Modena BH 3648 IRR Owner's manual

User
Manual Book
Built –in Gas Hob
BH 3648 IRR

2
TABLE OF CONTENTS
SAFETY & WARNING 3
Important Warnings 3
FEATURES 5
INSTALLATION 7
HOW TO USE 15
Usage of Gas Hob 15
MAINTENANCE 19
TROUBLESHOOTING 20
SPECIFICATIONS 21
This guide book explains everything you need to know about your new
product. Please contact our Customer Care should you need further
assistance through www.modena.com.

3
Important Warnings
Before touching the connection terminals, all supply circuit
should be disconnected.
Any in advertent cooking made with fats and oils can be
dangerous and cause fire.
Risk of fire; do not store the food materials on the cooking
surface.
During usage, the reachable sections can be hot. Keep children
away.
The setting conditions of this appliance is indicated on the label.
This appliance is not connected to a combustion product
discharge system. This appliance shall be connected and
installed as per the applicable installation legislation. Consider
the requirements related with ventilation.
Using a gas hob will release humidity and combustion products
in the room where it resides. Especially during appliance in use,
ensure that the kitchen is well ventilated and retain the natural
ventilation holes or install a mechanical ventilation system.
(Hood on top of the oven) Sustained usage of the appliance may
require additional ventilation. For example, opening a window or
if available, increasing the ventilation level of a mechanical
ventilation system.
The appliance is intended for cooking only. It must not be used
for other purposes like room heating.
This appliance should be installed as per regulations and in well
ventilated location only. Read the instructions before installing or
operating the appliance.
Before placing the appliance check the local conditions (gas type
and gas pressure) and ensure that the settings of the appliance
are appropriate.
These instructions are applicable for countries of which symbols
are indicated on the appliance. If the country symbol is not
available on the appliance, in order to adapt the appliance to the
SAFETY & WARNING

4
conditions of such country, the technical instructions should be
read.
Do not operate the system for more than 15 seconds. If the
burner does not ignite at the end of 15 seconds stop the
operation of the system and open the section door and/or wait
for at least 1 minute before igniting the burner.
Do not use steam cleaners to clean the appliance.
NEVER try to extinguish a fire with water. First disconnect the
mains supply and then using, for example a lid or blanket, cover
the fire.
Unless continuous supervision is provided, the children of age 8
or below should be kept away.
Pay attention for not to touch the heating elements.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.

5
1. Burner positions
2. Glass or Metal Surface
3. Control Buttons
4. Small Burner
5. Medium Burner
6. Large Burner
7. WOK Burner
8. Hotplate
9. Coffee Adaptor
10. Wok Burner Adaptor
11. Cast Grill
12. Enamel Grill
FEATURES

6
Control Panel
Hob Panel Visual of 60 cm

7
If Built-In Oven is Placed Under Hob
1. Gas pipe
should be affixed in
a way not to touch
the oven below,
sharp edges and
corners, not to be
pulled in a manner
to be twisted and
strained.
2. Make gas connection from right part of the Hob, fasten the hose
by use of clamp.
Installation of Hobs
1. Detach the burners, burner hoods and grills from the product.
2. Turn the Hob down and place on smooth ground.
3. In order to prevent entrance of foreign substances and liquids
between Hob and counter, apply the paste given in package to
the sides of lower guard of counter. For corners, curl paste and
increase curls till filling corner gaps.
4. Turn Hob again and align with and place on counter.
5. Fasten up your Hob on counter by using the clamp and screws
supplied. On the assembly chart given in next page, it is shown
how to assemble your hob.
INSTALLATION
Figure 1
Cooktop
Hose
Oven

8
6. When product is mounted on a drawer, if it is possible to touch
lower side of product, this section should be separated with a
wooden shelf.
7. While mounting Hob on a closet, as shown in the figure above, in
order to separate between closet and Hob, a shelf should be
mounted. If it is mounted on a built-in oven, there is no need to
do that.
8. If your Hob will be mounted next to right or left wall, the minimum
distance between wall and Hob should be 50 mm.
Counter Cutting Sizes and Installation of Your Hob
Figure 2

9
Pay attention to the drawings and dimensions given below while
making Hob installation and adjusting counter cutting sizes.

10
Correct Place for Installation
 Product is designed in accordance with the kitchen counters
supplied from market. A safe distance should be left between
the product and kitchen walls and furniture.
 If hood/aspirator will be installed over your appliance, obey to
the recommendation of hood/ aspirator manufacturer for
assembly height. (min. 65 cm)
 The gap that Hob is to be placed on the counter should be
cut in line with Hob installation dimensions.
 For installation of the product, the rules specified in local
standards related to electricity should be complied.

