modway Motivate Channel EEI-3333 User manual

Component:
EEI – 3333 / 3334 DINING CHAIR
Thank you for purchasing the MODWAY DINING CHAIR!
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the dining chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
Hardware:
A Bolt M6 x 40mm x 2
B Bolt M6 x 60mm x 4
C Bolt M6 x 80mm x 4
D Spring Washer M6 x 10
E Flat Washer M6 x 10
F Allen Wrench x 1
G CSK M4 x 30mm x 4
Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
1
3
3
2
4
4
1 Chair Back x1 2 Seat Frame x1 4 Strecher x2
Right (R)
Left (L)
3 Front Leg (Left &Right)
x2

STEP 1:
Please put Chair Back (1) upside down on a carpeted or padded area.
Then open the black fabric which is attached by the Velcro from back to front on the bottom of the Seat Frame (2). The
inside of the Seat Frame (2) will now be visible.
Attach Seat Frame (2) to Chair Back (1) by using 2 pieces of Bolt (A), 2 pieces of Spring Washer (D) and 2 pieces of Flat
Washer (E) as shown.
Do not fully tighten Bolt (A) at this step.
STEP 2:
Attach Seat Frame (2) to Chair Back (1) by 4 pieces of Bolt (C), 4 pieces of Spring Washer (D) and 4 pieces of Flat Washer
(E) as shown.
Do not fully tighten Bolts (C) at this step also.
EEI – 3333 / 3334 DINING CHAIR
Hardware & Tool required
Hardware & Tool required
Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
A x 2D x 2E x 2
C x 4D x 4E x 4
1
A
E
D
1
E
D
C2
2

STEP 3:
Insert Stretcher (4) into the upper hole on the bottom of Front Leg (3) and Seat Frame (2) as shown.
Insert 1 piece of Front Leg (3) into the upper hole on the bottom of Seat Frame (2) as shown.
Attach by 2 pieces of Bolt (B), 2 pieces of Spring Washer (D) and 2 piece of Flat Washer (E) as shown.
Repeat the same steps for Front Leg (3).
Do not fully tighten Bolts (B) for either leg.
STEP 4:
Attach 1 piece of CSK M4 (G) to the Stretcher (4) to Chair Back (1) and Front Leg (3).
Repeat steps to the other side of the Stretcher.
EEI – 3333 / 3334 DINING CHAIR
Hardware & Tool required
Hardware & Tool required
Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
G x 4
B
E
D
B x 4D x 4E x 4
1
1
3
3
3
4
4
G
2
Right (R)
Left (L)

STEP 5:
Carefully turn over the chair.
Please put a heavy object or seat one adult on top of the Seat Frame (2) to pressure the chair for leveling.
Fully tighten the Bolts (A & B & C) with Allen Wrench (F).
STEP 6:
Please put back Bottom Base Fabric to connection Bottom of Seat Frame (2).
Assembly is complete. The chair is ready to use now!
EEI – 3333 / 3334 DINING CHAIR
Hardware & Tool required
Hardware & Tool required
Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
F x 1
F