Mohawk System-IA-10 Technical Document

Turf Kit w Dual Troughs 7-25-2016.DOC
PART # 601-800-XXX
MOHAWK
MADE IN THE USA
OPTIONAL EQUIPMENT MANUAL
MODELS
System-IA-10 / LC-12 / LMF-12 / TP-16 / TP-18
MOHAWK RESOURCES LTD.
MOHAWK INDUSTRIAL PARK
65 VROOMAN AVE. P.O. BOX 110
AMSTERDAM, NY 12010
TOLL FREE : 1-800-833-2006
LOCAL : 1-518-842-1431
FAX : [phone]
INTERNET: www.MOHAWKLIFTS.com
E-MAIL: [email protected]
Turf Kit w/ Dual
Troughs

TURF KIT WITH DUAL TROUGHS
TURF KIT WITH DUAL TROUGH KIT FOR MOHAWK 2-POST
LIFTS
APPLICATION:
THIS KIT IS DESIGNED TO BE ADDED TO A MOHAWK 2-POST LIFT, TO PROVIDE 2
TROUGHS FOR SUPPORT OF TURF / MOWER EQUIPMENT. THESE TROUGHS CAN BE
ADJUSTED TO ACCOMMODATE A VARIETY OF WHEELBASED VEHICLES. THE
FOLLOWING KITS ARE COVERED IN THIS MANUAL:
P/N 009-012-001 TURF KIT W/ DUAL TROUGHS, 6,000 LB MAX CAPACITY
(3000 LBS PER TROUGH)*
(CONVERTS FRAME ENGAGING LIFT INTO TURF MAINTENANCE
LIFT) FOR SYSTEM IA-10 (STANDARD ARMS)
P/N 015-011-076 TURF KIT W/ DUAL TROUGHS, 6,000 LB MAX CAPACITY
(3000 LBS PER TROUGH)*
(CONVERTS FRAME ENGAGING LIFT INTO TURF MAINTENANCE
LIFT) FOR LC-12/LMF-12/TP-16/TP-18 (OPTIONAL 3-STAGE ARMS)
P/N 015-011-081 TURF KIT W/DUAL TROUGHS, 6,000 LB MAX CAPACITY
(3000 LBS PER TROUGH)*
(CONVERTS FRAME ENGAGING LIFT INTO TURF MAINTENANCE
LIFT) FOR LC-12/LMF-12/TP-16/TP-18 (STANDARD ARMS)
*ADAPTER LIMITATIONS AND CAPACITY:
THESE ADAPTERS ARE RATED ACCORDING TO TIRE WIDTH OF VEHICLES
AS BELOW:
TROUGH CAPACITY: TIRE CENTER WIDTH:
3000 LBS 42 INCH MINIMUM
2500 LBS 31 INCH MINIMUM
2000 LBS 15 INCH MINIMUM
1500 LBS N/A (NO RESTRICTION)

TURF KIT WITH DUAL TROUGHS
WARNINGS:
USE OF THE TURF KIT WITH DUALS REDUCES THE LIFTING CAPACITY OF THE ENTIRE
LIFT TO 6000 LBS. TOTAL ( 3000 LBS. PER TROUGH )
DO NOT USE SINGLE TROUGHS TO SUPPORT ONE END OF A VEHICLE.
ALWAYS ENSURE TROUGHS ARE EVENLY SPREAD FROM CENTER OF POSTS.
ALWAYS ENSURE RETAINER PINS ARE SECURELY INSERTED INTO ENDS OF EACH
TROUGH.
ENSURE VEHICLE IS CENTERED BETWEEN POSTS.
INSTALLATION AND SETUP INSTRUCTIONS
WITH LIFT FULLY LOWERED, SWING ALL ARMS TO A FULLY WIDE POSITION PROVIDING
CLEAR PATH BETWEEN LIFT.
FULLY EXTEND ALL ARMS BY PULLING SLIDERS TO MAXIMUM EXTENSION ON ALL
ARMS.
PLACE ARM COVERS OVER ALL ARMS. ENSURE PINS GO COMPLETELY THRU SLIDER
HOLES AND COVER SITS FLAT OVER SWING ARM TUBES.
PLACE TROUGHS OVER OPPOSING SWING ARM COVERS. RETAIN WITH SPRING PINS IN
HOLES PROVIDED IN SWING ARM COVERS.
SPREAD DISTANCE BETWEEN TROUGHS AS DESIRED, ENSURING RETENTION PIN
ACTUATES.
ALWAYS ENSURE TROUGHS ARE EVENLY SPREAD FROM CENTER OF POSTS.

TURF KIT WITH DUAL TROUGHS
USAGE:
MEASURE WHEELBASE OF VEHICLE TO BE LIFTED. ADJUST WIDTH OF TROUGHS TO
MATCH THIS DIMENSION (AS CLOSELY AS POSSIBLY).
ALWAYS ENSURE TROUGHS ARE EVENLY SPREAD FROM CENTER OF POSTS.
WITH LIFT FULLY LOWERED, SLOWLY DRIVE VEHICLE OVER TROUGHS (KEEPING
VEHICLE CENTERED BETWEEN POSTS) UNTIL BOTH SETS OF TIRES ARE ON TROUGHS.
ENSURE THAT ONE SET OF TIRES RESTS FIRMLY AGAINST WHEEL CHOCKS OF TROUGH.
USE ENCLOSED WHEEL CHOCKS FOR SMALLER DIAMETER TIRES TO ENSURE TIRES ARE
FIRMLY SECURED FROM MOVING IN TROUGHS.
RAISE AND USE LIFT AS NORMALLY.

TURF KIT WITH DUAL TROUGHS
MOHAWK
MADE IN THE USA
Turf Kit with Dual
Troughs
DRAWINGS