modway EEI-2711 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 4
EEI-2711 CHAISE
Hardware:
Component:
1 Chaise Body x1
Thank you for purchasing the MODWAY CHAISE！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the chaise, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
A Bolt M6x90mm x 8
F Allen Wrench M4 x 1
B Castor Bolt x 2
1
3
4
2
2 Front Frame x1 3 Back Frame x1
C Small Washer x 2
E Nut x 2
C Large Washer x 2
4 Caster x2 5 Cushion x1
5

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 4
EEI-2711 CHAISE
STEP 1:
Please put Chair Body (1) upside down on a carpeted or padded area.
Insert the tenon on Front Frame (2) into the rabbet on the Chaise Body (1).
Insert the tenon on Back Frame (3) into the rabbet on the Chaise Body (1).
STEP 2:
1
Carefully turn over the assembled Chaise Body (1), Front Frame (2) and Back Frame (3).
Insert 4 pieces of Bolt (A) into the pre-drilled holes on Front Frame (2) through the pre-drilled holes on Chaise Body (1).
Repeat the same steps for the Back Frame (3).
Use Allen Wrench (F) to tighten all Bolts (A) clockwise until secure.
2
3
A
2
Back
Front
1
3
Hardware & Tool required
Ax8 Ex1
Front
Back
A
A A
F
A A
A
A

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 4
EEI-2711 CHAISE
STEP 3:
STEP 4:
Position Casters (2) to the Back Frame (3) as shown.
Insert 1 piece of Caster Bolt (B) with 1 piece of Large Washer (C) and 1 piece of Small Washer (D) into the pre-dilled
holes on the Back Frame (3) through the holes on each Caster (4).
Use 2 pieces of Nuts (E) to tighten Caster Bolts (B) by hand.
Position the assembled chaise to the location your desired.
The height of the back part on Chaise Body (1) is adjustable if you want.
Hardware & Tool required
Bx2 Cx2 Ex2 Dx2
Height adjustable back part of Chaise Body
Back
Front
2
1
3
4
E
D
B
C
3
4
1
B
C
D
E

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 4
EEI-2711 CHAISE
STEP 5:
Put Cushion (5) into the assembled chair as shown.
Tie Cushion (5) to Chaise Body (1) by using the banding on the bottom of Cushion (5) as shown.
Assembly is complete. Your Chaise table is ready to be used now!
5
Banding on the bottom of cushion