Modena FC 8640 WGR Owner's manual

User
Manual Book
Freestanding Cooker
FC 8640 WGR
FC 8640 WER
FC 8640 IER
FC 8540 WER
FC 8540 WGR

2
TABLE OF CONTENT
SAFETY & WARNING 3
FEATURES 6
Control Knobs 6
INSTALLATION 9
Placement of the Oven 9
Installation of the Gas Pipe 9
Placing Distances of Appliance 10
Nozzle Replacement 11
Transportation 11
HOW TO USE 13
Arrange of the Feet 13
Electrical Connection 14
Use of the Gas Cooker and Firing 15
Electric Cooker Control Button Degrees 16
Use of Upper and Lower Parts of Oven 16
MAINTENANCE 18
Maintenance and Cleaning 18
Cleaning of the Upper Parts and Cookers 18
Cleaning the Inside of the Oven 19
Replacement of the Oven’s Lamp 19
TROUBLESHOOTING 21
Authorized Service Centre Call Check 21
SPECIFICATIONS 22
This guidebook explains everything you need to know about your new
product. Please contact our Customer Care should you need further
assistance through www.modena.com.

3
READ THE INSTRUCTIONS AND SAFETY WARNINGS BEFORE YOU USE
THE FREESTANDING COOKER.
This product is designed for home use!
•To be able to use your oven, please call the closest authorized
service. The oven is adapted to the LPG. To use with the natural
gas please call and apply to the authorized service.
•To prepare the oven for use, prepare the montage place and
electric grounds first and then call the authorized service.
•The power supply should be 230 Volt / 50 Hz.
•In case the fuse of your house is lower than 16 Amp., call an
electrician to install a 16 Amp. fuse.
•The appliance must be grounded. Our company will have no
responsibility for any inconvenience if it is used without
grounding.
•Do not montage the oven in a way that the electricity cord does
not touch the heated surfaces. Otherwise, the cord insulation
may be damaged.
•If you need to replace the power cord, contact an authorized
service.
•Our company will have no responsibility if the oven is used with
different purposes other than described in this manual.
•Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the oven door glass since they can scratch the surface,
which may result in shattering of the glass.
•Before replacing oven lamp, please disconnect the cooker from
power supply for your safety.
SAFETY & WARNING
NOTE!
Unpack the package before you use the product. Please do not
forget to detach the cartoons and polystyrene on front glass,
plate and grill. The package material may be harmful for
children.

4
•While you use the oven part of the product, do not touch the
inner cavity and heating element.
•Do not put flammable materials into the oven. In case the oven
is on without purpose, they may be burned.
•Use the oven mitt to remove hot dishes.
•Wipe of hot steams from the glass door with a cloth.
•Oils can be flamed while you are cooking. Therefore, please pay
attention to curtains and clothes.
•The cooking area becomes warm and humid.
•Please be sure about the ventilation of your kitchen.
•With prolonged use of the cooker, more frequent ventilation may
be needed.
•If your product has a timer, set the timer right before the first use
and after every power cut. Otherwise the oven part will not
operate.
•Be sure that all burners are switched off before you close the
glass lid cover (if the oven has glass cover). Otherwise, the glass
may break.
•Keep children away from the product.
•Do not let children to sit or step on the front cover while it is
open.
•Metallic objects such as knives, forks, spoons and lids should not
be placed on the hob surface since they can get hot.
•The door or the outer surface may get hot when the appliance is
operating.
•Make sure that, the main voltage is identical to the information
as given on the rating label.
•Place the appliance on a fully horizontal surface and away from
inflammable parts.
•The appliances should be positioned so that the plug is always
accessible.
•Do not pass the electric cables behind or near to the heating
parts of the appliance and through the holes or covers that may
WARNING!

5
cut or damage the wires.
•If the supply cord is damaged, it must be replaced by the
manufacturer or authorized service center.
WARNING!
Accessible parts may be hot when the grill in use. Children
should be kept away.

6
A. Upper oven control knob
B. Cooker control knob
C. Bottom oven control knob
D. Upper oven warning lamp
E. Bottom oven warning lamp
1. Small burner
2. Middle burner
3. Big burner
4. Control panel
5. Oven glass
Control Knobs
FC 8640 WER, FC 8640 IER, FC 8540 WER
FEATURES

7
1. Small burner knob
2. Medium burner knob
3. Medium burner knob
4. Big burner knob
5. Oven/ grill knob
6. Small burner
7. Medium burner
8. Big burner
9. Glass door
Control Knobs
FC 8640 WGR

8
Using The Grill Function
If your cooker has grill function:
•Press the Grill button.
•When using a rotisserie, it is recommended to install tray for
grilling. This will prevent splashing or dripping oil in order to keep
the cavity clean.
•If you are using a spit> place the drip tray on the lower oil
collection racks. Pour some water into it for easier cleaning.
•Leave the lid half open> while the oven is heating up for 5-10
minutes.
•Lubricate the skewer with oil> to prevent food sticking to it.
•When using the grill, leave the door half open after the oven has
warmed up.
ATTENTION!
When using the grill function, place a shield between the front
cover and the cooker body, for the handles on the control panel
do not get hot. The supplier is not liable for damage caused by
not using the cover.