11
Ventilation of Room
The air needed for burning is received from air available in the area
and the gases emitted are given directly in room. For safe operation
of your product, good ventilation is needed. If there is no available
window or area to be utilized for ventilation, additional ventilation
should be installed. However, if the room has a door opening to
outside area, additional vent holes is not required.
Transformation from Natural Gas to LPG and from LPG to Natural
Gas
1. Turn off gas and electricity of the Hob. If your Hob is hot, wait
for cooling down.
2.
For injector change, use a screwdriver whose edge is as the
Figure 4.
3.
As seen in Figure 5, demount burner lid and burner of the Hob
and ensure visibility of injector.
4.
Remove injector by turning as shown in Figure 6 with
screwdriver and replace it with a new one.
Room Size Ventilating Opening
Smaller than 5m³ min. 100 cm²
Between 5 m³- 10 m³ min. 50 cm²
Bigger than 10m³ no need
In basement or cellar min. 65 cm²
Figure 4
Figure 5
Figure 6

12
5. After that, detach control switches of the Hob. Make setting
by turning the screw in the middle of gas valve with a small
screwdriver in the manner shown in the following picture. To
adjust flow rate screw, use a screwdriver having suitable
dimension. For LPG, turn the screw clockwise. For natural gas,
turn the screw one time counter clockwise. At low position,
length of normal flame should be 6-7 mm. For the last control,
check out whether flame is open or closed. Setting of your
appliance may different according to the type of gas valve
used.
Gas Breaking Safety Appliance (FFD)
Against putting out to be taken place as a result of liquid overflow at
upper burners, safety appliance steps in and cut gas immediately.
Gas Connection and Safety
• For LPG (cylinder) connection, affix metal clamp on the hose
coming from LPG cylinder. Affix an edge of the hose on hose
inlet connector behind the appliance by pushing to end
through heating the hose in boiled water. Afterward, bring the
clamp towards end section of the hose and tighten it with
screwdriver. The gasket and hose inlet connector required for
connection is as the picture shown below
.
Figure 7
Figure 8
Figure 9

13
•
Natural gas connection should be done by authorized service.
For natural gas connection, place gasket in the nut at the
edge of natural gas connection hose. To install the hose on
main gas pipe, turn the nut. Complete the connection by
making gas leakage control.
NOTE!
The regulator to be affixed on LPG cylinder should have 300 mmSS
feature.
Main Gas Pipe
Gasket
Hose Inlet Connector
Metal Clamp
Lpg Connection Hose
Main Gas Pipe
Gasket
Natural Gas Connection Hose
Nut

14
•
Connect your appliance to gas valve from the shortest way
and in a manner to prevent any leakage. For safety, the hose
used should be maximum 125 cm and minimum 40 cm.
•
While making gas leakage control; never use lighter,match,
glowing cigarette or similar inflammable matter.
•
Apply soap bubble on connection point. If any leak/leakage
exists, foaming will occur on soaped region.
•
If the Hob is to be mounted on a cabinet or openable drawer,
a heat protection panel having 15 mm minimum opening
should be mounted under the Hob.
Electrical Connection and Safety
• Make sure that your Hob already configured in accordance
with electrical supply of 220-240V, 50/60Hz for automatic
ignition purposes.
WARNING!
Gas hose and electric connection of the appliance should
not pass next to hot areas such as back of the appliance. Gas hose
should be connected by making wide angle turns against breaking
possibility. Movement of appliance whose gas connection is made
may cause gas leakage.
.
True
True
True
False

15
Usage of Gas Hob
1. Before starting to use your Hob, be sure burner cap are at
correct position. Correct placement of burner hoods is shown
in the following figure.
2. Gas valve have a special locking mechanism. Therefore, to
operate Hob zone, press button by pushing ahead and while
opening or closing the valve, hold down the button.
3.
For automatic igniting models, igniting is realized via
electricity. Therefore, before operating appliance, be sure
that appliance has electric connection.
HOW TO USE
Figure 10
Figure 11

16
4. Igniting for these models is as follows:
- Hob valve is at closed position.
- To ignite Hob firstly press the button towards ahead.
- While holding down the button, lighter steps in and starts
to ignition.
- By turning the button right while holding down, you can
provide ignition at flame length you want.
NOTES:
• Pay attention that Hob grills are placed on Hob table
completely. In case of failure about this matter can cause
pouring of the materials to be put on that.

