Modena BI 0321 L Owner's manual

User
Manual Book
Built In Induction Hob
Magne Series
BI 1325, BI 1935
BI 1725, BI 1625 F, BI 1321
BI 1721, BI 0321 L, BI 0721 L

TABLE OF CONTENTS
Part 1: Safety Warnings 3
Part 2: Name of Parts 6
Part 3: Installation 11
Part 4: How to Use 15
Part 5 : Maintenance 27
Part 6: Troubleshooting 30
Part 7: Precaution 30
Part 8: Specification 31
This guide book explains everything you need to know about your new
product. Please contact our Customer Care should you need further
assistance through www.modena.com

3
Safety Warnings
Your safety is important to us. Please read the following information carefully
before installing or using your Hob.
Electrical Shock Hazard
•Disconnect the appliance from the electricity supply before carrying out any
work or maintenance on it.
•Make sure that grounding system is installed properly.
•Alterations to the domestic wiring system must only be made by MODENA
Technician.
•Failure to follow this advice may result in electrical shock or death.
Cut Hazard
•Take care - panel edges are sharp.
•Failure to be cautious could result in injury or cuts.
Important Safety Instructions
•No combustible material or products should be placed on the appliance at any
time.
•In order to avoid a hazard, this appliance must be installed according to these
instructions for installation.
•This appliance is to be properly installed and grounded only by MODENA
Technician by contacting MODENA Customer Service.
•This appliance should be connected to a circuit which incorporates an isolating
switch providing full disconnection from the power supply.
•Failure to install the appliance correctly could invalidate any warranty or liability
claims.
Operation and Maintenance
Electrical Shock Hazard
•Do not cook on a broken or cracked hob. If the hob surface break or crack,
switch the appliance off immediately at the mains power supply (wall switch)
and contact MODENA technician.
•Switch the hob off at the wall before cleaning or maintenance.
•Failure to follow this advice may result in electrical shock or death.
PART 1: SAFETY WARNINGS

4
Health Hazard
•This appliance complies with electromagnetic safety standards.
•However, persons with cardiac pacemakers or other electrical implants (such as
insulin pumps) must consult with their doctor or implant manufacturer before
using this appliance to make sure that their implants will not be affected by the
electromagnetic field.
•Failure to follow this advice may result in death.
Hot Surface Hazard
•During usage, accessible parts of this appliance will become hot enough to
cause burns.
•Do not let your body, clothing or any item other than suitable cookware contact
the ceramic glass until the surface is cooled down.
•Keep children away from the appliance.
•Handles of saucepans may be hot to touch. Check saucepan handles, do not
overhang other cooking zones that are on. Keep handles out of reach of
children.
•Failure to follow this advice could result in burns and scalds.
Cut Hazard
•The razor-sharp blade of a hob scraper is exposed when the safety cover is
retracted. Use with extreme care and always store safely and out of reach of
children.
•Failure to be cautious could result in injury or cuts.
Important Safety Instructions
•Never leave the appliance unattended when in use. Boil over causes smoke and
greasy spillovers may ignite fire.
•Never use your appliance as a work or storage surface.
•Never leave any objects or utensils on the appliance.
•Do not place or leave any magnetisable objects (e.g. credit cards, memory
cards) or electronic devices (e.g. computers, MP3 players) near the appliance,
as they may be affected by its electromagnetic field.
ATTENTION
Metallic objects such as knives, forks, spoons and lids should not
be placed on the hob surface since they might get hot.

5
•Never use your appliance for warming or heating the room.
•After use, always turn off the cooking zones and the hob as described in this
manual (i.e. by using the touch controls). Do not rely on the pan detection
feature to turn off the cooking zones when you remove the pans.
•Do not allow children to play with the appliance or sit, stand, or climb on it.
•Do not store items of interest to children in cabinets above the hob. Children
climbing on the hob could be seriously injured.
•Do not leave children alone or unattended in the area where the appliance is in
use.
•Do not repair or replace any part of the appliance unless specifically
recommended in the manual. All other repairing process should be done by
MODENA technician.
•Do not use steam cleaner to clean hob.
•Do not place or drop heavy objects on hob.
•Do not stand on your hob.
•Do not use pans with jagged edges or drag pans across the ceramic glass surface
as this may scratch the glass.
•Do not use scourers or any other harsh abrasive cleaning agents for cleaning, as
these can scratch the ceramic glass.
•If the power supply cable is damaged, it must only be replaced by MODENA
technician.
•This appliance is intended to be used in household and similar applications such
as: staff kitchen areas in shops, offices and other working environments; farm
houses; by clients in hotels, motels and other residential type environments;
bed and breakfast type environments.
•This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be done
by children without supervision.
WARNING!
•Unattended cooking on a hob with fat or oil can be dangerous and
may result in fire. NEVER try to extinguish fire with water, but
switch off the appliance and then cover flame with a lid or a fire
blanket.
•The appliance is not intended to be operated by means of an
external timer or separate remote-control system.

