modway Exceed EEI-2992 User manual

EEI –2992 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 5
Thank you for purchasing the MODWAY OFFICE CHAIR.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
A. Bolt M6x30mm x 4
B. Bolt M6x35mm x 4
C. Bolt M6x18mm x 4
D. Cover x 4
E. Allen Wrench x1
Component:
1 Base x1 2 Cylinder Column x1 3 Control Mechanism x1 4 Seat x1 5 Back Frame x1
6 Right Arm x1 7 Left Arm x1 8 Castor x5 9 Round casing x1
1
2
5
6 7
8 8
9
3
4

EEI –2992 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 5
STEP 1:
Please put Base (1) on a carpeted or padded surface.
Insert 1 piece of Castor (8) into the Base (1) as shown by hand. Repeat the same steps for the remaining 4
pieces of Castors (8).
STEP 2:
Carefully turn over the assembled Base (1) from step 1.
Insert the Cylinder Column (2) and Round casing (9) as shown.
8
8
8
8
8
1
1
2
2
1
9
2
9

EEI –2992 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 5
STEP 3:
Attach Right Arm (6) and Left Arm (7) to the both side of Back Frame (5) by using 4 pieces of Bolts (B) as
shown.
Tighten Bolts (B) by using Allen Wrench (E) as shown.
Hardware & Tools required
STEP 4:
Attach Cap Cover (D) to the holes on Right Arm (6) and Left Arm (7) by hand as shown.
Hardware & Tools required
B
x 4
x 1
E
B
E
5
7 6
7 6
D D
5
D
x 4

EEI –2992 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 5
STEP 5:
Attach assembly unit in step 4 to the Seat (4) by using 4 pieces of Bolts (A) as shown.
Tighten Bolts (A) by using Allen Wrench (E) as shown.
Hardware & Tools required
STEP 6:
Attach Control Mechanism (3) to the Seat (4) by using 4 pieces of Bolts (C) as shown. Tighten Bolts (C) by
using Allen Wrench (E) as shown.
Hardware & Tools required
A
E
6 7
4
5
A
x 4 x 1
E
C
x 4
x 1
E
6 7
4
C
E
3

EEI –2992 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5 of 5
STEP 7:
Insert assembled Control Mechanism (3) into the Cylinder Column (2) as shown.
STEP 8:
Assembly is complete. Your office chair is ready to be used now!
3
4
1
2
5
6 7
8 8
9
2
3