modway MOD-5473 User manual

t it is intended for. Approximately
Allen Wrench M6 x1
Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 3
MOD-5473/5474 FULL/QUEEN BED FRAME
Hardware:
Component:
ABolt M8x20mm x16
BNut M6 x9
CAllen Wrench M8 x1
1Short Board
Thank you for purchasing the MODWAY FULL/QUEEN BED FRAME！
Before you start, here aresome helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the bed frame, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room tha assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
DOpen Wrench x1
ESide Plastic Cover x24
2Long Board x2 3Leg x4
5Center Rail x1 6Support Leg x4
3
1
12
2
3
3
3
4
56
7
4Stretcher x1
7Slat x24
GBolt M6x55mm x1
HBolt M6x35mm x10
JCenter Plastic Cover x12
F
KFlat Washer x13
IBolt M6x20mm x4
x
LFlat Washer x16
M8
M6

Support
llen Wrench (C) .
Flat washer M8 (L)
Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 3
MOD-5473/5474 FULL/QUEEN BED FRAME
STEP 1:
Insert the end of Leg (3) into Short Board (1) and Board
(2) as shown.
Secure by using 4 pieces of Bolts
(A) ,tighten Bolts (A) by using A
Repeat the same steps for the remaining 3 pieces of Legs (3).
.
Ax16 Cx1 Hardware & Tool required
1
1
2
2
3
3
3
3
3
21
AAAA
C
Bx8 Fx1 Hx8 Ix4 Dx1 Kx12 Hardware & Tool
STEP 2:
Place 1 piece of Support Leg
(6) under Center Rail (5) as shown.
Insert 2 pieces of Bolts (H) through the holes on Center Rail (5) into the holes on Support Legs(6 )
as shown.
Tighten Bolts (H) with 2 pieces of Nuts (B)/Flat Washer (K) by using Allen Wrench (F) and Open Wrench (D) until Secure.
Secure one end of Center Rail (5) by using 2 pieces of Bolts (I) with 2 pieces of Flat Washers (K) as shown.
Tighten Bolts (I) by using Allen Wrench (F)
Repeat the same steps for the other end of Center Rail (5).
1
1
2
2
5
6
6
5
6
1
5
I
K
I
F
H
H
D
B
B
F
K
K
K
Lx16
LLLL
6
6
Dot not fully tighten Bolts (A) at this step.
the middle
Dot not fully tighten Bolts (H) at this step.
Repeat the same steps
for the remaining Legs (6) .
1
23
insert
Long
and

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 3
MOD-5473/5474 FULL/QUEEN BED FRAME
STEP 4:
Insert 2 pieces of Side Plastic Cover (E) into each end of 2 pieces of Slats (7) as shown.
Insert the other end of the Slats (7) into 1 piece of Center Plastic Covers (J) as shown.
Insert the assembled Side Plastic Covers (E) into the corresponding holes on Long Board (2),and insert the assembled Center
Plastic Cover (J) into the corresponding holes on Center Rail (5)as shown.
Repeat the same steps for the remaining 22 pieces Slats (7).
Ex24
Hardware & Tool required
1
7
4
E
E
21
2
Hx2 Bx1 Fx1 Gx1 Dx1
STEP 3:
Place Stretcher (4) to the
assembled Long Board (2) and Center Rail (5) as
shown.
Secure the end of Stretcher (4) by using 2 pieces of Bolts (H) as shown.
Secure the middle of Stretcher (4)
by using 1 piece of Bolt (G)
and Flat Washer (K).
Tighten Bolts (G) by using Allen Wrench (F ) and Nut (B).
Hardware & Tool required
2
4
2
2
1
4G
F
1
5
6
6
1
5
4
H
F
7
5
J
Assembly is complete. Your bed frame is ready to be enjoyed now!
Jx12
DB
K
Kx1
6
6
middle holes of
Dot not fully tighten Bolts (G) at this step.
Please fully tighten all Bolts(A)(G)(H)(I).