modway EEI-3700-NAT User manual

1. Table Top
2. Leg Frame x2
Hardware:
Component:
Page 1 of 5
Thank you for purchasing the MODWAY TABLE!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the lounger, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
Customer Service 609-256-9000 www.modway.com
1
x1
EEI-3700-NAT TABLE
A
C
E
Bolt M6x80mm x 4
Bolt M6x40mm x 2
Allen Wrench M4 x 2
B
Nut M6 x 6
Screw M6x60mm x 8
D
3. Brace Rail 1 x2
4. Brace Rail 2 x1
2
3
4

Page 2 of 5
STEP 1:
Hardware & Tool required
STEP 2:
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
1
2
E
A
C
EEI-3700-NAT TABLE
3
DE
x4
D
x1
E
E
x2
A
x2
E
x2
C
Attach Brace Rails 1 (3) to Table Top (1) as shown.
Then insert 4 pieces of Screws (D) through Brace Rails 1 (3) into Table Top (1).
Tighten with Allen Wrench (E).
Attach Leg Frame (2) to Brace Rails 1 (3) as shown.
Insert 2 pieces of Nuts (C), then insert 2 pieces of Bolts (A) through Leg Frame (2) into Brace Rails 1 (3).
Tighten with 2 pieces of Allen Wrench (E).

4
2
EEI-3700-NAT TABLE
E
C
Page 3 of 5
STEP 3:
Hardware & Tool required
STEP 4:
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
B
E
E
A
C
E
Attach Brace Rail 2 (4) to Leg Frame (2) as shown.
Insert 1 piece of Nut (C) into Brace Rail 2 (4), then insert 1 piece of Bolt (B) through Legs Frame (2)
into Brace Rail 2 (4).
Use 2 pieces Allen Wrench (E) to tighten .
Attach Leg Frame (2) to Brace Rails 1 (3) as shown.
Insert 2 pieces of Nuts (C) into Brace Rails 1 (3), then insert 2 pieces of Bolts (A) through Leg Frame (2)
into Brace Rails 1 (3).
Use 2 pieces Allen Wrench (E) to tighten.
x2
A
x2
E
x2
C
x1
B
x2
E
x1
C

E
D
EEI-3700-NAT TABLE
Page 4 of 5
STEP 5:
Hardware & Tool required
STEP 6:
Hardware & Tool required
Customer Service 609-256-9000 www.modway.com
E
C
B
E
Insert 1 piece of Nut (C) into Brace Rail 2 (4).
Then insert 1 piece of Bolt (B) through Leg Frame (2) into Brace Rail 2 (4).
Use 2 pieces Allen Wrench (E) to tighten .
Insert 4 pieces of Screws (D) through Legs Frame (2) into Table Top (1).
Tighten using Allen Wrench (E).
x1
B
x2
E
x1
C
x4
D
x1
E

Page 5 of 5
STEP 7:
Customer Service 609-256-9000 www.modway.com
Carefully position the assembled table to the desired location.
EEI-3700-NAT TABLE
Assembly is complete. Your table is ready to be used now!