Mitsubishi F940 User manual

HARDWARE MANUAL
F940GOT-SWD-E/LWD-E

F940GOT-SWD-E/LWD-E
Foreword
• This manual contains text, diagrams and explanations which will guide the reader in the
correct installation and operation of the communication facilities of FX series.
• Before attempting to install or use the communication facilities of FX series this manual
should be read and understood.
• If in doubt at any stage of the installation of the communication facilities of FX series
always consult a professional electrical engineer who is qualified and trained to the local
and national standards which apply to the installation site.

F940GOT-SWD-E/LWD-E
i
F940GOT-SWD-E/LWD-E
HARDWARE MANUAL Manual number : JY992D77901
Manual revision : D
Date : February 2000

F940GOT-SWD-E/LWD-E
ii
Guidelines for the safety of the user and protection of the F940GOT-SWD-E/LWD-E
This manual provides information for the installation and use of the Graphic Operation Terminal F940GOT.
The manual has been written to be used by trained and competent personnel. The definition of such a person
or persons is as follows;
a ) Any engineer who is responsible for the planning, design and construction of automatic equipment
using the product associated with this manual should be of a competent nature, (trained and qualified
to the local and national standards required to fulfill that role). These engineers should be fully aware
of safety with regards to automated equipment.
b ) Any commissioning or service engineer must be of a competent nature, trained and qualified to the
local and national standards required to fulfill that job. These engineers should also be trained in the
use and maintenance of the completed product. This includes being completely familiar with all asso-
ciated documentation for the said product. All maintenance should be carried out in accordance with
established safety practices.
c ) All operators of the compliance product should be trained to use that product in a safe and coordi-
nated manner in compliance to established safety practices. The operators should also be familiar
with all documentation which is connected with the actual operation of the completed equipment.
Note:The term ‘completed equipment’ refers to a third party constructed device which contains or uses the
product associated with this manual.

F940GOT-SWD-E/LWD-E
iii
Note’s on the symbology used in this manual
At various times through out this manual certain symbols will be used to highlight points of information which
are intended to ensure the users personal safety and protect the integrity of the equipment. Whenever any of
the following symbols are encountered, its associated note must be read and understood. Each of the sym-
bols used will now be listed with a brief description of its meaning.
Hardware warnings
Software warnings
1 ) Indicates that the identified danger WILL cause physical and property damage.
2 ) Indicates that the identified danger POSSIBLY cause physical and property damage.
3 ) Indicates a point of further interest or further explanation.
1 ) Indicates special care must be taken when using this element of software.
2 ) Indicates a special point of which the user of the associate software element should be aware.
3 ) Indicates a point of interest or further explanation.

F940GOT-SWD-E/LWD-E
iv
Memo

F940GOT-SWD-E/LWD-E
v
CONTENTS
1. INTRODUCTION...................................................................................1-1
1.1 Outline of product................................................................................................1-2
1.2 Product configuration...........................................................................................1-8
1.3 System configuration.........................................................................................1-14
2. Installation, Wiring and General Specifications.....................................2-1
2.1 Installation of main body......................................................................................2-1
2.2 Wiring of power supply........................................................................................2-4
2.3 Functions of operation keys and connectors.......................................................2-9
2.4 Outside dimensions...........................................................................................2-12
2.5 General specificationsl ......................................................................................2-13
2.6 Connection to personal computer......................................................................2-15
2.7 CPU port connection .........................................................................................2-18
2.8 Computer link port connection (MELSEC A Series)..........................................2-26
2.9 Connection to SYSMAC C Series .....................................................................2-29
2.10 Connection to FLEX-PC N Series .....................................................................2-32
2.11 Connection by general-purpose communication ...............................................2-35
3. Startup...................................................................................................3-1
3.1 Startup procedure................................................................................................3-2
3.2 Operation environment setting ............................................................................3-5
4. Extension Module..................................................................................4-1
4.1 Data transfer adaptor...........................................................................................4-1

