modway EEI-3691-NAT-TAU User manual

ABolt M6x80mm x 4
2. Leg Frame 2
3. Back Rail 1
x1
EEI-3691-NAT-TAU CHAIR
Hardware:
Component:
Page 1 of 3
Thank you for purchasing the MODWAY CHAIR!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Customer Service 609-256-9000 www.modway.com
1. Leg Frame 1 x1
1
2
3
4
4. Back Rail 2
B
55. Seat
x1
x3
x2
6. Brace Rail 1
7. Brace Rail 2
x1
x2
6
7
BNut M6 x 4
Allen Wrench M4 x 2
E
8
8. Seat Cushion x1
CScrew M6x50mm x 2
Dx 6
Screw M6x70mm

Attach the 2 pieces of Brace Rail 2 (7) to the Brace Rail 1 (6) as shown. Then insert 2 pieces of Screw (C) through
Brace Rail 2 (7) to the Brace Rail 1 (6). Use Allen Wrench (E) to tighten Screws (C).
x2
C
EEI-3691-NAT-TAU CHAIR
Page 2 of 3
STEP 1:
Hardware & Tool required
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
STEP 2:
7
x1
E
E
Attach Leg Frame 1 (1) to Seat (5) , Back Rail 1 (3) and Brace Rail 2 (7). Insert 3 pieces of Screws (D) through Leg
Frame 1 (1) to Back Rail 1 (3) and Seat (5).Insert 2 pieces of Nuts (B) to the Brace Rail 2 (7), then insert 2 pieces of
Bolts (A) through Leg Frame 1 (1) to the Brace Rail 2 (7). Use Allen Wrench (E) to tighten Bolts (A), Nuts (B) and
Screws (D).
7
6
C
1
3
5
7
x2
A
x2
E
x2
B
x3
D
E
D
E
ABE

Carefully position the assembled chair to the desired location.
EEI-3691-NAT-TAU CHAIR
Page 3 of 3
STEP 3:
Hardware & Tool required
STEP 4:
Assembly is complete. Your chair is ready to be used now!
Customer Service 609-256-9000 www.modway.com
7
x2
A
x2
E
x2
B
x3
D
8
E
D
E
A
B
Put the Seat Cushion (8) into the assembled chair as shown.
3
5
7
2
Attach Back Rail 2 (4) first to the Leg Frame 1 (1) as shown then attach Leg Frame 2 (2) to the assembled Seat (5),
Leg Frame 1 (1), Back Rail (3&4) and Brace Rail (7). Insert 3 pieces of Screws (D) through Legs Frame 2 (2) to Back
Rail 1 (3) and Seat (5). Insert 2 pieces of Nuts (B) to the Brace Rail 2 (7), then insert 2 pieces of Bolts (A) through Leg
Frame 2 (2) to the Brace Rail 2 (7). Use Allen Wrench (E) to tighten Bolts (A) ,Nuts (B) and Screws (D).
E