Modena BH 6725 LF Owner's manual

Nomor : IMKG.2045.08.2022
User
Manual Book
Built in Gas Hob
BH 6725 LF
BH 2933 LL
BH 1945
BH 6935 LF
BH 2723 LL
BH 1725 LG
BH 4934
BH 2933 LJ
BH 5725 LK
BH 4724
BH 2723 LJ
BH 5725 LO
BH 2937
BH 7723 LLD
BH 1728
BH 2727
BH 1935 LA
BH 1728 LA
BH 4937
BH 1935 LB
BH 1728 LB
BH 4727
BH 1725 LA
BH 1725 LAT
BH 2934
BH 1725 LB
BH 1725 LBT
BH 2724
BH 1725 LA MASSA
BH 1725 MIMA
BH 0935
BH 1945
BH 1725 LG
BH 0725
BH 1935
BH 5725 BABK
BH 0325
BH 1735
BH 5725 AABK
BH 1325 ABBK
BH 1725
BH 1725 ABBK
BH 1725 W
BH 1935 ABBK
BH 1645
BH 1325 ACBK
BH 1325
BH 1725 ACBK
BH 1315

2
TABLE OF CONTENTS
Part 1: Safety Warnings 3
Part 2: Name of Parts 4
Part 3: Installation 5
Adjusting the Stove to the Kitchen Table 5
Installing the Stove to the Kitchen Table Hole 7
Part 4: How to Use 9
Control Knob 9
Lighting The Burner 9
Other BH Series 10
Touch Control BH 7723 LLD 12
BH 1725 LAT & BH 1725 LBT 14
Part 5: Maintenance 16
Part 6: Troubleshooting 17
Part 7: Precaution 18
Part 8: Specification 19
This guide book explains everything you need to know about your new
product. Please contact our Customer Care should you need further
assistance through www.modena.com

3
If you do Not understand about the procedure installation of gas cooker,
you should contact MODENA Service Center to perform the installation.
Prepare the support equipment required for installation like:
•LPG gas cylinder.
•Gas hose with a safety standard for lack.
•Clamp.
•Gas regulator clamp / hose clamp with a lowpressure type.
•Matches / gas lighter.
Room air ventilation
The air in the room that will be put gas appliances must have good
ventilation so that air can flow / move smoothly (there is circulation), if
the air in the room can Not flow then the air in the room will contain more
combustion of the gas compared to oxygen. It will cause the flame on
the stove / burner is Not perfect (a yellow flame because lack of oxygen).
Therefore, the room that will be put gas appliances should have good
ventilation.
PART 1: SAFETY WARNINGS

4
BH Series
1. Upper Plate
2. Grid
3. Control Knob
4. Lighter Plugs
5. Gas Safety Sensor
6. Small Fire Pit
7. Large Fire Pit
8. Bottom Plate
9. Burner
BH 7723 LLD
1. Grid
2. Burner
3. Control Panel
4. Tempered glass
•Image is a general overview and is not necessarily the same as the
product you receive.
•The features and product specifications depend on the product type
PART 2: NAME OF PARTS

5
Adjusting the Stove on Kitchen Table
•Stove can be installed on the kitchen table as long as the table is
resistant to heat. To make a hole at the kitchen table use cardboard
templates to customize the size. Make a hole should be proportional
not too wide or too small.
•To ensure the final result in accordance with the installation plan,
before making the planting hole check the distance between the
bottom plate to the top plate.
•Check if the size of the hole on the kitchen table is appropriate to put
the stove.
•If the stove with a top plate of glass will be installed parallel to the
tile, to install make a distance of at least 2 mm for expansion.
•Free area under the stove must be more than 40 cm, and the distance
to objects on the stove should be more than 100 cm.
•It is recommended to use a cabinet / counter with a width of more
than 55 cm, make a hole at the front of the open air circulation
cabinets / counter.
•The size of the hole to put the stove on the kitchen table is as follows.
PART 3: INSTALLATION