F940GOT-SWD-E/LWD-E
vi
5. Maintenance..........................................................................................5-1
5.1 Outline of maintenance........................................................................................5-1
5.2 Replacement of battery .......................................................................................5-3
5.3 Replacement of backlight....................................................................................5-5
6. Troubleshooting.....................................................................................6-1
6.1 Power indication ..................................................................................................6-1
7. Additional Functions (in Ver3.00 or later)..............................................7-1
7.1 Applicable Versions and Models .........................................................................7-1
7.2 Connection to MELSEC QnA Series PC.............................................................7-2
7.3 Connection to SLC 500 Series............................................................................7-3
7.4 Connection to Bar Code Reader .........................................................................7-5
7.5 Screen Hard Copy Function ................................................................................7-7
7.6 Additional Function in Alarm History Display.......................................................7-8
7.7 Specification of Ten-Key Window Initial Display Position....................................7-8
8. Additional Functions (in V3.10 or later) .................................................8-1
8.1 Applicable Versions and Models .........................................................................8-1
9. Additional Functions (in V4.00 or later) .................................................9-1
9.1 Applicable Versions and Models .........................................................................9-1
Note to User
This manual describes installation, wiring and the specifications of the F940GOT.
For handling and operating procedures of the F940GOT main body, refer to the
F940GOT Operation Manual offered separately.

INTRODUCTION 1.
1-1
1. INTRODUCTION
This section describes the product configuration and the system configuration of the graphic
operation terminal.
Confirm various functions of each unit.
F940GOT-SWD-E/LWD-E

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-2
1.1 Outline of product
The graphic operation terminal (which may be hereafter
abbreviated as "GOT") is attached on the panel face of a
control panel or an operation panel, and connected to a
program connector in an FX or A Series programmable
controller (which may be hereafter abbreviated as "PLC")
(except the A0J2) inside the control panel.
Not only the CPU port connection method but also the
computer link port connection method is available so that
the GOT can be connected to a PLC other than MELSEC
or a micro computer board.
You can monitor various devices and change the data of
the PLC while checking the screen of the GOT.
There are several display screens built in the GOT which
offer various functions. In addition, you can create display
screens.
The built-in screens (system screens) and the screens
made by the user (user screens) have the following func-
tions respectively.
FX or
A Series PLC
Program
connector
GOT main body

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-3
User screens
1) Screen display function
The screens created by the user can be displayed. The following functions can be assigned
to each screen. And the screens to be displayed can be limited using the security function.
a) Display function
-Up to 500 screens created by the user can be displayed. The screens can be created
using the FX-PCS-DU/WIN-E V2.00 for the DU or using the SWoD5C-GOTRE-PACK
("o" indicates a numeric not less than 1.) for the GOT. Two or more screens can be
overlaid or changed over.
-Not only characters such as alphabets, numerics, Hiragana, Katakana and Kanji but
also simple graphics such as straight lines, circles and rectangles can be displayed. In
the F940GOT-SWD-E, screens can be displayed in 8 colors.
b) Monitor function
-Set values and current values of word devices in the PLC can be displayed in numerics
or bar graphs for monitoring.
-The specified range of the screen can be displayed reversely in accordance with the
ON/OFF status of bit devices in the PLC.

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-4
c) Data change function
-The numeric data being monitored can be changed.
d) Switch function
-By manipulating the operation keys in the GOT, bit devices in the PLC can be set to ON
and OFF. The display panel face can be assigned as touch keys to offer the switch func-
tion.
Make sure to press a touch key by fingers.
If a touch key is pressed by a hard or sharp object, it may become failed.

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-5
System screens
1) Monitor function
a) List program (only in the FX Series)
- Programs can be read, written and monitored in the form of instruction list program.
b) Buffer memory (only in the FX2N and FX2NC Series)
-The contents of buffer memories (BFMs) of special blocks can be read, written and
monitored.
c) Device monitor
-The ON/OFF status of each device and the set value and the current value of each
timer, counter and data register in the PLC can be monitored and changed.
-Specified bit devices can be forcedly set to ON and OFF.
Different from the monitor function in the screen display function described in the previ-
ous page, the screen can be displayed only inputting a desired device No. from the key-
board.

