Modena BK 1725 C Owner's manual

User
Manual Book
Built-In Electric Hob Manual
BK 1725 C
BI 0721 C

1
TABLE OF CONTENT
Part 1: Safety & Warnings 2
Part 2: Installation 6
Part 3: Operation Instructions 12
Part 4: Cleaning & Maintenance 28

2
Safety Warnings
Your safety is important to us. Please read below information
carefully before installing or using your Hob.
Installation
Electrical Shock Hazard
• Disconnect the appliance from the mains electricity supply
before carrying out any work or maintenance on it.
• Connection to a good earth wiring system is essential and
mandatory.
• Alterations to the domestic wiring system must only be made by
a qualified electrician.
• Failure to follow this advice may result in electrical shock or
death.
Cut Hazard
• Take care - panel edges are sharp.
• Failure to use caution could result in injury or cuts.
Important safety instructions.
• Read these instructions carefully before installing or using this
appliance.
• No combustible material or products should be placed on this
appliance at any time.
• Please make this information available to the person
responsible for installing the hob as it could reduce your
installation costs.
PART 1 : SAFETY & WARNING

3
• In order to avoid a hazard, this appliance must be installed
according to these instructions for installation.
• This appliance is to be properly installed and earthed only by a
suitably qualified person.
• This appliance should be connected to a circuit which
incorporates an isolating switch providing full disconnection
from the power supply.
• Failure to install the appliance correctly could invalidate any
warranty or liability claims.
Operation and Maintenance
Electrical Shock Hazard
• Do not cook on a broken or cracked hob. If the hob surface
should break or crack, switch the appliance off immediately at
the mains power supply (wall switch) and contact a qualified
technician.
• Switch the hob off at the wall before cleaning or maintenance.
• Failure to follow this advice may result in electrical shock or
death.
Health Hazard
• This appliance complies with electromagnetic safety standards.
• However, persons with cardiac pacemakers or other electrical
implants (such as insulin pumps) must consult with their doctor
or implant manufacturer before using this appliance to make
sure that their implants will not be affected by the
electromagnetic field.
• Failure to follow this advice may result in death.
Hot Surface Hazard
• During use, accessible parts of this appliance will become hot
enough to cause burns.

4
• Do not let your body, clothing or any item other than suitable
cookware contact the ceramic glass until the surface is cool.
• Keep children away.
• Handles of saucepans may be hot to touch. Check saucepan
handles do not overhang other cooking zones that are on. Keep
handles out of reach of children.
• Failure to follow this advice could result in burns and scalds.
Cut Hazard
• The razor-sharp blade of a hob scraper is exposed when the
safety cover is retracted. Use with extreme care and always
store safely and out of reach of children.
• Failure to use caution could result in injury or cuts.
Important safety instructions
• Never leave the appliance unattended when in use. Boil over causes
smoking and greasy spillovers that may ignite.
• Never use your appliance as a work or storage surface.
• Never leave any objects or utensils on the appliance.
• Do not place or leave any magnetizable objects (e.g., credit cards,
memory cards) or electronic devices (e.g., computers, MP3 players)
near the appliance, as they may be affected by its electromagnetic field.
• Never use your appliance for warming or heating the room.
BEWARE!
Metallic objects such as knives, forks, spoons and lids should not
be placed on the hob surface since they can get hot.

5
• After use, always turn off the cooking zones and the hob as described
in this manual. Do not rely on the pan detection feature to turn off the
cooking zones when you remove the pans.
• Do not allow children to play with the appliance or sit, stand, or climb
on it.
• Do not store items of interest to children in cabinets above the hob.
Children climbing on the hob could be seriously injured.
• Do not leave children alone or unattended in the area where the
appliance is in use.
• Children or persons with a disability which limits their ability to use
the appliance should have a responsible and competent person to
instruct them in its use. The instructor should be satisfied that they can
use the appliance without danger to themselves or their surroundings.
• Do not repair or replace any part of the appliance unless specifically
recommended in the manual. All other servicing should be done by a
qualified technician.
• Do not use steam cleaner to clean hob.
• Do not place or drop heavy objects on hob.
• Do not stand on your hob.
• Do not use pans with jagged edges or drag pans across the ceramic
glass surface as this can scratch the glass.
• Do not use scourers or any other harsh abrasive cleaning agents to
clean your hob, as these can scratch the ceramic glass.
• If the power supply cable is damaged, it must only be replaced by
qualified technician.
•This appliance is intended to be used in household and similar
applications such as: -staff kitchen areas in shops, offices and other

6
working environments; -farm houses; -by clients in hotels, motels and
other residential type environments; -bed and breakfast type
environments.
• This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
• WARNING:
Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire. NEVER try to extinguish a fire with
water, but switch off the appliance and then cover flame e.g., with a lid
or a fire blanket.
Installation Guide
The appliance must be installed and connected in accordance
with current regulations.
After unpacking the appliance, ensure there is no visible damage.
If it has been damaged during transit, DO NOT USE, contact
where you buy immediately.
Selection of installation equipment
• Cut out the work surface according to the sizes shown
in the drawing.
• For the purpose of installation and use, a minimum of 5 cm
space shall be preserved around the hole.
PART 2 : INSTALLATION

