Function 1 - Main Switch - Workshop and Diagnostics ( 0=OFF / *1=ON / 2=NO HAZARDS )
The module can quickly and easily be enabled and disabled using this function. It acts like a master switch. When
disabled, the module becomes completely inactive and behaves as if it was not installed.
Setting 0 disables the entire module while keeping all other function settings intact. This allows turning the module off
and back on without the need to reconfigure all of the other user configurable settings.
Setting 2 disables blinking of the hazards during remote operation.
IMPORTANT: In order to avoid problems with diagnostic tools and to avoid confusion or injury by
unexpected top movement, we urge you to ALWAYS DISABLE the module before taking the car to a shop or
lending it to a third person! If problems with the top arise while the module is installed, ALWAYS contact
Mods4Cars first at www.mods4cars.com. NEVER take the car to a dealer without getting support first!
Function 2 - One-Touch top operation ( 0=OFF / *1=ON WU / 2=ON WD / 3=EXT WU / 4=EXT WD )
This function enables one-touch console switch operation, for which the window position after top open as well as an
optional extended convenience mode can be programmed.
Setting 1 is standard one-touch mode with windows up (WU) after top open.
Setting 2 is standard one-touch mode with windows down (WD) after top open.
Settings 3 and 4 (EXTENDED) are the same as 1 and 2 respectively, but it is possible to turn the ignition off and pull
the key out while the top operation continues. It is also possible to get out of the vehicle and lock the doors using the
remote while the top is still closing.
Settings 3 and 4 require extra responsibility and caution to avoid injury by moving top parts to passengers
not expecting the top to continue running after the engine is turned off!
Top operation with the console switch:
• Holding down the switch (>2 sec) in either direction will operate the top in manual mode for as long as the switch is
held.
• Tap open 1x to open the top and bring the windows into the selected position (WU=Windows Up, WD=Windows
Down).
• Tap open 2x to open the top and bring the windows into the opposite position this one time (Down on settings 1 and
3, Up on settings 2 and 4).
• Tap open 2x QUICKLY (like a mouse double-click) to automatically lower windows (SLK) / raise windows (CLK,SL).
• Tap close 1x to close top and windows.
• Tap close 2x to close only the top and leave the windows open.
• Tap close 2x QUICKLY (like a mouse double-click) to automatically raise windows (SLK) / lower windows (CLK,SL).
• Tap in the opposite direction at any time for emergency stop.
PLEASE NOTE: On CLKs model year 2004 the top can be operated while driving, but not using the "one-touch"
feature. This is due to the way the top button is directly wired to the top controller on this model only.
Function 3 - Remote Control ( 0=OFF / *1=ON WU / 2=ON WD / 3=EXT WU / 4=EXT WD )
This function allows full automatic top operation with the original remote fob by pressing the lock and unlock buttons.
Also here it is possible to determine (independently from operation via the center console switch) the position of the
windows after opening the top.
Setting 1 is standard remote mode with windows up (WU) after top open.
Setting 2 is standard remote mode with windows down (WD) after top open.
Settings 3 and 4 (EXTENDED) are the same as 1 and 2 respectively, but it is possible to turn the ignition on and start
the engine while the top still continues. Additionally locking the doors by remote will not interrupt an ongoing top
operation.
Settings 3 and 4 require extra responsibility and caution to avoid injury by moving top parts, as locking
(previously unlocked) doors with the remote will not stop the top!
Top operation with the remote fob:
• Tap unlock on the remote 2x (in 1 sec intervals) to open all windows.
• Tap unlock on the remote 3x (in 1 sec intervals) to open the top and bring the windows into the selected position
(WU=Windows Up, WD=Windows Down).
• Tap unlock on the remote 4x (in 1 sec intervals) to open the top and and bring the windows into the opposite
position this one time (Down on settings 1 and 3, Up on settings 2 and 4).
• Tap lock on the remote 2x (in 1 sec intervals) to close all windows.
• Tap lock on the remote 3x (in 1 sec intervals) to close top and windows.
• Tap lock on the remote 4x (in 1 sec intervals) to close top and leave windows down.
• Tap any direction to stop an ongoing operation. To stop the top in extended mode in any door lock state,
tap the same direction twice!
IMPORTANT: With sequential unlocking enabled (first driver's door, then all others) it is necessary to add
one key press to the sequence when tapping the UNLOCK button (1x = Driver's door unlocks, 2x = All doors
unlock, 3x = Windows roll down etc.)
