modway EEI-2057 User manual

Customer Service 908-368-1025︱Page 1 of 6
EEI –2057 DESK
Hardware:
Component:
f Allen Wrench x1
A Top Panel x1
Thank you for purchasing the DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
d Short Bolt M6x30mm x8
e Long Bolt M6x55mm x4
a Cam Post x10
b Cam x10
c Dowel x20
g Plastic Cover x1
A
C
D D D D
E
B
F
G
G
H
h Leveler x4
B Left Side Panel x1 C Back Panel x1
D Divider Panel x1 E Right Side Panel x1 F Desk Top x1
G Desk Leg x2 H Bottom Panel x1
f

Customer Service 908-368-1025︱Page 2 of 6
EEI –2057 DESK
HOW TO USE CAN AND CAM POST HARDWARE
1. 2.
3. 4.
Note cam arrow
direction
Note cam arrow
direction
Turn cam clockwise
1/2 turn
5.
STEP 1:
Insert 5pcs Cam Post (a) into the corresponding holes on the Left Side Panel (B) by using a Phillips Head Screw Driver (not
included) as shown.
Repeat the same steps for the remaining Right Side Panel (E).
ax10 Phillips Head Screwdriver
( not included) Hardware & Tool required
B E
a
a
a
a
a a
a
a
a
a

Customer Service 908-368-1025︱Page 3 of 6
EEI –2057 DESK
STEP 2:
STEP 3:
Insert 6pcs Cam (b) into the holes on the bottom of Desk Top (F) as shown.
Insert 1pc Plastic Cover (g) into the top of Desk Top (F) as shown.
Insert 4pcs Cam (b) into the holes on the Back Panel (C) as shown.
cx20 Hardware & Tool required
Insert 4pcs Dowel (c) into the holes on 1pc Divider Panel (D) as shown.
Repeat the same steps for the other remaining 3pcs Divider Panel (D).
Insert 4pcs Dowel (c) into the holes on the Top Panel (A) as shown.
Place the Desk Top (F) and Top Panel (A) to the Divider Panels (D) as shown.
A
F
D
D D D
c c
c
c c
c
c
c c
c c
c c c c
c
A
C
b
b
b
b
b
b
b
b
b
b
D
D D D
bx10 gx1
g g

Customer Service 908-368-1025︱Page 4 of 6
EEI –2057 DESK
STEP 4:
Phillips Head Screwdriver
( not included) Hardware & Tool required
Connect the Left Side Panel (B) and Right Side Panel (E) to the assembled Desk Top (F) /Top Panel (A) and Back
Panel (C) as shown.
Use a Phillips Head Screw Driver (not included) to tighten all the Cams (b) clockwise until secure.
A
C
B
E
F
D
D D D
STEP 5:
ex4 fx1 Hardware & Tool required
Please put the 2 piece of Desk Leg (G) upside down on a carpeted or padded surface.
Attach 2 pieces of Desk Leg (G) into the Bottom Panel (H) by using 4 pieces of Long Bolts (e) as shown.
Use Allen Wrench (f) to tighten the Long Bolts (e) clockwise until secure.
Back
Front e
e
f
e
e
e
e H
G
G
G
H

Customer Service 908-368-1025︱Page 5 of 6
EEI –2057 DESK
hx4
STEP 6:
Screw the 4 pieces of Leveler (h) to the bottom of Desk Legs (G) clockwise until secure.
h
h
h
h
Back
Front
G
G
dx8 fx1 Hardware & Tool required
Please put the assembled Desk Top (F) upside down on a carpeted or padded surface.
Put something under the bottom of the assembled Desk Top (F) for balance.
Attach assembled Desk Legs (G) into the bottom of assembled Desk Top (F) by using 8 pieces of Short Bolts (d) as shown.
Use Allen Wrench (f) to tighten the Short Bolts (d) clockwise until secure.
STEP 7:
G
G
H
Back
Front
F F
G
d
d f
d
d
d
d
H

Customer Service 908-368-1025︱Page 6 of 6
EEI –2057 DESK
Assembly is completed. The desk is ready to enjoy now!
STEP 8:
Carefully turn over the desk.