INTRODUCTION
Thank you for choosing the Mitsubishi Graphic Operation Terminal.
Before using the equipment, please read this manual carefully to use the equipment to its optimum.
A copy of this manual should be forwarded to the end user.
CONTENTS
Get other manuals https://www.bkmanuals.com