ML Accessories Knightsbridge BT9H4/6K Instruction Manual

1
INSTALLATION & MAINTENANCE MANUAL
BT9H4/6K BT14H4/6K BT20H4/6K
ACCESSORIES LTD ACCESSORIES LTD
ACCESSORIES LTD
02

2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
BT9H4/6K / BT14H4/6K / BT20H4/6K
INSTALLATION
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, please consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• This product is Class III
• Remove the three fastening screws securing the LED plate (see Fig. 2)
This product is designed as a retrofit gear tray compatible with the following products:
BT9/14/20CT, BT9/14/20CTS, BT9/14/20CTEM, BT9/14/20CTEMS
• Remove the diffuser on the BTXXCT luminaire by rotating bezel anti-clockwise (see Fig. 1)
Fig. 1
Fig. 2
BT14H4K
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
BT14H4K
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, please consult a qualified electrician.
•Please isolate mains prior to installation or maintenance
•This product is Class III
•This product is non-dimmable
INSTALLATION
This product is designed as a retrofit gear tray compatible with the following products:
BT14CT, BT14CTS, BT14CTEM, BT14CTEMS
•Remove the diffuser on the BT14CT luminaire by rotating bezel anti-clockwise (see Fig. 1)
Fig. 1
•Remove the three fastening screws securing the LED plate (see Fig. 2)
Fig. 2
•Unplug the 2-pin connectors from the LED plate and replace the LED plate with the BT14H4K
•Plug the 2-pin connectors into the YJ / DC sockets as required. Insert the indicator LED into the
LED holder if required (see Fig. 3)
Remove screws
BT14H4K
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
BT14H4K
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, please consult a qualified electrician.
•Please isolate mains prior to installation or maintenance
•This product is Class III
•This product is non-dimmable
INSTALLATION
This product is designed as a retrofit gear tray compatible with the following products:
BT14CT, BT14CTS, BT14CTEM, BT14CTEMS
•Remove the diffuser on the BT14CT luminaire by rotating bezel anti-clockwise (see Fig. 1)
Fig. 1
•Remove the three fastening screws securing the LED plate (see Fig. 2)
Fig. 2
•Unplug the 2-pin connectors from the LED plate and replace the LED plate with the BT14H4K
•Plug the 2-pin connectors into the YJ / DC sockets as required. Insert the indicator LED into the
LED holder if required (see Fig. 3)
Remove screws
GENERAL INSTRUCTIONS
SAFETY

WARNING
GENERAL
WARRANTY
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will
invalidate the warranty. If this product should fail within its warranty period it should be returned to the
place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for
any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
• Unplug the 2-pin connectors from the LED plate and replace the LED plate with the BT14H4K
• Plug the 2-pin connectors into the YJ / DC sockets as required. Insert the indicator LED into the LED
holder if required (see Fig. 3)
• Refasten the LED plate screws
• Reattach the diffuser by rotating clockwise
• Switch on and check for correct operation
3
Fig. 3
•Refasten the LED plate screws
•Reattach the diffuser by rotating clockwise
•Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the
warranty. If this product should fail within its warranty period it should be returned to the place of purchase for a
free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated
with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter
product specification without prior notice.
Plug in leads and LED
indicator as required
Fig. 3

4
ML Accessories Limited
LU5 4LT
www.mlaccessories.co.uk AKMAR19_V1
ACCESSORIES LTD ACCESSORIES LTD
ACCESSORIES LTD