modway EEI-2531 User manual

Customer Service 908-368-1025︱Page 1 of 11
EEI-2531 SIDEBOARD
A)
Ø 6 x 35 mm x18
F)
x 16
B)
Ø 15 mm x12
C)
Ø 12 mm x 6
D)
Ø 8 x 30 mm
x 4
E)
Ø 6 x 30 mm x 6
L 4
G)
M 6.5 x 10.5 mm
x 1
H)
M 3.5 x 13 mm
x 8
J)
M 7 x 50 mm
x 8
P)
x 16
L)
x 20
M)
Ø 5 x 15 mm
x 18
N)
9 x 14 x 10 mm
x 12
Q)
x 5
R)
x 5
S)
x 8
O)
Ø 15 mm
x 24
T) x 1
Screwdriver (Not Include)
Hardware :
M 8 x 39 mm
M 3.5 x 15.5 mm
Thank you for purchasing the MODWAY SIDEBOARD !
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 60 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Owing to the size and weight of the Sideboard, we recommend that
Cambolt/Metal CamLock Big/Metal CamLock Small/Metal Screw/Metal
Screw/Metal
Screw/Metal
M 3.5 x 15.5 mm
K)
x 24
Screw/Metal Screw/Metal Screw/Metal
Screw/Metal
Dowel Small/Wood
Dowel Big/Wood Hex/Allen Key/Metal Shelf Pin/Metal
HN26C)
x 4
Hinge Set / Metal
350 mm
RM35A)
x 3
Drawer Runner / Metal
PM1)
x 4 70 x 62 x 17 mm
Leg Mounting Plate / Metal
Ø 18 x 29 mm
Door/Drawer Knob/Metal Chrome Screw/Metal
M 4 x 20 mm
Screw Cap / Plastic
Wedge/Plastic
I)
x 4
Ø 8 mm
Bumper /Silicon
M 4 x 16 mm
www.modway.com

Customer Service 908-368-1025︱Page 2 of 11
5Centre Board Right x1
1Top Board x1 2Bottom Board x1
6Adjustable Shelf x2
3Side Board x2
7Wooden Door Left x1 Wooden Door Right x1
4Center Board Left x1
8
9Front Drawer x310 Side Drawer Left x3 11 Side Drawer Right x3 12 Back Drawer x3
13 Bottom Drawer x3 LB18A Leg x4
15 Back Board 1 x2
14 Back Board 2 x2
Components:
1
2
3
3
45
6
6
7
8
9
10
11
12
13
LB18A LB18A
LB18A
LB18A
15
14
14
15
EEI-2531 SIDEBOARD
www.modway.com

Customer Service 908-368-1025︱Page 3 of 11
Ax8Fx16 RM35Ax3 Lx12 Tx1
Hardware required.
Screwdriver not included
STEP 1:
EEI-2531 SIDEBOARD
www.modway.com
1
3
4
5
F
L
RM35A
F
RM35A
L
Connecting Hardware assembly,
Cambolt (A) on Top Board (1)
Insert Small Dowel (F) on Sideboard (3) x 2 pcs
Assembly Drawer Runner (RM35A) on Center Board Left (4) and
Center Board Right (5), using Screw (L). Also insert Big Dowel
(F) on both center boards.

Customer Service 908-368-1025︱Page 4 of 11
STEP 2:
STEP 3:
PM1x4
PM1
Px16 Hardware required.
Screwdriver not included
EEI-2531 SIDEBOARD
Tx1
www.modway.com
2
2
Ax4

Bx8Sx4
Hardware required.
Screwdriver not included
Tx1
1
3
3
B
4
5
S
Securing the Leg Mounting Plate ( O )
to the Bottom Board (2)
Flip the Bottom Board then the Connecting
Hardware assembly, Cambolt (A) on it.
Securing Side Boards ( 3 )x 2 pcs, Center Board
Left (4) and Center Board Right (5) on to Top
Board using Camlock (B), then finish it with
Screw Cap (S).