9
Placement of the Oven
The product is arranged for the LPG. Use the product with a 300 mmSS
pressure expansion valve that is approved by TSE. Replace the
expansion valve and its pipe periodically.
Installation of the Gas Pipe
According to the location of the tube, choose the suitable location for
the pipe connection (see figure below). Place the clamp on the tube.
Soak one end of the tube in hot water for one minute to soften the
material and push it onto the fitting on the plate. Tighten the clamp with
a screwdriver. Do the same with the other end of the tube> connected
to the pipeline. Before turning on the stove, it is necessary to check the
connections for gas leaks.
Connect the product to a pipeline or tap on the natural gas supply line
with a short pipe. Its length should not exceed 125 cm.
INSTALLATION

10
Placing Distances of Appliance
The product should be at the same level with the kitchen top. You may
arrange the level by using the oven’s feet. There should be 50 mm
distance between the wall and upper parts of the oven and this place
should be resistant to the heat. There should be 750 mm distance over
the upper cooker of the product.
NOTE!
The natural gas valve should be reached easily!
ATTENTION!
LEAKAGE CONTROL
•Do not use lighter or match to check the leakage.
•Make sure that the buttons are switched off and the tube
should be open. Use soap bubble to check the leakage on
both side of the pipe. There are bubbles in case there is
any leakage. If there is any leakage, check the
connections again.

11
Nozzle Replacement
Hob Burner Nozzle Replacement
•Remove the pan supports.
•Remove cooker lid and baffles.
•Using a socket wrench 7, unscrew and remove the nozzles
replacing them with the required ones.
Transportation
In Case You Need to Transport
•Keep the original packing. Transport the product with its original
package. Follow the transportation regulations that are indicated
on the package.
•The gas equipment of the cooker must be guarded. Use a
cardboard to put between the lid and cooker area and secure
NOTES!
Transformation made from LPG to natural gas must be done in
factory. Screw must be completely tightened to the right side when
transformation made from natural gas to LPG.

12
them at the sides.
•Attach a cardboard with a diameter of 1 or 1.5 cm to the oven lid
to protect it from damage caused by the destruction of baking
sheet and wire rack during transportation.
If there is no Original Packing
•Take the necessary measures to protect external surfaces and
glass from possible damage. Transport the oven
perpendicularly and do not put anything else on it

13
Arrange of the Feet
Use the plastic feet to arrange the balance and height of the oven. Four
feet of the oven are adjustable.
You may arrange the level by turning the feet to right or left after you lift
the oven. We suggest you adjust only the front feet to be practical.
The gas pipe and electric cord should be away from the hot places of
the oven. Do not move the oven more than what the tube pipe let in case
there is a gas pipe. Since there can be a leakage if you push/pull harder.
HOW TO USE

14
Operating Cooker
The control knobs should be turned anticlockwise until the small flame
symbol appears, and vice versa for the larger symbol.
. No gas supplies
Maximum gas supply
Minimum gas supply
Electrical Connection
FC 8640 WER, FC 8640 IER, FC 8540 WER
The unit is pre-set to work with voltage of single phase 230 V. Before
making the connection makes sure that:
•The energy power available in the user’s house is suitable for the
normal supply of this appliance (see rating label).
•The appliance is supplied without a plug. Therefore, you have to
install a plug that matches a value indicated in the rating label.
The plug must be connected into an outlet. If you want to
connect to the network, you must connect the multi-pole
network in accordance with the regulations in force. The brown
live wire (coming from the junction box terminal of the cooker)
must always be connected to the phase of the power supply.
The power cord must be routed in such a way that it does not at

15
any point reach 50ºC above room temperature.
•The electrical installation of the oven should be made according
to the local and national regulations.
•The appliance should be positioned so that the plug and socket
is always accessible.
•If you do not have a grounded socket; then have it done by an
authorized electrician.
•Do not locate the power cable of your product close to the hot
parts of the product.
•Pay maximum attention in order to not have it damaged.
•Place your oven in a location where the power cable reaches the
socket.
•Do not use extra connection cable.
Use of the Gas Cooker and Firing
Manual Ignition of Gas Oven
There is a special safety mechanism on the gas stove. To apply gas to
the stove and ignite it, you turn the buttons counter - clockwise while
pressing it down. In such a situation, light the oven or grill with a gas
lighter. If the operation does not work, leave the gas lighter and repeat
the procedure again. If it doesn't work, wait a minute and try again. Do
not assume that the oven door may be warm under a working oven, Keep
children away from the oven.
. No gas supplies
Maxımum gas supply
Minimum gas supply
ATTENTION!
Do not push the button more than 15 seconds.