6
Type
A (mm)
B (mm)
Type
A (mm)
B (mm)
BH 5725 LK
BH 5725 LO
635
350
BH 0325
BH 1315
BH 1325
BH 1325 ABBK
BH 1325 ACBK
268
480
BH 2723 LL
722
428
BH 7723 LLD
703
403
BH 6935 LF
820
475
BH 1725 LG
670
370
BH 6725 LF
685
400
BH 0725
BH 1725
BH 1725 W
BH 1725 LA
BH 1725 LB
BH 1725 LA MASSA
BH 2724
BH 2725
BH 4724
BH 1735
BH 4727
BH 2727
BH 1728
BH 1728 LA
BH 1728 LB
BH 1725 LAT
BH 1725 LBT
BH 1725 MIMA
BH 2723 LJ
BH 1725 ABBK
BH 1725 ACK
660
360
BH 0935
BH 1935
BH 1935 LA
BH 1935 LB
BH 2935
BH 4934
BH 1945
BH 1945 LA
BH 2934
BH 2933 LL
BH 2933 LJ
BH 1945
BH 1945 LA
BH 2934
BH 2933 LL
BH 2933 LJ
BH 2937
BH 4937
BH 1935 ABBK
827
552
470
472
BH 1645
552
472
BH 5725 AABK
BH 5725 BABK
650
350

7
Installing The Stove On The Kitchen Table Hole
To install the stove in your kitchen table hole, do the followings:
•Connect the hose that connecting the
gas pipe, and tighten using a wrench
•Before installing the pipe that
connecting the gas hose, check and
make sure whether the gasket / seal (A)
has already installed.
•Perform installation properly Elbow,
where the main pipe with Elbow should
us e a seal, to avoid gas leakage.
•Use of two pass key 22 & 24 (adjusted)
at the time of going to Elbow perform
installation, test connections with
soapy water, make sure there are no
leaks.
•Installation should be performed by
experienced technicians, all forms of
loss and adverse effects due to
improper installation or MODENA
technician, then it is not be the
responsibility of MODENA.
ATTENTION!
If the stove is installed with oven under
heat, separator panel must be placed
under the stove and frame underneath
with a minimum distance of 10 cm.
NOTE
For the size of the hole a few other models that are Not contained
In the above illustration can be seen in the table of specifications or
can be consulted to MODENA Service Center

8
•Embed Seal Adhesive (glue) along the
bottom edge of the stove. It is
necessary to keep the moisture on the
bottom of the stove.
•Connect the gas hose to the stove, and
tighten the connection with the hose
clam p. Then do leak test on the gas
hose connection with your stove.
•Put the stove on the kitchen table hole,
then to tighten use a hook which has
been available on stove packaged
equipment.
•Install the Burner set on its position
•Install the regulator on gas tube and stove is already use
CATATAN
For some products with certain models does not include clip (hook)
ATTENTION:
• To avoid gas leakage, please use gas standard hose with gas
safety device.
• Use the hose and regulator are perfect to avoid gas leaks can
cause explosions.
• Do not use a high pressure regulator.

9
Control Knob
The amount of gas flow in the furnace / burner can be set on the knob
as shown in the figure below:
Lighting The Burner
To ignite the flame easily, light the burner before placing the cooking
utensil on the pan support.
For the model with electric ignition switch united with the knob.
To turn on the burner, push the knob and then turn to counterclockwise
until the maximum fire symbol. By pressing the knob, it ignites
automatically.
For the model using safety valve:
some of built-in gas-cooker models are included with safety valve that
functioned to automatically cut off the gas flow if the burner doesn’t turn
on. To turn on the burner, turn the knob to the maximum gas, then push
for 3-5 second. Released the knob if the fire has turned on and adjusts
the fire by turning the knob to the desired position.
At the first time there are times when the cigarette lighter does not run
smoothly, do the lighter several times. If the process fails or long lighters
could be because the battery has run out / damaged.
PART 4: HOW TO USE

