Mo-vis Foot Control Omni User manual

moving forward together
Foot Control
Foot Control Omni (P021-51) - Foot Control LiNX (P021-53)
Installation manual
Edition D-P021-51-70-M1-0300, August 2023

Contents
Contents About this manual .............................................................................. 4
Installation manual ................................................................... 4
mo-vis bv ................................................................................... 4
Distributor .......................................................................................... 5
Important information ........................................................................ 6
Warranty ............................................................................................ 7
Repair and replacement ............................................................ 7
Amendments ............................................................................. 7
Disclaimer and limitations of remedies .................................... 8
Voiding of warranties ................................................................ 8
Technical support ................................................................................ 9
Warning labels .................................................................................. 10
Limited liability ................................................................................. 13
Preparations ..................................................................................... 14
Qualified service engineer ...................................................... 14
1

Tools ........................................................................................ 14
Installation plan ...................................................................... 15
Installation ....................................................................................... 16
Operation ......................................................................................... 20
LED status ................................................................................ 20
Configuration .................................................................................... 22
Software download ................................................................. 22
Defining parameter settings ................................................... 23
Parameter settings .................................................................. 23
Testing .............................................................................................. 38
Check the device for intactness .............................................. 38
Operational test ...................................................................... 38
Test drive ................................................................................. 39
Stop test .................................................................................. 40
First time use .................................................................................... 41
Maintenance .................................................................................... 43
Monthly inspection ................................................................. 43
Yearly inspection ..................................................................... 43
Error codes ....................................................................................... 44
2

Omni Joystick Connection ................................................................. 48
Purpose ................................................................................... 48
Connectivity ............................................................................ 48
Features .................................................................................. 49
Other information ................................................................... 49
R-net Joystick Connection ................................................................. 50
Purpose ................................................................................... 50
Connecting the R-net communication cable ........................... 50
R-net parameters .................................................................... 51
R-net trip codes ....................................................................... 52
Supported R-net parameters .................................................. 52
Other information ................................................................... 55
LiNX Joystick Connection .................................................................. 57
Purpose ................................................................................... 57
Connectivity ............................................................................ 57
LiNX parameters ...................................................................... 57
Sensor LED ........................................................................................ 58
Technical Data ................................................................................... 60
Product description & code .................................................... 60
Interface connectors ............................................................... 60
Joystick connectors ................................................................. 60
Operating forces ...................................................................... 61
3

About this manual
Installation manual
This manual contains useful and important information about your device.
Please read it carefully before use and store safely for future reference.
Our team will be happy to answer your questions.
mo-vis bv
Biebuyckstraat 15D . 9850 Deinze .
Belgium
http://www.mo-vis.com .
cont[email protected] . [phone]
60
CH-REP: SKS Rehab AG, Im Wyden,
8762 Schwanden GL, Switzerland.
UK Responsible Person: QServe
Group UK, Ltd., 49 Greek Street,
London, WID 4EG, UK.
4
4 Foot Control Installation manual

Distributor
This product is distributed by Stealth Products, LLC.
Stealth Products, LLC
104 John Kelly Drive, Butnet, TX
78611
Phone: [phone] Toll Free:
1(800) 965-9229
Fax: [phone] Toll Free: 1(800)
806-1225
[e-mail]
www.stealthproducts.com
5
Foot Control Installation manual 5

Important information
CAUTION: Incorrect use or installation may lead to risk of injury to
the user and damage to the wheelchair or other property. In order
to reduce these risks, you should carefully read this manual, paying
particular attention to the safety instructions and warning texts.
NOTICE: Only install this product on a wheelchair where the wheelchair
manufacturer allows the installation of third party parts.
6
6 Foot Control Installation manual

Warranty
mo-vis bv warrants the product to be free from defects in material and
workmanship for a period of 2 years under proper use, care and service. The
dealer should never keep mo-vis products in stock for a period more than 6
months prior to delivery to the end-user. mo-vis' warranty will never exceed a
period of 2 years and 6 months after shipment.
All warranties do not extend beyond the initial purchaser from an authorized
mo-vis dealer or mo-vis itself.
Repair and replacement
For warranty service, contact your dealer (or us if bought directly). In the
event of a defect in material or workmanship, the dealer or customer must
obtain a Return Merchandise Authorization (RMA) number from us. The
product must be shipped to a service centre designated by mo-vis. mo-vis will
repair or, at mo-vis’ option, replace any product covered by the warranty.
Amendments
No person is authorized to alter, extend or waive the warranties of mo-vis.
7
Foot Control Installation manual 7

Disclaimer and limitations of remedies
The express warranties set forth in this agreement are in lieu of all other
warranties of merchantability or fitness of purpose. In no event shall mo-
vis be liable for any direct, indirect, incidental or consequential damages
resulting from any defect in this product.
Warranty of parts subject to “normal wear and tear” (e.g. joystick handles,
pads, …) are not covered in the warranty except as it applies to defects in
material or construction.
Voiding of warranties
The foregoing warranties are contingent upon the proper installation, use,
maintenance and care of the product. The warranty will be void if the product
has been installed or used improperly, or if it has been repaired or any part
replaced by persons other than mo-vis or an authorized dealer. This product
is considered as a non-serviceable part.
The addition of equipment or features that are not manufactured or
recommended by mo-vis could affect the intended function of the mo-vis
product and may invalidate the warranty.
8
8 Foot Control Installation manual

Technical support
TROUBLE:
In case of technical problems:
1 Contact mo-vis at [e-mail] or [phone].
2 Always state the device serial number when contacting us. This
ensures you are provided with the correct information.
9
Foot Control Installation manual 9