7
• Be sure the thickness of the work surface is at least 30mm.
Please select heat-resistant work surface material to avoid
larger deformation caused by the heat radiation from the
hotplate. As shown below:
Under any circumstances, make sure the electric hob is well ventilated and the air inlet
and outlet are not blocked. Ensure the electric hob is in good work state. As shown
below:
Note: The safety distance between the hotplate and the cupboard
above the hotplate should be at least 760mm.
Model
L(mm
)
W(mm
)
H(mm
)
D(mm
)
A(mm
)
B(mm
)
X(mm
)
BI 0721 C
BK 1725 C
730
430
58
54
705+5
-0
405+5
-0
50 mini

8
A(mm)
B(mm)
C(mm)
D
E
760mm
50mm minimal
20mm minimal
Air intake
Air exit 5mm
Installing the foam gasket
Before inserting the hob into the opening in the kitchen
worktop, the supplied foam gasket (in a plastic bag) must be
attached to the lower side of the ceramic glass.
Do not install the hob without the foam gasket!
The gasket should be attached to the hob in the following
method:
• Remove the protective film from the gasket.
• Then attach the gasket to the lower side of the glass, next to
the edge.
• The gasket must be attached along the entire length of the
glass edge and should not overlap at the corners.
• When installing the gasket, make sure that the glass does not
come into contact with any sharp objects.

9
Before locating the fixing brackets
The unit should be placed on a stable, smooth surface (use the
packaging). Do not apply force onto the controls protruding
from the hob.
Easy Fit kits
There is one easy fit kits package for each hob, include 2pcs
fixing clip and 2pcs screw. Find the easy fit kit package first.
Fix clips to hob:
Insert the fixing clip into fixing hole reserved on
sides of housing, fix clip to housing with screw, then insert hob
into cabinet/work surface.
Fix hob to cabinet:
Insert the hob into the cabinet/work surface
as below diagrams, the mounted clips on the sides can secure
your hob sturdily.

10
Connecting the hob to the mains power supply
The power supply should be connected in compliance with the relevant
standard, or a single-pole circuit breaker.
The appliance has a large
power rating and must be connected to electricity by a Qualified
Electrician
.
NOTES!
1. If the cable is damaged or needs replacing, this should be done by an
after-sales technician using the proper tools, so as to avoid any
accidents.
2. If the appliance is being connected directly to the mains supply, an
omni polar circuit breaker must be installed with a minimum gap of 3mm
between the contacts.
3. The installer must ensure that the correct electrical connection has
been made and that it complies with safety regulations.
4. The cable must not be bent or compressed.
5. The cable must be checked regularly and only replaced by qualified
technician.
The method of connections shown below:

11
Cautions
1. The hob must be installed by qualified personnel or technicians.
Please never conduct the operation by yourself.
2. The electric hob shall not be mounted to cooling equipment,
dishwashers and rotary dryers.
3. The electric hob shall be installed such that better heat radiation can
be ensured to enhance its reliability.
4. The wall and induced heating zone above the work surface shall
withstand heat.
5. To avoid any damage, the sandwich layer and adhesive must be heat
resistant.
6. A steam cleaner is not to be used.
7. This electric hob can be connected only to a supply with system
impedance no more than 0.427 ohm. In case necessary, please consult
your supply authority for system impedance information.
NOTES!
For some of the models, there might applied with a power cord with
plug. If so, you can directly plug in socket. Please keep power cord plug
out after use, for those model power cord with plug.

12
OPERATION INSTRUCTIONS
Product Overview
Model: BI 0721 C
Control Panel
PART 3 : OPERATION INSTRUCTIONS
1. 2000W booster 2200W induction Zone
2. 2000W booster 2200W induction Zone
3. Ceramic Glass
4. Control panel of cooking zone#1
5. Control panel of cooking zone#2
1
3
2
4
5
2
6
4
5
3
1. Booster function control button
2. Stop & Go control button
3. Timer control button
4. Heating level/Timer adjusting
slider
5. Child Lock control button
6. ON/OFF button
4. Heating level/Timer adjusting slider
5. Child Lock control button
6. ON/OFF button

13
Model: BK 1725C
4. Heating level/Timer adjusting slider
5. Child Lock control button
6. ON/OFF button
NOTE!
Product diagrams in instruction manual for reference only, there
might be slightly difference due to continually product
improvements.
1. 2000W booster 2200W induction Zone
2. 2200/1000W Ceramic Dual Zone
3. Ceramic Glass
4. Control panel of cooking zone#1
5. Control panel of cooking zone#2
1
3
2
4
5
1. Booster / Extend zone control button
2. Stop & Go control button
3. Timer control button
4
5
3
2
4
5
3
6