10
For model without electric ignition :
To light the burner with the condition doesn’t have electric power, turn
on the fire using matches and approach the fire to the upper side of
burner than push the knob and turn counter clockwise until the maximum
fire symbol condition.
1. To decrease / increase the fire on turned on burner :
Turn the knob to position the maximum fire sign or direction of the
position of the minimum fire sign.
2. To use the minimum fire:
3. Turn the knob to gas flow –Minimum .
4. To turn off the fire on burner : Turn the knob to “OFF” symbols.
Other BH Series
Control Knob
The symbols on the control knobs mean the following:
•No gas flow / OFF
Maximum gas flow
Minimum gas flow
Automatic Ignition
ATTENTION
In the event of a gas leak, do not turn on electronic equipment, turn
on the fan or testing by fire. Close the gas valve as soon as possible
and open the whole window / vent.

11
Lighting the Burner
To acquire the flame easily, light the burner before placing the cooking
utensil on the pan support.
For the model with electric ignition switch united with the knob.
This model as sign with symbol beside of symbol (maximum gas
stream). To turn on the burner, push the knob and then turn to counter
clockwise until the maximum fire symbol. By pressing the knob,
automatically its turn on the ignition.
For the model using safety valve :
Some of built-in gas-cooker models are included with safety valve that
functioned to automatically cut off the gas flow if the burner doesn’t turn
on. To turn on the burner, turn the knob to the maximum gas, then push
for 4-5 second. Released the knob if the fire has turned on and adjusts
the fire by turning the knob to the desired position
For model without electric ignition:
To light the burner without automatic ignition plug, or light the burner at
the condition does n’t have electric power, turn on the fire using matches
and approach the fire to the upper side of burner than push the knob
and turn counter clockwise until the maximum fire symbol condition.
To decrease / increase the fire on turned
on burner:
Turn the knob to the maximum fire symbols or
the minimum fire symbols
To turn off the fire on burner:
Turn the knob to “OFF” symbol

12
Touch Control BH 7723 LLD
Power Button
Press this button once to turn off the appliance, LED display will light up
and the appliance will enter standby mode. To turn off the appliance,
press this button once again and display will be turned off.
Ignition Button
In standby state, press the ignition button of the desired burner once to
light up the flame.
+Plus Button
When the fire had been lit up, press this key to increase the flame. Each
press of the button increases one stage of flame.
-Minus Button
Press this button to reduce the flame. Each press of the button reduces
one stage of flame.
Timer Button
Long press the button to enter timer setting mode. Adjust the timer by
pressing the + and –button, and press the button once again to start the
timer. Long press the button to cancel the ongoing timing process.
NOTE
Checked whether the flame is smooth and blue. If the color is
red/yellow and generates a thundering sound from the burner, turn
off the flame and repeat this until the flame is smooth and blue color

13
Overheat Indicator
After shutting the cooker off, if the temperature on the surface still
exceeds 50℃, the panel will show this indicator until the temperature
decreases.
Ignition and fire control
Press ignition button to ignite the flame, the flame will burn in the biggest
stage, and LED display will show the number 5.
Stages according to the usage:
•Stage 1: Reheating and heat-preserving
•Stage 2: Cooking soup and stews
•Stage 3: Steaming
•Stage 4: Frying/Deep Frying
•Stage 5: Stir-frying
Setting the Timer
•When the burner has been lit, long press timer button to enter
timer setting mode. The LED display will light up.
•Press + and –button to adjust the time that shows up in the LED
display.
•Press the timer button again to start the timer. The display will
show the stage of the burner and the timer alternately. When timer
ends, flame will be put out automatically and the buzzer will ring.
NOTE
The timer can be set between 1-199 minutes