17
• For the models having gas putting out safety, following
realizing ignition procedure according to the guidelines
above, wait for 5-10 seconds by pushing button ahead
without keeping your hands off. Safety mechanism will step
in this
duration and ensures operation of the Hob. With regard
to gas putting out appliance, gas valve cuts the gas going to
Hob zone in case of putting out of Hob flame due to any
reason.
•
While using coffee pot apparatus supplied along with the Hob,
be sure that foots of apparatus are placed on Hob grill exactly
and remain on Hob zone in centered way. Use the apparatus
only on small burner.
•
While utilizing gas Hobs, use saucepan, placed on Hob
surface as far as possible. In the following table, cooking pot
diameters recommended to be used as per burners are given.
Characteristic of Wok Hob zone is to cook quickly.
Pot Diameter
METAL HOBS
Domino 45 cm
Hobs
60 cm
Hand
Control
60 cm
Control
Front
70 cm
Control
Front
90 cm
Control
Front
Small
Burner
12-18cm 12-18cm 12-18cm 12-18cm 12-18cm 12-18cm
Middle
Burner
- 18-20cm 18-20cm 18-20cm 18-20cm 18-22cm
Big
Burner
18-22cm 22- 24cm 22-26cm 22-24cm 22-24cm 22-26cm
Wok
Burner
24-26cm 24-26cm 24-26cm 24-26cm 24-26cm 26-32cm

18
Cooking pot to be used with products should have minimum 120 mm
diameter.
Wok Burner
As it possesses double ring flame system, it gives
homogenous heat distribution at the bottom of
cooking pot at high temperature. It is ideal for
short term and high temperature cooking. When
you want to use regular cooking pot on wok
burner, it is necessary that you remove wok
cooking pot carrier from Hob.
False
False
False
True
Figure 12

19
• Before starting cleaning the hob, first unplug the plug
supplying electricity to Hob and turn off gas valve. If Hob is
hot, wait for it to cool down.
•
Regular cleaning and maintenance should be performed on
your Hob for longer durability.
•
Do not clean your Hob with scratching tools such as bristle
brush, wire wool or knife. Do not use abrasive, scratching,
acid materials or detergent.
•
Clean parts of your Hob using soapy cloth, rinse it, later rinse
well with a soft cloth.
•
Clean glass surfaces with special glass cleaning substances.
As scratching of glass surfaces leads to breaking, while
cleaning glass surfaces, do not use abrasive cleaners or sharp
metal scrapers.
•
Do not clean your Hob with steamy cleaners.
•
Clean channels and lids of Hob zones with soapy water and
clean gas channels with a brush.
•
In the course of cleaning your Hob, never use flammable
materials such as acid, thinner and gas.
•
Do not wash plastic and aluminium parts of your Hob in
dishwasher.
•
Clean your Hob immediately when there is a spill of vinegar,
lemon, salt, coke and similar acid and alkaline containing
substances.
•
After a long time of usage, sometimes Hob buttons can be
difficult to use. In such circumstances, it may be necessary
that the buttons to be changed. The change should only be
done by authorized service center or appointed technician.
MAINTENANCE
Figure 13
Figure 14
Figure 15

20
You can solve the troubles you encounter at your product by checking
the following points before calling technical service.
If Hob Does Not Operate
• Check if power cable of Hob is plugged in.
•
Examine with safe ways if electric exists on network.
•
Audit fuses.
•
Control whether damage is available on power cable.
•
Check if main gas valve in your network is open.
•
Go through existence of breaking or twisting on gas pipe.
•
Be sure that gasp pipe is connected to Hob in appropriate
way.
•
See over if suitable gas valve is used for your Hob (Get
periodical maintenance done)
If Starter Does Not Operate
• Be sure that electric power cable of product is plugged in.
•
Clean the edge and body sections of ignition spark plugs
found on burners with a wet and dirt remover material
thoroughly. Be sure that the channels present on burners are
open and clean.
•
Setting Gas Hobs as per Gas Type
•
Gas type (LPG or natural gas) that your appliance is
manufactured for is stated in the label found behind the
product and that show technical features. If gas setting of
your appliance is not the same as gas setting of your network,
it should be adjusted by making change by anexpert person.
The hobs are designed to operate with a monophase alternating current
of 220-240V ~ 50Hz. Before the installation of the appliance, we
suggest you to check always the specifications on the rating label
applied on the front bottom side of the hob.
TROUBLESHOOTING