MOLEAER KINGFISHER User manual

For safety, follow all local electrical codes. Kingsher comes
standard with ozone generation, though it can be bypassed.
See the Owner’s Manual for instructions. EPA Establishment Number 94231-CA-1
Notes
Unpacking
Installation
Scan to Download the Owner’s Manual
and access warranty information for the
Kigsher Nanobubble Generator.
www.moleaer.com
Ensure all accessories were
provided with your Kingsher. Contact
Moleaer for replacement parts. Inspect
outer surfaces for shipping damage.
Open the lid and remove packaging and
accessories from the inside.
Inspect components inside of the
unit for any loose tubing or damaged
components and tighten any loose
ttings or tubing.
NANOBUBBLE GENERATOR
Quick Start Guide
1.1
1. 2
1
2
Install the unit on a
level surface. Pavers
can be used to provide
a level surface.
Position unit within three
feet of a standard three-
prong 120-volt outlet
(15-amps). Extension
cords should not be used.
Position the unit on the
shore as close to the
body of water as possible.
Unit Position & Location:
+1.424.558.3567
A Cleaning Kit (Syringe, Tube, Connector),
B Pump Union, C Pipe Union,
D Pump Union O-Rings,
E Basket Strainer O-Ring, F Suction Strainer,
G Set of Cabinet Keys
1.3
Attach Piping
3
3 .1
3.2
2 .1
2.2
2.3
Using PVC glue (not included), attach hard or exible PVC piping
to the two included connectors, taking note of the orientation of the
intake and discharge and the location of the tank. Connection size is
1.5" and hard PVC piping should be 1.5" for inlet and discharge.
Note 1: The intake and discharge piping should
be as short as possible. Do not exceed 20 feet for
either the intake or discharge pipes.
Note 2: The unit should not be placed more than
six feet above the nominal water level.
Refer to owner’s manual piping placement
and pump restrictions.
Included glue-able connections should be hand
tightened only, do not use tools to tighten onto
the pump or discharge. Ensure all connections
are tight before beginning startup steps.
A B
C
D
F
GE

Startup
NANOBUBBLE GENERATOR |Quick Start Guide
Scan to Download
the Owner’s Manual
and access warranty
information for the
Kingsher Nanobubble
Generator.
www.moleaer.com
Copyright © 2022 Moleaer. All trademarks stated herein are the property of their
respective company. All rights reserved. This document is condential and contains
proprietary information of Moleaer Inc. Neither this document nor any of the
information contained herein may be reproduced, redistributed or disclosed under any
circumstances without the express written permission of Moleaer Inc. Rev. 07-26-22 R5
Please contact Moleaer with any
questions or concerns: +1.424.558.3567
4
Plug the unit power
cord into the GFCI outlet.
Open the lid of the
Kingsher and hand-tighten
any loose ttings.
Using a bucket, prell
the pump basket
with approximately
one gallon of water.
Check that water is owing
through the pump by
verifying that the strainer
basket is lled with water.
If the pump does not prime after several minutes, turn the Kingsher off,
review all suction pipe eld connections to ensure airtight connections,
all valves are open, and try again. Wait ve minutes before re-priming
to allow the pump seals to cool. Consider installing a swing style check
valve to stop water from draining from the the suction pipe.
Once primed, large bubbles or a large air pocket should not be visible
in the strainer basket. Any visible large bubbles or an air pocket in
the strainer basket is an indication of a suction pipe leak. Check suction
pipe for leaks and ensure all pipe connections are airtight.
Once the pump is primed and the system is pumping water, visually
check for leaks inside the unit and hand tighten any ttings that may be
leaking, if hand tightening doesn’t stop leaks, shut the unit down, close any
isolation valves, and disassemble the connections to inspect for any
pinched o-rings and that pipes are aligned properly and reassemble.
Loosen the strainer
basket lid from the
pump by turning it
counterclockwise.
Turn the Kingsher on by pushing the start button.
When the pump strainer
lls with water, tighten the
pump strainer basket lid by
turning the lid clockwise.
4.24 .1
4.5
4.3
4.6
4.4
4.7
4.8