modway EEI-3680-NAT-TAU CORNER User manual

A
B
G
Bolt M6x110mm x 2
Bolt M6x70mm x 3
Allen Wrench M4 x 2
6. Seat
7. Leg Frame
x1
x1
Hardware:
Component:
Page 1 of 5
Thank you for purchasing the MODWAY CORNER!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the corner, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Customer Service 609-256-9000 www.modway.com
5. Brace Rail x1
1
4
79
8. Back Cushions x2
CNut M6 x 5
Screw M6x45mm x 2
D
E
EEI-3680-NAT-TAU CORNER
Screw M6x60mm x 3
Screw M6x40mm x 4
F
6
23
5
2. Leg 1
3. Back 2
x1
x1
1. Back 1 x1
4. Leg 2 x1
88
9. Seat Cushion x1

Page 2 of 5
STEP 1:
Hardware & Tool required
STEP 2:
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
3G
C
G
E
2
A
G
D
1
G
x1
A
x2
G
x1
C
x1
D
x2
E
x1
G
Attach Back 2 (3) to Back 1 (1) as shown.
Insert Nut (C) into Back 2 (3), then insert 1 piece of Bolt (A) and 1 piece of Screw (D) through Back 1 (1)
into Back 2 (3).
Tighten with 2 pieces of Allen Wrench (G).
Attach Leg 1 (2) to Back 1 (1), Back 2 (3) as shown.
Then insert 2 pieces of Screws (E) through Leg 1 (2) into Back 1 (1), Back 2 (3).
Tighten with Allen Wrench (G).
EEI-3680-NAT-TAU CORNER

5
G
G
D
A
Page 3 of 5
STEP 3:
Hardware & Tool required
STEP 4:
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
4
C
G
G
C
B
G
x1
A
x2
G
x1
C
x1
B
x2
G
x1
C
x1
D
Attach Brace Rail (5) to Leg 2 (4) as shown.
Insert Nut (C) into Brace Rail (5), then insert 1 piece of Bolt (A) through Leg 2 (4) into Brace Rail (5).
Tighten with 2 pieces of Allen Wrench (G).
Attach Brace Rail (5), Leg 2 (4) to Back 2 (3) as shown.
Insert Nut (C) into Back 2 (3), then insert 1 piece of Bolt (B) and 1 piece of Screw (D) through Brace Rail (5),
Leg 2 (4) into Back 2 (3).
Tighten with 2 pieces of Allen Wrench (G).
EEI-3680-NAT-TAU CORNER

7
G
B
x1
D
Page 4 of 5
STEP 5:
Hardware & Tool required
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
G
D
G
C
B
G
C
G
x1
B
x2
G
x1
C
x1
D
x1
B
x2
G
x1
C
Attach Leg Frame (7) to Back 1 (1), Brace Rail (5) as shown.
Insert 1 piece of Nut (C) into Back 1 (1), then insert 1 piece of Bolt (B) and 1 piece of Screw (D)
through Leg Frame (7) into Back 1 (1).
Tighten with 2 pieces of Allen Wrench (G).
STEP 6:
Insert 1 piece of Nut (C) into Brace Rails (5), then insert 1 piece of Bolt (B) through Leg Frame (7)
into Brace Rails (5).
Tighten with 2 pieces of Allen Wrench (G).
EEI-3680-NAT-TAU CORNER

Carefully position the assembled corner to the desired location.
Put 2 pieces of the Back Cushions (8) and 1 piece of the Seat Cushion (9) into the assembled corner as shown.
Page 5 of 5
STEP 7:
Hardware & Tool required
STEP 8:
Assembly is complete. Your corner is ready to be used now!
Customer Service 609-256-9000 www.modway.com
G
F
9
6
x4
F
x1
G
88
Attach Seat (6) to Back 1(1), Brace Rail (5) and Leg Frame (7) as shown.
Then insert 4 piece of Screws (F) through Seat (6) into Back 1(1), Brace Rail (5).
Tighten with Allen Wrench (G).
EEI-3680-NAT-TAU CORNER