16
Electric Cooker Control Button Degrees
1st DEGREE
2nd DEGREE
3rd DEGREE
250 W
750 W
1000 W
Standby on lower degrees
Cook on normal degrees
Frying
Use of Upper and Lower Parts of Oven
Control Buttons of Upper and Lower Heaters
The button controls the thermostat, which regulates the heat of the
oven. When the oven is on, thermostat lamp is turned on at the same
time as the oven resistance. When the internal temperature of the oven
reaches the value you set, the thermostat stops the circuit and the
button switches off. When the temperature is lower than you selected,
the thermostat turns on again and the lamp is lit. This ensures the
desired warmth during cooking.
Use of Upper and Lower Oven
•Before cooking, pre-heat the oven with closed lid. After
preheating, place the dish into the oven.
•When finished cooking, turn the heater command to “O” to stop
the oven.
•Because of the insulation materials and heaters, you will smell
something when you first enter the oven. To get rid of the smell,
place the empty oven for 45 minutes on MAX heat.

17
•If you are using a baking sheet other than the original one, select
the cooking conditions according to your own experience.
•Do not use glass pans or other heat-reflecting objects to prepare
dough. A baking sheet for the oven is the most suitable one.
•Align the trays while you are putting them into the oven.
•Use the dariole to make a cake for desired result.
•Cooking duration may vary according to the quantity.
•You can stop the system five minutes earlier to save energy
without opening the cover.
NOTES!
The values on cooking tables were laboratory results. The cooking
duration may change according to the quantity. You can create
delicious results in accordance with your habits.

18
Maintenance and Cleaning
•Unplug the power cord before you clean.
•Pay attention to the cleaning agents that may contains materials
that can scratch the surface of the oven. Use liquid or other
cleanser that will not damage the product.
•If the boiled liquids are burned, they can damage the cooker, so
rinse them as they boil away.
•Be careful, abrasive and liquid cleansers can erase the signs on
the control board. Do not use steel wool.
•Do not use the materials including any kind of acid.
Cleaning of the Upper Parts and Cookers
•Remove the pan support and the lid on the upper part of the
product.
•Clean the cooker area with a soap cloth. Use the same for the
pan support and cooker lid. After it dry, place the pan support
and lid back to their place. Do not clean the cooker area with
steel wool, it may scratch the surface.
•The fire causes some changes on tips of the carrier. It does not
affect the operation of the cookers in anyway.
MAINTENANCE
NOTES!
Do not wash the materials in dishwasher. Use the metal cleaners in
accordance with the instruction on them to clean the pan support
and lid in case the soap water does not work.

19
Cleaning the Inside of the Oven
•Before cleaning, unplug the power cord.
•Remove the trays and grill, clean the inside cavity with a soap
cloth. Then, clean with a wet clothe. Do not clean with dry and
powder cleanser.
•DO NOT clean the inside of the oven with harsh materials like
steel wool. Use the special cleanser in accordance with their
instructions.
Replacement of the Oven’s Lamp
•Disconnect the electricity.
•Remove the lamp protector and turn it towards left side.
•Then remove the lamp by turning it towards left.
•After you replace the lamp from the authorized service center,
you can install the protector again.
NOTES!
Do not use harsh materials to clean and use special agents to clean
the glasses.

20
Pursuant to Directives 2002/95/EC, 2002/96/EC and
2003/108/EC relating to the reduction of the use of hazardous
substances in electrical and electronic appliances, as well as
to the disposal of refuse, the crossed out bin symbol on the
appliance indicates that the product, at the end of its useful
life, must be collected separately from other refuse.
Therefore, the user must consign the product that has reached the end
of its working life to the appropriate selective collection center for
electrical and electronic refuse, or deliver it back to the retailer when
purchasing an equivalent product, on a one for one basis. Adequate
selective collection forth e subsequent forwarding of the
decommissioned product to recycling, treatment and ecologically
compatible disposal contributes to avoiding possible negative effects on
the environment and on health and promotes the recycling of the
materials of which the appliance consists. The illicit disposal of the
product by the user results in the application of administrative sanctions.