14
Overheat reminder
After the appliance is turned off, if the glass surface exceeds 50℃, the
overheat indicator will light up until the temperature is safe to touch. Pay
attention to avoid touching the glass panel if the indicator is on.
Auto-cutoff protection
If in the middle of cooking process there is a strong wind blowing that
puts out the fire, or spilled food that
causes the fire to burn abnormally, the protective device in the cooker
will automatically cut off the gas flow to prevent further combustion.
Air adjusting device
This appliance is equipped with an air-
adjusting damper to adjust the air inside the
burner for burning process. If the fire is
abnormal (i.e. red, yellow, or unstable),
adjust the damper with a screwdriver until
the fire turns back to normal.
BH 1725 LAT & BH 1725 LBT
Timer controls on left burners. When the timer is set, it will count
backwards. “0”, display shows “OFF”. All burners turn off, warning “BEE”
will sound.
TIMER control
1. “--”, default setting. Connect the power, it sounds “Bee”once and
display show “- -”. 5 second later, display turn off automatically.

15
2. Pressing the TIMER button to control timer ON and OFF.,
3. Press timer button, display shows “ON”. Then set the desired
cooking time by pressing “-”and “+”buttons. This timer can be set
from 1min to 120mins. Once time is set and no future operation, it will
start to count backward automatically.
4. Once set time count backwards to zero, display shows “0”. Warning
“BEE”will sounds until user press any button and turn all burner
control knobs to OFF.
5. If Timer is counting backwards, but all burners turn off by burner
control knob, the timer will keep count backwards to zero, then
display shows “ON”..
How to Use the Burner
To use the burner properly, compare the burner diameter with cooking
equipment diameter. Cooking equipment diameter must be proportional
to the power of burner so we can save the gas usage and fasten the
cooking process.
Burner
Recommended Pot Diameter (cm)
Small
12–14
Medium
14-20
Large
18-26
Double Ring
18-28
Triple Ring
18-28
Diameter of cooking equipment does not exceed the maximum
recommended size based on the above table.
If the diameter exceeds the size of the cooking equipment that has been
recommended, then the hot stove/burner cannot circulate properly, this
can cause the glass top plate broken.
Maximum load of cooking equipment and food ingredients are 10 kg.

16
MODENA gas cooker are designed specifically for long-term use of time
so it does not require complex treatment. However, there are some
things that are encouraged to care for your gas cooker quality.
Enameled Part
Clean enameled layer with sponge and warm soap water. Do Not use the
abrasive detergent. Dry after washing process
Stainless Steel Part
Clean stainless steel part with a wet towel or special detergent for
stainless material. After that, dry it with soft towel.
Grid
Part of enameled grid can be wash or put into the dishwasher
Burner
Burner can be removed and cleaned using soapy water. After cleaning,
dry the burner completely and reinstall it with the right position.
Ignition Plug and Gas Safety Device
Clean the ignition plug and gas safety device after cooking, especially if
there are drops or spills from the pan during cooking
PART 5: MAINTENANCE

17
Problem
Possible
Cause
Recommended Action
Ignition
does not
work
•Battery runs
out.
•Control
knob is not
in maximum
fire position.
•Make sure that the battery is installed
correctly.
•Ensure the battery is still charged
electricity.
•Ensure knob has been pressed and
rotated toward the star symbol.
Gas
Leakage
•Knob is not
in OFF
position.
•Gas leakage
due to
improper
gas hose
and
regulator
installation.
•Ensure all knobs are in the OFF
position.
•Check whether the gas hose and
regulator have been installed
properly.
•Perform a gas leak test at the gas
hose, regulators, and cylinders,
especially on the connectors.
•If you still able to smell the gas,
disconnect the regulator from the
cylinder immediately, do not light a
fire.
•Contact MODENA Call Center for
service.
Fire is not
normal
(Red /
small /
unstable)
•Gas supply
obstructed/i
nterfered.
•Make sure that the holes in the burner
is not clogged with spillovers.
•Clean the burner, including the fire
holes.
•Insufficient
gas amount.
•Check the gas amount on the
regulator’s gas indicator. Make sure
the gas amount is still sufficient.
•Lack of
oxygen
supply due
to improper
air
circulation.
•Make sure that the room’s air
circulation is convenient for gas use.
PART 6: TROUBLESHOOTING

