modway MOD-6054 User manual

Customer Service 908-368-1025 www.modway.com Page 1/3
Thank you for purchasing the MODWAY BED ！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the nightstand, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approx assembly time: 20 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all small pieces out of reach of children.
MOD-6054, MOD-6055, MOD-6056
1
3
3
2
7
Compenent :
1 - x 1
HEADBOARD
2 - x 1FOOTBOARD
3 - x 2
SIDERAIL
Hardware:
AJCBB BOLT M8 x 20
B
C
8 PCS
CSK SCREW M4 X 32mm
FLAT WASHER 2MM
SPRING WASHER 5/16
4 PCS
4 - x 1
CENTER SUPPORT
4
5
5
5
6
6
5 - x 3SUPPORT LEG
6 - x 2SUPPORT BAR
7 - x 13
BED SLAT
M5 ALLEN KEY
D
E
F
G
H
I
JCBC BOLT M6 x 40
JCBC BOLT M6 x 50
M4 ALLEN KEY LONG WITH BALL
ADJUSTER
5 PCS
8 PCS
8 PCS
6 PCS
1 PC
1 PC
3 PCS

Hardware & Tool required
Customer Service 908-368-1025 www.modway.com Page 2/3
Hardware & Tool required
Hardware & Tool required
Hx1
STEP 1:
1. Attach the Headboard (1) and Footboard (2) into the Siderail(3) as per diagram shown. Place JCBB bolt 20MM(A), Spring washer(D),Flat washer(E)
and tighten by using M5 Allen Key(H).
STEP 2:
1. Attach Support bar(6) into Headbord(1) and Footboard(2) then insert JCBC Bolt 40mm(B) and tighten by using M4 Allen Key(G)
2. Attach Centre Support(4) into Support bar(6) (assemble in step 1) then insert JCBC Bolt 50mm(C) and tighten by using M4 Allen Key(G)as per
diagram.
Ax8
MOD-6054, MOD-6055, MOD-6056
Dx8
Bx4 Cx2 Gx1
Ex8
H

Customer Service 908-368-1025 www.modway.com Page 3/3
Fx6
Hardware & Tool required
Hardware & Tool required
STEP 4:
Attach Slat (7) into bed by inserting CSK screw (F) into the predrilled holes on the Slat (7) . Tighten with Screwdriver (Not provided) .
STEP 3:
1. Attach the Support leg(5) as shown in diagram. Place the JCBC bolt 50MM(D)) and tighten by using M4 Allen Key(G) After, place Adjuster (I) to
bottom support leg(5) as diagram shown.
Screwdriver (Not provided) .
Cx3 Gx1 Ix3
MOD-6054, MOD-6055, MOD-6056