modway EEI-2651 User manual

EEI-2651 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 3
4
1
5
5
4
2
2
3
Thank you for purchasing the MODWAY TABLE！
Before you start, here is some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2. Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6. Please keep all fitting out of reach of children.
Hardware:
A
Bolt M8x40mm
x6
B
Bolt M8x70mm
x8
C
Flat Washer M8
x14
D
Allen Wrench M5
x1
Component:
1Table Top x1
2Table Leg x2
3Table Across x1
4Support Rail x4 5Leaf x2

EEI-2651 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 3
STEP 1:
Please put Table Legs (2),Table Across (3) upside down on a carpeted or padded area.
Position Table Across (3) to Table Legs (2) as shown.
Insert 2 pieces of Bolt (A) with 2 pieces of Flat Washer (C) into the pre-drilled holes on Table legs (2) through the pre-drilled
holes on Table Across (3).
Use Allen Wrench (D) to tighten Bolts (A) clockwise until secure.
D
A
A
CC
232
A
C
A
C
Hardware & Tool required
STEP 2:
Please put Table Top (1) upside down on a carpeted or padded area.
Remove I piece of pre-installed bolts from each piece of Support Rail (4).
Position the assembled Table Legs(2),Table Across (3) to Table Top (1) as shown.
Insert 8 pieces of Bolt (B) with 8 pieces of Flat Washer (C) into the pre-drilled holes on Table Top (1) through the
pre-drilled holes on Table Leg (2).
Insert 2 pieces of Bolt (A) with 2 pieces of Flat Washer (C) into the pre-drilled holes on Table Top (1) through the
pre-drilled holes on Table Across (3).
Use Allen Wrench (D) to tighten all Bolts (A&B) clockwise until secure.
3
B
C
4
B
A C
2C2
BB
4
CC
4 1 4
Remove the pre-installed Bolts from each piece of
Support Rail (4).
Hardware & Tool required
Ax4
Cx4
Dx1
Ax2
Bx8
Cx10
Dx1

EEI-2651 TABLE
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 3
STEP 3:
Carefully turn over the assembled table.
If your want to use Leafs (5), please fully extend Support Rails (4) and put Leafs (5) to Support Rails (4) as shown.
Insert the removed 4 pieces of Bolt from step 2 into the pre-drilled holes on bottom of Table Top (1) through the pre-drilled
holes on bottom of Support Rail (4).
Use Allen Wrench (D) to tighten the removed Bolts from step 2 clockwise until secure.
Removed Bolts from Step 2
Hardware & Tool required
STEP 4:
Position the assembled table to the location your desire.
Assembly is complete. Your table is ready to be used now!
5
1
4
5
4
4
2
2
3
D
Dx1