6
MODEL: BI 1325
1. Glass Plate
2. 2000W Cooking Zone
3. 1500W Cooking Zone
4. Control panel
Control Panel
1. Cooking Zone selection button
2. Stop & Go control button
3. Timer control button
4. Heating level/Timer slider control
5. Child Lock control button
6. ON/OFF button
PART 2: NAME OF PARTS

7
MODEL: BI 1625 F
1. 1500W boost 2000W Cooking Zone
2. 2000W boost 2600W Cooking Zone
3. 3000W boost 3600W Flexi area-Left
4. 2000W boost 2600W Cooking Zone
5. 1500W boost 2000W Cooking Zone
6. 3000W boost 3600W Flexi area-Right
7. Glass plate
8. Control panel
Control Panel
1. Cooking Zone selection button
2. Booster function control button
3. Stop & Go control button
4. Timer control button
5. Left Flexi zone control button
6. Right Flexi zone control button
7. Heating level/Timer slider control
8. Child Lock control button
9. ON/OFF button

8
MODEL: BI 1725
1. 2000W induction Zone
2. 2000W induction Zone
3. Ceramic Glass
4. Control panel of cooking zone #1
5. Control panel of cooking zone #2
Control Panel
1. Booster function control button.
2. Stop & Go control button
3. Timer control button
4. Heating level/Timer adjusting slider
5. Child Lock control button
6. ON/OFF button

9
MODEL: BI 1935
1. 2000W booster 2200W Induction Zone
2. 1300W booster 1500W Induction Zone
3. 2000W booster 2200W Induction Zone
4. EuroKera Glass
5. Control panel
Control Panel
1. Booster function control button
2. Cooking Zone selection button
3. Child Lock control button
4. Stop & Go control button
5. Timer control button
6. Heating level/Timer adjusting slider
7. ON/OFF button
MODEL: BI 0321 L
1. Zona Induksi 2000W
2. Zona Induksi 1500W
3. Kaca Temper
4. Panel Kontrol
Panel Kontrol
1. Tombol Zona Memasak
2. Tombol “ – “ pengatur waktu / level panas
3. Tombol Pengunci
4. Tombol Stop & Go
5. Tombol Pengatur Waktu
6. Tombol “ + “ pengatur waktu / level panas
7. Tombol ON/OFF

10
MODEL: BI 0721 L
1. Zona Induksi 2000W booster 2200W
2. Zona Induksi 2000W booster 2200W
3. Kaca Temper
4. Panel Kontrol
Panel Kontrol
1. Tombol Zona Memasak
2. Tombol “ + “ pengatur waktu / level panas
3. Tombol Pengunci
4. Tombol Stop & Go
5. Tombol Pengatur Waktu
6. Tombol “ – “ pengatur waktu / level panas
7. Tombol ON/OFF
•The image is a general overview and is not necessarily the same as the
product you receive. Features and completeness depends on the type of
products
•** only available on certain types.

11
Installation Instructions
The appliance must be installed and connected in accordance with current
regulations.
After unpacking the appliance, ensure there is no visible damage. If it has been
damaged during transit, DO NOT USE, contact where you buy immediately.
Please contact MODENA Call Center for instalation.
Selecting Installation Equipment
•Cut out the work surface according to the measurements shown in the picture.
•For the purpose of installation and use, a space minimum of 5 cm shall be
preserved around the hole.
•Be sure the thickness of the work surface is at least 30mm. Please select heat-
resistant work surface material to avoid larger deformation caused by the heat
radiation from the hotplate. As shown below:
•
Model
L (mm)
W (mm)
H (mm)
D (mm)
A (mm)
B (mm)
X (mm)
BI 1935
900
350
58
54
870+5-0
320+5-0
50 Min.
BI 1725
730
430
56
52
705+50
405+5- 0
50 Min.
BI 1325
288
520
56
52
265+5-0
495+5-0
50 min
BI 1625 F
590
520
56
52
555+5-0
495+5-0
50 min
BI 0721 L
730
430
58
54
705+5 -0
405+5 -0
50 min
BI 0321 L
288
520
56
52
265+5 -0
495+5 -0
50 min
PART 3: INSTALLATION

