modway EEI-2666 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 3
EEI-2666 TABLE
Hardware:
Component:
A Bolt M12x70mm x1
B
1 Table Top x1
Thank you for purchasing the MODWAY TABLE！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the table, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Spring Washer M12 x1
2 Connect Plate x1
D
1
4 Table Base x1
2
4
3 Table Post x1
Allen Wrench M10 x1
E Bolt M6x20mm x3
F Spring Washer M6 x3
G
H
Flat Washer M6 x3
Allen Wrench M4 x1
J Bolt M8x17.5mm x4
K Spring Washer M8 x4
L
M
Flat Washer M8 x4
Allen Wrench M5 x1
Washer M12 x1
C
3

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 3
EEI-2666 TABLE
STEP 1:
Ax1 Bx1 Dx1 Cx1 Hardware & Tool required
STEP 2:
3
D
Please put Post (3) and Table Base (4) upside down on a carpeted or padded area.
Position Table Base (4) to the bottom of Post (3) as shown.
Insert 1 piece of Bolt (A) with 1 piece of Spring Washer (B) and 1 piece of Washer (C) into the hole on bottom of
Post (3) through the hole on Table Base (4).
Use Allen Wrench (D) to tighten Bolt (A) clockwise until secure.
4
A
B
Ex3 Fx3 Gx3 Hx1 Hardware & Tool required
4
The bottom of Table Base
Carefully turn over the assembled Post (3) and Table Base (4).
Position Connect Plate (2) to Post (3) as shown.
Insert 3 pieces of Bolt (E) with 3 pieces of Spring Washer (F) and 3 pieces of Flat Washer (G) into the holes on Post
(3) through the holes on Connect Plate (2).
Use Allen Wrench (H) to tighten all Bolts (E) clockwise until secure.
3
2
E
F
G
G
E
F
G
F
H
E
C

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 3
EEI-2666 TABLE
STEP 3:
Hardware & Tool required
STEP 4:
1
Assembly is complete. Your table is ready to be used now!
Carefully turn over the assembled table.
J
2
Please put the Table Top (1) and the assembled Connect Plate (2), Post (3), and Table Base (4) upside down on a carpeted or
padded area.
Position the assembled Connect Plate (2) to the bottom of Table Top (1) as shown.
Insert 4 pieces of Bolt (J) with 4 pieces of Spring Washer (K) and 4 pieces of Flat Washer (L) into the holes on bottom of
Table Top (1) through the holes on Connect Plate (2).
Use Allen Wrench (M) to tighten Bolt (J) clockwise until secure.
3
4
K
L
M
L
L L
K
K K
J
J
J
Jx4 Kx4 Lx4 Mx1