14
Before using your New Hob
• Read this guide, taking special note of the ‘Safety Warnings’ section.
• Remove any protective film that may still be on your new electric hob.
Using the Touch Controls
• The controls respond to touch, so you don’t need to apply any
pressure.
• Use the ball of your finger, not its tip.
• You will hear a beep each time a touch is registered.
• Make sure the controls are always clean, dry, and that there is no
object (e.g., a utensil or a cloth) covering them. Even a thin film of water
may make the controls difficult to operate.
Choose the right Cookware
• Only use cookware with a base suitable for induction
cooking. Look for the induction symbol on the packaging or on
the bottom of the pan.
• You can check whether your cookware is suitable by
carrying out a magnet test. Move a magnet towards

15
• You can check whether your cookware is suitable by carrying out
a magnet test. Move a magnet towards the base of the pan. If it is
attracted, the pan is suitable for induction hob.
• If you do not have a magnet:
1. Put some water in the pan you want to check.
2. If does not flash in the display and water is heating, the
pan is suitable.
• Cookware made from the following materials is not suitable for an
induction hob: pure stainless steel, aluminum or copper without a
magnetic base, glass, wood, porcelain, ceramic, and earthenware
• Induction hob are made from smooth, ceramic glass, the heat
comes from a magnetic induction coil which heats the cookware
but not the cooking surface. The heat from the cookware is
transferred to the food.
• It’s important that you use only metal pans specifically designed
and/or approved for use on induction hobs. Never allow melamine
or plastic containers to come in contact with the heat zones.
• A pan which diameter less than 140mm may not be detected by
the induction hob.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the
glass, and is the same size as the cooking zone. If you use smaller pot
efficiency could be less than expected. Always center your pan on the
cooking zone.

16
Always lift pans off the electric hob – do not slide, or they may scratch
the glass.
NOTES!
You can use any kind of pot or pan for Ceramic Hob.
Using your Hob
To start cooking
1. After the hob be connected to electricity and power on.
Press and hold the ON/OFF control button for
about 3 seconds till you hear a “beep” to turn
the hob on.
Now the hob enters into Standby mode,
all heat setting indicators and Timer setting indicators
shows “-”
2. Place a suitable pan on the cooking zone that you wish to
use.

17
• Make sure the bottom of the pan and the surface
of the cooking zone are clean and dry.
3. Set heating level of cooking zone
• You can adjust heat setting by touching the slider control.
NOTES!
1. After connect to electricity, when power on, the buzzer of hob beeps
once, all indicators light up for 1 second then go out.
2. When the hob in Standby mode, if there is no practice within 1 minute,
the electric hob will auto turn off, with buzzer beeps once.
3. To turn on hob, press the ON/OFF control button and hold on for
about 3 seconds; To turn it off, just need to press ON/OFF button
again.
4. The power level can be adjusted from 0 to 9, default setting is level
5.
5. The heat setting indicator of the selected zone will flash when
adjusting.
After adjusting, the number in indicator will flash for 5 seconds and
then stop flash, then the setting be confirmed.
To turn off hob
1. You can turn the cooking zone off by adjust heat setting to
level 0, which indicator shows “- “.
2. You can also turn the hob off by touching the ON/OFF
control button.

18
NOTES!
If power cut off during cooking, all setting will be cancelled.
The cooling fan will remain on for about 1 minute after turned off.
Using Large Heating Area-Ceramic Hob
Some of ceramic hob models might have one or several extended
cooking zones (Oval/Dual/Triple zone), these extended zones can
provide larger cooking area and additional heat to fit for different size
of cooking pan.
To use Extended zone when hob is working, follows below:
1. Select and active the cooking zone which you would like to use
extended zones, for those cooking zone with this feature.
1) For model BK 1725 C:
Touch the slider control button of corresponding heating zone
to active it for adjustment.
2. The central zone will be switched on, when first adjust of heat
level for extended cooking zone.
3. When the heating zone be selected and active (power level
indicator flashing), touch extended zone control button
to active extended heating element to get a large heating area.

19
NOTES!
1. By continuous touch the control button, the extended zones work at
below consequence: Dual zone: “Central-Dual-Central-Dual-Central-Zone”
2. When Dual Zone active, the heat level LED indicator of it will show
heat setting and “ “ alternately.
Using Booster Function-Induction Hob
Some of induction hob models might have one or several cooking zones
which has Booster function. You can use the “Booster” function to boost
power of relevant cooking zone for a maximum power rating for 5
minutes. This function could reduce the cooking time, which
convenience for cooking when in hurry!
To use booster function when induction hob is working:
1. Select and active the cooking zone which you would like to use
extended zones, for those cooking zone with this feature.
Touch the slider control button of corresponding heating zone to
active it for adjustment.
2. When the heating zone be selected and active (power level
indicator flashing), touch the corresponding Booster function
control button , the heating zone indicator will show “b”
and flashing for 5 seconds then stop flashing, then Booster
function be active.