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-6
d) Data sampling function
The current value of specified data registers are acquired in a constant cycle or when the
trigger condition is satisfied.
-The sampling data can be displayed in the form of list or graph.
-The sampling data can be output to a printer in the form of list.
e) Alarm function
Alarm messages can be assigned to up to 256 consecutive bit devices in the PLC.
When a bit device becomes ON, the assigned message is displayed (overlapped) on the
user screen.
In addition, a specified user screen can be displayed by setting a corresponding bit
device to ON.
-When a bit device becomes ON, a corresponding message is displayed on the user
screen. The message list can be also displayed.
-Up to 1,000 alarms (turning ON of bit devices) can be stored as the alarm history.
-The number of alarms occurred in each device can be stored.
*As to 2], the alarm history can be output to a printer using the screen creation soft-
ware.

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-7
f) Other functions
Many other functions are built in.
-The real-time clock is built in, and the current time can be set and displayed.
-The GOT can function as an interface to enable data communication between the PLC
and a personal computer in which the relay ladder creation software is started up. At
this time, the GOT screen can be displayed also.
-The screen contrast and the buzzer sound volume can be adjusted.

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-8
1.2 Product configuration
The GOT is equipped with accessories (1) to (3) below.
Parts (4) to (8) are offered as options.
1) F940GOT (main body)
F940GOT-SWD-E: 5.7" STN type LCD (with eight colors)
F940GOT-LWD-E: 5.7" STN type LCD (with black and white)
2) Metal fixtures
Metal fixtures used to attach the GOT to a control panel
- Metal fixture 6 pieces
- Tightening bolt 6 pieces (M3 x 20)

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-9
3) Packing
Packing to prevent dusts and water
Used to attach the GOT to a control panel

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-10
Optional parts
4) Software to create user screens (3.5" FD)
FX-PCS-DU/WIN-E V2.10 or later
(in accordance with the Windows95)
SWoD5C-GOTRE-PACK
("o" indicates a numeric not less than 1.)
(in accordance with the Windows95 and the WindowsNT)
5) Connection cable FX-40DU-CAB (3 m, 9.84 ft)
Connection cable FX-40DU-CAB-10M (10 m, 32.81 ft)
Connection cable FX-50DU-CABL
(3m, 9.84 ft, with L-shape connector on the GOT side)
Each of them is an optional cable to connect the GOT and the
FX/FX2C/A Series PLC.

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-11
6) Connection cable FX-50DU-CAB0 (3 m, 9.84 ft)
Connection cable FX-50DU-CAB0-1M (1 m, 3.28 ft)
Connection cable FX-50DU-CAB0-10M (10 m, 32.81 ft)
Connection cable FX-50DU-CAB0-20M (20 m, 65.62 ft)
Connection cable FX-50DU-CAB0-30M (30 m, 98.43 ft)
Connection cable FX-50DU-CAB0L
(3 m, 9.84 ft, with L-shape connector on the GOT side)
Each of them is an optional cable to connect the GOT and
the FX0/FX0S/FX0N/FX2N/FX2NC Series PLC.
By using either one, the GOT can be directly connected to
the PLC.
7) Two-port interface FX-2PIF
This is an optional interface to use the GOT and a periph-
eral unit to create sequence programs at the same time.
This is not required when the GOT is connected to a gener-
alpurpose personal computer or connected to a peripheral
unit via a computer link unit.

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-12
8) Battery PM-20BL (spare part)
This is used to back up the alarm history data, the real-time
clock, etc.
This is attached when the GOT is delivered.
9) EPROM memory to store the user screen data FX-EPROM-
4M
This is an optional EPROM memory (M27C4002-**F (4 MB)
manufactured by SGS-THOMSON) to save the user screen
data.
The user screen data can be written using a general-pur-
pose ROM writer connected to the screen creation soft-
ware.