18
•Always lower the heat or turn off the fire before lifting pan from the
burner.
•During cooking process, fat or oil must be carefully treated because
this material can be burn if its reach certain temperature.
•When you smell gas, immediately release the regulator from the gas
tank, do not light a fire and immediately contact MODENA Service
Center.
•Frequently check the gas hose, to make sure that gas hose is far
from hot surface, and Not in bent position. Make sure the outer
surface of hose isn’t cracked so that can be a leakage.
•Always remember that territory around the gas stove can be hot for
the long time (around 30 minutes) after you turn off the gas stove.
•Do the routine service on your built-in hob every 3 (three) month,
because if the is something wrong on your Built-in hob, you can
immediately detect and repair
PART 7: PRECAUTION

19
TYPE
BH 6725 LF
BH 6935 LF
BH 5725 LK
BH 5725 LO
Numbers of Burner
2
3
2
2
Burners Composition
2 Triple Rings
2 Triple Rings
1 Medium
Burner
2 Triple Rings
2 Triple Rings
Gas Safety Device
Yes
Yes
Yes
Yes
Ignition Source
Battery
Battery
Battery
Battery
Material
Glass
Glass
Glass
Glass
Pan Support
Yes
Yes
Yes
Yes
Wok Adaptor
No
No
No
No
Product Dimension (L
x W x H) mm
780 x 450 x 120
820 x 520 x 120
780 x 450 x 120
730 x 420 x 120
Cut-out dimension (L
x W) mm
685 x 400
820 x 475
635 x 350
635 x 350
TYPE
BH 2733 LL
BH 2933 LL
BH 2723 LJ
BH 2933 LJ
BH 7723 LLD
Numbers of
Burner
2
3
2
3
2
Burners
Composition
2 Double
Rings
2 Double
Rings
1 Medium
Burner
2 Double
Rings
2 Double
Rings
1 Medium
Burner
2 Double
Rings
Gas Safety
Device
Yes
Yes
Yes
Yes
Yes
Ignition
Source
Battery
Battery
Battery
Battery
AC Power
Material
Glass
Glass
Glass
Glass
Glass
Pan Support
Yes
Yes
Yes
Yes
Yes
Wok Adaptor
No
No
No
No
No
Product
Dimension (L x
W x H) mm
780 x 480 x
100
865 x 510 x
100
780 x 480 x
100
865 x 510 x
100
780 x 450 x
100
Cut-out
dimension (L x
W) mm
722 x 428
827 x 470
660 X 360
827 x 470
703 x 403
PART 8: SPECIFICATION

20
TYPE
BH 4724
BH 4934
BH 4727
BH 4937
Numbers of Burner
2
3
2
3
Burners Composition
2 Double Rings
2 Double Rings
1 Medium
Burner
2 Double Rings
2 Double Rings
1 Medium
Burner
Gas Safety Device
Yes
Yes
Yes
Yes
Ignition Source
Battery
Battery
Battery
Battery
Material
Glass
Glass
Glass
Glass
Pan Support
Yes
Yes
Yes
Yes
Wok Adaptor
No
No
No
No
Product Dimension (L
x W x H) mm
780x450x100
865x510x100
780x450x100
865x510x120
Cut-out dimension (L
x W) mm
660 x 360
827x470
660 x 360
827x470
TYPE
BH 1725 LA
BH 1725 LB
BH 1935 LA
BH 1935 LB
Numbers of Burner
2
2
3
3
Burners Composition
2 Triple Rings
2 Triple Rings
2 Triple Rings
1 Medium
Burner
2 Triple Rings
1 Medium
Burner
Gas Safety Device
Yes
Yes
Yes
Yes
Ignition Source
Battery
Battery
Battery
Battery
Material
Glass
Glass
Glass
Glass
Pan Support
Yes
Yes
Yes
Yes
Wok Adaptor
Yes
Yes
Yes
Yes
Product Dimension (L
x W x H) mm
730x420x120
730x420x120
865x510x100
865x510x100
Cut-out dimension (L
x W) mm
660x360
660x360
827x470
827x470