Customer Service 908-368-1025︱Page 5 of 11
STEP 4:
STEP 5:
EEI-2531 SIDEBOARD
www.modway.com
Bx8Sx4
Hardware required.
Screwdriver not included
Hardware required.
Dx4 Gx1
Tx1
2
LB18A
LB18A
LB18A
LB18A
15
15
14 14
B
S
D
G
Insert Backboard 1 (15)x2 and Backboard 2 (14), then
Securing Bottom Board (2) using Camlock (B) and finish it
with Screw Cap (S).
(15)
Lamination facing front side
Legs (LB18A) assembly

Customer Service 908-368-1025︱Page 6 of 11
STEP 6:
STEP 7:
Hx8Hardware required
Edge with lamination
at front
HN26Cx4
HN26C
Jx8
EEI-2531 SIDEBOARD
Hardware required.
Screwdriver not included
Tx1
www.modway.com
6
6
78
Adjustable Shelf (6) assembly with Shelf Pin (H)
Securing Hinges (HN26C) using Screw (J) onto Door Left (7) and Door

Customer Service 908-368-1025︱Page 7 of 11
STEP 8:
HOW TO ADJUST THE DOOR
EEI-2531 SIDEBOARD
www.modway.com
Hardware required.
Screwdriver not included
Qx2 Rx2 Ix4
I
Q
Tx1
Lx8
7
8
L
Securing Door Left (7) & Door Right (8) with pre-installed
hinges onto each Side Board, using Screw (L).
Securing Door Knob (Q) using Screw (R) to both Wooden
Doors (7)(8).
Adjust the Hinges when necessary.

Customer Service 908-368-1025︱Page 8 of 11
STEP 9:
STEP 10:
Ax2Ex2
Cx2Nx4
EEI-2531 SIDEBOARD
Hardware required. Screwdriver not included
Tx1
Hardware required. Screwdriver not included
Tx1
www.modway.com
Drawer Box parts
Connecting hardware assembly -
Securing Assembly Cambolt (A)
to 1 of the Drawer Front (9), then
Small Dowel (E) to Side Drawer
Left (10) and Side Drawer Right
(11)
Drawer Box assembly
Securing both Side Drawer Left (10) and Side Drawer Right (11) to the Drawer
Front (9) using Small Camlock (C).
Then Slide in Bottom Drawer (13) with laminated side facing inside box. Finish with
securing Back Drawer (12) using Screw (N)

Customer Service 908-368-1025︱Page 9 of 11
STEP 11:
STEP 12:
RM35A
Mx6 Qx1 Rx1
EEI-2531 SIDEBOARD
Hardware required.
Screwdriver not included
Tx1
www.modway.com
Repeat Step 9 - 11 to assembly 2 more drawers
Now you have 3 drawers to complete the sideboard
Securing the other pair of Drawer Runner (RM35A) to the Drawer Box
using Screw (M), continue with Drawer Knob (Q) using Screw (R)

Customer Service 908-368-1025︱Page 10 of 11
STEP 13:
STEP 14:
Ox24
O
Kx24
EEI-2531 SIDEBOARD
Hardware required. Screwdriver not included
Tx1
www.modway.com
Drawer with warning labels on top
WARNING
Children have died from furniture tipover.
To reduce the risk of furniture tipover:
ALWAYS install tipover restraint provided.
NEVER put a TV on this product.
NEVER allow children to stand, climb or
hang on drawers, door or shelves.
NEVER open more than one drawer at a
time.
Place heaviest items in the lowest drawer.
This is a permanent label.
Do not remove!
ATTENTION
Les enfants sont morts de basculement
dans les meubles. Réduire les risques de
renversement de meubles:
TOUJOURS installer la retenue de
renversement fournie.
NE JAMAIS installer de téléviseur sur ce
produit.
Ne JAMAIS LAISSER les enfants se tenir
debout, grimper ou s'accrocher aux tiroirs,
aux portes ou aux étagères.
NE JAMAIS ouvrir plus d’un tiroir à la fois
Placez les articles les plus lourds dans le
tiroir le plus bas.
Ceci est une étiquette permanente.
Ne pas enlever!
Los niños han muertopor vuelco de
muebles. Para reducir el riesgo de
vuelco de muebles:
SIEMPRE instale la restricción del vuelco
provista.
NUNCA cologue un televisor en este
producto.
NUNCA permita que los niños se paren,
trepen o cuelguen en cajones, puertas o
estantes.
NUNCA abra más de un cajón a la vez.
Coloque los artículos más pesados en los
cajón más bajo.
¡No Quitar!
ADVERTENCIA
Drawer Box Fitting - Align both top &
bottom roller and push to fit the void
space
Securing the Back Board using plastic
Wedge (O) with Screw (K)
O
K