Warning labels
Please read this manual, the safety instructions and warning texts carefully,
in order to reduce the risks associated to the device. Our products are safe
under normal and reasonably foreseeable operating conditions.
NOTE: This symbol indicates general notes and information.
CAUTION: This symbol indicates caution for a hazardous situation that,
if not avoided, could result in minor or moderate injury.
WARNING: This symbol indicates a warning for a hazardous situation
that, if not avoided, could result in death or serious injury.
Other labels:
Catalogue number: indicates the
manufacturer's catalogue number
so that the medical device can be
10
10 Foot Control Installation manual

identified.
Batch code: indicates the
manufacturer's batch code so that
the batch or lot can be identified.
Medical device: indicates that the
item is a medical device.
Date of manufacture: indicates the
date when the medical device was
manufactured.
Serial number: indicates the
manufacturer's serial number so
that a specific medical device can be
identified.
Consult instructions for use or con-
sult electronic instructions for use:
indicates the need for the user to
consult the instructions for use.
Keep dry: indicates a medical device
that needs to be protected from
moisture.
Do not use if package is damaged
and consult instructions for use:
11
Foot Control Installation manual 11

indicates that a medical device
should not be used if the package
has been damaged or opened and
that the user should consult the
instructions for use for additional
information.
CE label: indicates that the manufac-
turer or importer affirms the good's
conformity with European health,
safety, and environmental protec-
tion standards.
WEEE: indicates that the product
should not be discarded as unsorted
waste but must be sent to separate
collection facilities for recovery and
recycling.
Manufacturer: indicates the medical
device manufacturer.
12
12 Foot Control Installation manual

Limited liability
mo-vis accepts no liability for personal injury or damage to property
that may arise from the failure of the user or other persons to follow the
recommendations, warnings and instructions in this manual.
CAUTION: Carry out only the service and maintenance activities
specified in this manual, as long as you comply with the demands
stated in this manual for a specific action. In case of doubt, contact mo-
vis.
WARNING: The device should always be tested without any person
sitting in the wheelchair after every alteration of the physical
installation or adjustment of the parameters.
13
Foot Control Installation manual 13

Preparations
CAUTION: Before you start with the installation:
• Please check the packaging and verify that all items are included.
• Make sure that you have all the necessary documentation and
knowledge to install this device.
• Check the condition of the device.
Qualified service engineer
Only a qualified service engineer may install the device.
CAUTION: An incorrect programming of the wheelchair electronics may
cause damage to the devices, or injury to the user.
Tools
Use an Allen wrench to install the device.
CAUTION: Use proper tools to install and adjust the device. The use of
improper tools may cause damage to the device.
14
14 Foot Control Installation manual

Installation plan
Set up an installation plan before beginning the installation. Based on the
users' needs and capabilities, this plan should take into account:
• Where which part of the device should be placed.
• How the device will be operated.
• A robust and reliable positioning. Hard or sudden movements of the
wheelchair may not disorganize the installation.
WARNING: Protect the device against bumps. Mind damaging the
unit and wiring. Make sure that cabling is mounted in such a way that
excessive wear and tear is avoided.
WARNING: Do not use the control as only support for hands or limbs.
Movements and shocks may disrupt controls.
15
Foot Control Installation manual 15

Installation
1 Place the foot on the Foot Control and decide where you want to
position the 4 pins. Use an Allen key to fixate the pins at the desired
position. We also advise you to use the strap, so consider mounting the
Foot Control Strap Mounting Plate as well.
NOTE: The pivot point of the Foot Control is located more towards
the ankle for ergonomic reasons. You can adjust the pivot point, by
sliding the pins more in/out at the toes or the ankle.
CAUTION: Tighten the screws firmly, but not excessively. Excessive
force may damage the unit.
2 Define the position of the Foot Control.
Will you mount the Foot Control on an existing foot plate or will you use
a designated bracket for the Foot Control? You can use the dedicated
mounting holes if needed (orange in picture below).
16
16 Foot Control Installation manual

CAUTION: Mount the pedal on a rigid structure, to avoid fracture.
CAUTION: It is very important to consider the ideal sitting position,
before installing the Foot Control. Without stability, there can be
no good function.
17
Foot Control Installation manual 17

CAUTION: Make sure that there are no objects or people within
the movement range of the Foot Control, to avoid pinching.
3 Consider using the Foot Control Safety Bracket Set. You can mount this,
by using the red holes in the picture above.
4 Place and secure the interface unit and all cabling on the wheelchair.
WARNING: Place the Interface unit with the connectors facing
downwards. This is to prevent water from entering the Interface
unit.
5 Place a power on/off (pwr) and/or mode (in) switch, secure their cabling
and insert their connections. You can use the connections on the
Interface unit.
CAUTION: Before inserting a connector, remove the protective
cover. If the connections are not used, always put or keep the
protective covers in.
CAUTION: This is Class I Medical Device (MDR 2017/745). All
accessories, including switches, must also comply with the MDR
2017/745 regulations (e.g. the mo-vis Twister, tested according to
EN12184 standards).
6 Connect the cabling to the wheelchair electronics.
18
18 Foot Control Installation manual

CAUTION: All wheelchair electronics must be switched off during
installation.
CAUTION: Make sure that the Foot Control is moved away for transfers.
The maximum force requirements on the Foot Control are 100 kgs in a
horizontal plane and 130 kgs in a vertical plane.
CAUTION: Make sure that the driving function is off, when the Foot
Control is not being used to drive. This will allow the user to rest his/
her foot, without causing unwanted movements.
19
Foot Control Installation manual 19