modway EEI-2803 User manual

Long Bolt 1/4”x20mm x 8
Before you start, here are some helpful advice:
Page 1 of 4
Hardware:
Component:
ADouble-End Bolt x 4
1
Thank you for purchasing the BAR TABLE!
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bar table, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
CFlat Washer 1/4” x 16
4
3
Table Glass x12 Table Top x1 3 Table Leg x4
1
2
B
EAllen Wrench 1/4” x 1
4 Stretcher x1
33
3
DNut 1/4” x 4
FWrench 1/4” x 1
GPlastic Cover x 4
HSpring Washer 1/4” x 8
Hammer (Not provided)

This side with middle of pre-drilled
holes face toward to the another leg.
Page 2 of 4
BAR TABLE
STEP 1:
2
Hx4 Cx4FX1 Hardware & Tool required
Please put Table Top (2) upside down on a carpeted or padded area.
Fully secure 4 pieces of Double-End Bolt (A) with 4 pieces of Spring Washer (H), 4 pieces of Flat Washer (C) into the bottom of
Table Top (2) as shown.
Secure the assembled Nuts (D) towards Table Top (2) by hand as shown.
Insert Wrench (F) without handle into the assembled Double-End Bolts (A) and use Wrench (F) fully secure Nuts which pre-
assembled on Double-End Bolts (A) by inserting half of handle into Wrench (F) as shown.
A
A
A
A
C
H
D
D
C
H
D
C
H
D
C
H
F
DA
H
C
A
D
Handle
STEP 2:
Put 4 pieces of Table Leg (3) to Table Top (2) through the assembled Double-End Bolt (A) as shown.
2
3
3
3
3
Note:

Page 3 of 4
BAR TABLE
STEP 3:
Place Stretcher (4) to the assembled Table Top (2) and Table Legs (3) as shown.
Insert 8 pieces of Bolt (B) with 8 pieces of Flat Washer (C) into the holes on Table Leg (3) through the holes on Stretcher (4).
Use Allen Wrench (E) to tighten Bolts (B) clockwise until secure.
Bx8 Cx8 Ex1
2
3
3
3
3
4
4
3C
B
E
Hardware & Tool required
Dx4 Fx1Hx4 Cx4
Secure 4 pieces of Nut (D), 4 piece of Spring Washer (H), and 4 pieces of Flat Washer (C) to the other end of assembled
Double-End Bolt (A) as shown.
Use Wrench (F) to tighten Nuts (D) clockwise until secure.
2
3
3
3
3
D
C
F
4
STEP 4:
H
F
D
C
H
3
Hardware & Tool required
F
D
C
H
F
D
C
H
F
D
C
H

Page 4 of 4
BAR TABLE
STEP 5:
Insert 4 pieces of Plastic Cover (G) into the assembled Table Leg (3) by using Hammer (Not provided) as shown.
Gx8 Not Provided Hardware & Tool required
3
3
2
3
3
4
G
G
G
G
STEP 6:
Carefully turn over the assembled bar table.
Put Table Glass (1) to the Table Top (2) as shown.
1
2
3
3
3
3
4
Assembly is complete. Your bar table is ready to be used now!