12
A (mm)
B (mm)
C (mm)
D
E
760 mm
50 mm minimal
20 mm minimal
Air intake
Air exit 5mm
Before Locating The Fixing Brackets
The unit should be placed on a stable, smooth surface (use the packaging). Do not
apply force onto the controls protruding from the hob.
Easy Fit Kits
There is one easy fit kits package for each hob, include fixing clips and screws (for
ceramic hob there are total 2pcs clip and 2pcs screw, for induction hob there are
total 4pcs clip and 4pcs screw). Find the easy fit kit package first.
Fix Clips to Hob:
Insert the fixing clip into fixing hole reserved on sides of housing, fix clip to housing
with screw, then insert hob into cabinet/work surface.
ATTENTION
•If the induction cooker is installed
with an oven below it, separator
panel must be placed between the
bottom of the stove and the frame
below it at a minimum distance of 10
cm.
•If the induction cooker is installed
without oven on the bottom, the
minimum distances to put the
separator panel is 15 cm.
•Electrical cable from both
equipments must be installed
separately to avoid short circuit.

13
Fix Hob to Cabinet:
Insert the hob into the cabinet/work surface as below diagrams, the mounted clips
on the sides can secure your hob sturdily.
Installing the Induction Cooker on Kitchen Set Table
To install an induction cooker on the kitchen
counter niche, follow these instructions:
The cable is directly plugged into a power supply
through a circuit breaker.
Post the seal adhesive along the sides of the
stove's bottom part to maintain humidity in the
bottom area of the induction cooker.
ATTENTION:
Do not use a power plug, if it is branched/paralleled with other appliances.

14
Place the induction cooker on the kitchen
counter niche, and use the available clamp from
the induction cooker packaging to fasten the
screws.
Make sure all parts have been installed and fastened
and plug the stove power cord into the power outlet.
Connecting the Hob to the Power Supply
The power supply should be connected in compliance with the relevant standard,
or a single-pole circuit breaker. The appliance have a large power rating and must
be connected to electricity by MODENA Technician.
The Method of Connections is Shown Below.
NOTES:
•If the cable is damaged or needs replacement, this should be done by
MODENA technician using the proper tools, so as to avoid any accidents.
•If the appliance is being connected directly to the mains supply, an
omnipolar circuit breaker must be installed with a minimum gap of 3mm
between the contacts.
•The installer must ensure that the correct electrical connection has been
made and that it complies with safety regulations.
•The cable must not be bent or compressed.
•The cable must be checked regularly and only replaced by MODENA
technician.

15
Before Using Your New Hob
•Read this guide, taking special note on the ‘Safety Warnings’ section.
•Remove any protective film that may still be on your new electric hob.
Using the Touch Controls
•The controls respond to touch, so you don’t need to apply any pressure.
•Use the ball of your finger, not its tip.
•You will hear a beep each time a touch is registered.
•Make sure the controls are always clean, dry, and that there is no object (e.g. a
utensil or a cloth) covering them. Even a thin film of water may make the
controls difficult to operate.
CAUTIONS:
•The hob must be installed by MODENA technicians. Please never conduct
the operation by yourself.
•The electric hob shall not be mounted next to to cooling equipment,
dishwashers and tumble dryers.
•The electric hob shall be installed properly to ensure better heat radiation
and enhance its reliability.
•The wall and induced heating zone above the work surface shall
withstand heat.
•To avoid any damage, the sandwich layer and adhesive must be heat
resistant.
•Do not use steam cleaners.
•This electric hob can be connected only to a supply with system
impedance no more than 0.427 ohm. In case necessary, please consult
your supply authority for system impedance information.
PART 4: HOW TO USE

16
Choosing the Right Cookware
•Only use cookware with a base suitable
for induction cooking. Look for the
induction symbol on the packaging or on
the bottom of the pan.
•You can check whether your cookware is suitable by carrying out a magnet test.
Move a magnet towards the base of the pan. If it is attracted, the pan is suitable
for induction hob.
•If you do not have a magnet:
•Put some water in the pan you want to check.
•If does not flash in the display and the water is heating, the pan is
suitable.
•Cookware made from the following materials is not suitable for an induction
hob: pure stainless steel, aluminium or copper without a magnetic base, glass,
wood, porcelain, ceramic, and earthenware.
•Induction hob are made from smooth, ceramic glass, the heat comes from a
magnetic induction coil which heats the cookware but not the cooking surface.
The heat from the cookware is transferred to the food.
•It’s important that you use only metal pans specifically designed and/or
approved for use on induction hobs. Never allow melamine or plastic containers
to come in contact with the heat zones.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the
same size as the cooking zone. If you use smaller pot efficiency could be less than
expected. Always centre your pan on the cooking zone.
Always lift pans off the electric hob–do not slide, or they may scratch the glass.

