molex 207129 Series User manual

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 1 of 9
Revision: D Revision Date: 06-30-11
Application Tooling
Specification Sheet
Tool Kit
Order No. 6 811-5270
Hand Crimp Tool
Order No. 6 811-5200
FEATURES
% A full cycle ratcheting hand tool ensures complete crimps
% Ergonomically designed soft handles
% Precisely designed crimping profiles with simple contact positioning
% Easy handling due to outstanding force ratio
 Tool kits are easily installed into the Hand Crimp Tool or the 63816-0300 Power Crimp Head which is installed
into the 63816-0200 (110 V) or the 63816-02 0 (220 V) Battery Powered Tool.
 Many different Tool kits can be used with a single Battery Powered Tool.
 This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant.
SCOPE
Products: 2. 0mm (.098”) Pitch SPOX™ Wire-to-Board and Wire-to-Wire Crimp Terminal, 22-28 AWG.
Terminal
Series No.
Terminal Order No. Wire Size Insulation Diameter Strip Length
Loose Piece Reel AWG mm² mm In. mm In.
103
08-70-00 7 08-70-00 6 39-00-0188
22-28 0.3 -0.08 1.1 -1.90 .04 -.07 3.30-3.80 .130-.1 0
08-70-00 9 08-70-00 8 39-00-0387
39-00-0189 08-700-0 69 39-00-0388
08-700-0 89 39-00-0389
39-00-0390
263
08-70-1040 08-70-1039 39-00-01 1
22-28 0.3 -0.08 1.1 -1.90 .04 -.07 3.30-3.80 .130-.1 0 08-70-1046 08-70-104 39-00-01 9
39-00-01 2 39-00-0160
4 627 4 627-1002 4 627-0002 22-24 0.3 -0.20 1.1 -1.90 .04 -.07 3.30-3.80 .130-.1 0
4 627-9002
0802 0802-8100 0802-8000 22-24 0.3 -0.20 1.1 -1.90 .04 -.07 3.30-3.80 .130-.1 0
0802-9101 0802-9001
Customer to cut off terminal from reel: 0.30mm (.012”) maximum Cut-off Tab.
See Conditions on page 2.
TYPE 2C

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 2 of 9
Revision: D Revision Date: 06-30-11
INSULATION
CRIMP
▲
SEE NOTE
BRUSH
STRIP
LENGTH
BELL MOUTH
BEND
DOWN
BEND UP
ROLLING
CONDUCTOR
CRIMP
TWISTING
CRIMP HEIGHT
OVERLAP
INSULATION
CRIMP
OVERLAP FORM
GEOMETRY
ANVIL
PUNCH
WIRE
DEFINITION OF TERMS
The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the
scope.
▲Insulation Crimp Note:
Due to the terminal’s insulation grip design and/or
insulation diameter range, this tool uses “overlap” form
geometry in the insulation punch. This produces an
overlap insulation crimp (A620 – compliant). While the
insulation punch profile may appear “lopsided”, this is a
normal condition for this tool. See figure to the right.
(Some tools with multiple crimp pockets may not have
the “overlap” profile on all pockets).
CONDITIONS:
After crimping, the conductor profiles should measure the following (See notes below).
Terminal
Series No.
Hand
Tool
Locator
Wire Size Conductor Crimp Insulation Crimp Pull Force
Minimum  Profile
Height (Ref.) Width (Ref.) Height (Ref.) Width (Ref.)
AWG mm2 mm In. mm In. mm In. mm In. N Lb. A B C
103
1 22 0.3 0.73-0.80 .029-.031 1.40 .0 1.68 .066 1.90 .07 44.48 10.0 X
1 24 0.20 0.67-0.74 .026-.029 1.40 .0 1. 7 .062 1.90 .07 28.91 6. X
1 26 0.12 0.63-0.69 .02 -.027 1.40 .0 1.42 .0 6 1. 0 .0 9 17.79 4.0 X
1 28 0.08 0.61-0.67 .024-.026 1.40 .0 1.42 .0 6 1. 0 .0 9 11.12 2. X
263
1 22 0.3 0.73-0.80 .029-.031 1.40 .0 1.68 .066 1.90 .07 44.48 10.0 X
1 24 0.20 0.67-0.74 .026-.029 1.40 .0 1. 7 .062 1.90 .07 28.91 6. X
1 26 0.12 0.63-0.69 .02 -.027 1.40 .0 1.42 .0 6 1. 0 .0 9 17.79 4.0 X
1 28 0.08 0.61-0.67 .024-.026 1.40 .0 1.42 .0 6 1. 0 .0 9 11.12 2. X
0802
1 22 0.3 0.73-0.80 .029-.031 1.40 .0 1.68 .066 1.90 .07 44.48 10.0 X
1 24 0.20 0.67-0.74 .026-.029 1.40 .0 1. 7 .062 1.90 .07 28.91 6. X
1 26 0.12 0.63-0.69 .02 -.027 1.40 .0 1.42 .0 6 1. 0 .0 9 17.79 4.0 X
1 28 0.08 0.61-0.67 .024-.026 1.40 .0 1.42 .0 6 1. 0 .0 9 11.12 2. X
4 627 2 22 0.3 0.73-0.80
.029-.031 1.40 .0 1.68 .066 1.90 .07 44.48 10.0 X
2 24 0.20 0.67-0.74 .026-.029 1.40 .0 1. 7 .062 1.90 .07 28.91 6. X

