modway EEI-2276 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 3
EEI-2276 SWING CHAIR
Hardware:
Components:
A
GSpring x1
Thank you for purchasing the MODWAY SWING CHAIR！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
6
2
1
HSpring Holder x1
KOpen Wrench x1
JAllen Wrench x1
Bolt/Nut M10x55mm x1
BBolt/Nut M10x60mm x4
CBolt/Nut M10x20mm x3
ELeveler x10
FScrew Set M6x15mm x8
1 Left Base x14 Upper Stand x1
2 Right Base x1 3 Lower Stand x1
5 Lower Basket Frame x1 7 Cushion x1
6 Upper Basket Frame x1
5
7
4
3
DScrew Set M6x30mm x2

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 3
EEI-2276 SWING CHAIR
STEP 1:
Ax1 Bx4 Cx3 Dx2 Ex10 Fx8 Gx1 Hx1 Jx1 Kx1
Hardware & Tool required
Please put all chair parts on a carpeted or padded area.
Find hardware package in the box packing Base (1/2) & Stand (3/4).
Place left Base (1) to Right Base (2) as shown.
Secure the back of base by using 3 sets of Bolts/Nuts (C).
Secure the front of base by using 2 sets of Screw Set (D).
Use Allen Wrench (J) and Open Wrench (K) to tighten Bolts/Nuts (C) clockwise until secure.
Use Phillips Head Screw Driver (Not Provided) to tighten Screw Sets (D).
Secure 10 pieces of Leveler (E) into the bottom of assembled Base as shown.
STEP 5:
Insert Spring Holder (H) into the pre-drilled hole at the top of Upper Stand (4) as shown.
Hang the assembled Basket Frame (5/6/7) to Upper Stand (4) by using 1 piece of Spring (G) as shown.
STEP 4:
Attach Upper Basket Frame (6) to Lower Basket Frame (5) as shown.
Secure by using 4 sets of Screw Set (F) .
Use Phillips Head Screw Driver (Not provided) to tighten Screw Set (F) clockwise until secure.
Place Cushion (7) to the assembled Basket Frame (5/6).
STEP 3:
Insert Upper Stand (4) into Lower Stand (3) as shown.
Secure by using 1 set of Bolt/Nut (A) .
Use Allen Wrench (J) and Open Wrench (K) to tighten Bolt/Nut (A) clockwise until secure.
STEP 2:
Attach Lower Stand (3) to the assembled Base as shown.
Secure the back of base by using 4 sets of Bolts/Nuts (B).
Use Allen Wrench (J) and Open Wrench (K) to tighten Bolts/Nuts (B) clockwise until secure.
Basket frame (5/6).
&