17
To Start Cooking
1. After the hob be connected to electricity and
power on.
Press and hold the ON/OFF control button for
about 3 seconds until you hear a “beep” to turn
the hob on. Now the hob enters Standby mode,
all heat setting indicators and Timer setting
indicators shows “-”.
2. Place a suitable pan on the cooking zone that you
wish to use.
Make sure the bottom of the pan and the surface
of the cooking zone are clean and dry.
3. Touch the heating zone selection control button
to select and activate the cooking zone.
4. Set heating level of cooking zone.
You can adjust heat setting by touching the slider control.
CAUTIONS:
You can use any kind of pot or pan for Ceramic Hob. Make sure that
base of your pot or pan is smooth, sits flat against the ceramic glass,
and same size as the cooking zone for better cooking performance.
NOTES:
For BI 1725, to adjust heating level, please skip step 3.

18
To Turn Hob Off
1. Adjust heat setting to 0 level, which
indicator shows “-“.
2. You can also turn the whole hob off by
touching the ON/OFF control button.
Beware Of Hot Surfaces
After turn off, the letter will show in the power setting indicator if cooking zone
is hot to touch. It will disappear when the surface has cooled down to a safe
temperature.
When in Standby mode, if the surface of cooking zone is hot to touch, the letter
“H” and “-” will show in its heat setting indicator alternately.
CAUTIONS:
•After connecting to electricity, when power on, the buzzer of hob beeps
once, all indicators lights up for 1 second then off.
•You can modify the heat setting at any time during cooking. The heating
element will turn off under power level 0, with indicator shows “-”
•The heat setting indicator of the selected zone will flash when adjusting.
After adjusting, the number in indicator will flash for 5 seconds and then
stop flash, then the setting has been confirmed.
•When the hob is in Standby mode, if there is no actions within 1 minute,
the electric hob will auto turn off, with buzzer beeps once.
NOTES:
•If there is power outage during cooking, all programmed settings will be
cancelled, you need to reset the programme again.
•The cooling fan of induction hob will remain on for about 1 minute after
the hob is turned off.

19
Using Booster Function –Induction Hob
For induction hob models which with Booster function, you can use the “Booster”
function to boost power of relevant cooking zone for a maximum power rating for
5 minutes. This function could reduce the cooking time, which convenience for
cooking when in hurry!
To use booster function when induction hob is working, follows below:
1. Turn on the hob by touch ON / OFF control button.
2. Touch the Booster function control button ,
the heating zone indicator will show b and
flashing for 5 seconds then stop flashing. Then
Booster function is activated, the power reach
Maximum strength for 5 minutes, and then
return to the pre-set heat setting.
3. To turn off Booster function:
•When in Booster function, touch the “Booster” control button again, you
can deactivate Booster fuction.
•You can also cancel Booster function by adjusting power level setting.
Child Lock
•You can lock the controls to prevent unintended use (for example children
accidentally turning the cooking zones on) by activate Child Lock function.
•When the controls are locked, all other touch control buttons will be disabled
except the ON/OFF control button and Child Lock control button.
NOTES:
This can also be used as an energy saving function: if you want to heat further
pans, use the hotplate that is still hot.
NOTES:
After booster finish, the cooking zone will return to previously power level
setting before booster.

20
To lock the controls
Touch the Child Lock control button once . The timer indicator will show “Lo“,
and Child Lock function is activated.
To unlock the controls
1. Make sure the electric hob is turned on.
2. Touch and hold the Child Lock control button for 3 seconds, the buzzer
beeps once and “Lo” disappears in timer indicator, the Child Lock is deactivated.
You can now start using your electric hob.
Stop & Go Function
•Make cooking easy! When cooking, your doorbell rings, phone rings, or kid
shouts from another door. Need to step out of kitchen? These means dinner
could burn, or take longer time to ready if you switch everything off.
•The Stop & Go function can turn off all zones. When you back, with touching of
the button once more , hob restarts where they were, to continue cooking.
Activate Stop & Go function
To activate Stop & Go function, you can press the Stop & Go function button once.
Then all programmed setting be hold on and hob stop heating, all heat setting
indicators show “P”.
NOTES:
Under Child Lock function, if you turn the hob off, the Child Lock function will
still be activated. If you want to turn on the hob after that, you need to
deactivate Child Lock function first.
WARNING:
Under the child lock mode, all controls button are disabled except the
ON/OFF and child lock . You can always turn the hob off with the
ON/OFF control in an emergency, but you shall unlock the hob first in the
next operation