To Achieve IPC-A-620 Class 2 crimps. The following over-all wire insulation diameter ranges are recommended:
1. Profile A: 1.20-1.90mm (.047-.07 inch)
2. Profile B: 1.20-1. mm (.047-.061 inch)
3. Profile C: 1.1 -1.30mm (.04 -.0 1 inch)

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 3 of 9
Revision: D Revision Date: 06-30-11
Tool Qualification Notes:
1. Pull Force should be measured with no influence from the insulation crimp.
2. The above specifications are guidelines to an optimum crimp.
Note:
A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,
insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,
destructive, pull force test should be preformed to check hand tool crimp. Pull Force value must exceed the
minimum pull force specifications listed.
CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage
can occur to the tool or die.
INSTALLATION
To install the Tool Kit into the Power Crimp Head follow the steps below:
Anvils and Punches Installation
1. Insert the Anvils into the bottom slots of the nest. Install the M4 x 10 long
BHCS and tighten in place.
2. Insert the Punches into the top slots of the nest. Install the M4 x 18 long
BHCS and tighten in place. See Figure 1.
Locator Installation and Removal
Follow the steps below to install or replace the locator. See Figure 2.
To install the locator
1. Position the locator with the hole over the brass pivot shaft and snap it into place.
To remove the locator
1. Open the crimp hand tool.
2. Swing the existing locator open and
away from the hand tool.
3. Firmly press down on the brass
pivot shaft with your thumb, while
pulling the locator up. Slip the
locator off the top of the brass pivot
shaft.
OPERATION
Open the tool by squeezing the handles
together, at the end of the closing
stroke, the ratchet mechanism will release the handles, and the hand tool will spring open.
Crimping Terminals
1. Select the desired terminal listed in the preceding charts. Make sure that the proper locator is mounted on the
tool.
Figure
LOCATOR
JAWS OPEN
TERMINAL
PUSH HERE
TO OPEN
WIRE STOP
SWING OPEN
LOCATOR
LOCATOR TERMINAL
IN PLACE
Figure 4

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 4 of 9
Revision: D Revision Date: 06-30-11
2. Swing the terminal locator away from the crimp tool shown in Figure
4. Some terminals with large insulation grips may interfere with the
crimp tooling when swinging the locator into position. The terminal
must then be loaded into the locator in the closed/crimp position.
3. When using the locator, press down on the wire stop on the locator
as shown in Figure 4. Insert the proper terminal into the proper nest
opening. Make sure when choosing the nest opening, it will
correspond with the A, B, or C profile on the hand tool.
4. Return the locator to its original position.
. Insert the proper wire over the terminal. Some large O.D. wires may
need to be placed into the terminal before closing the tool. Gently
touch the wire stop with the end of the wire. See Figure .
6. Compress the terminal by squeezing the tool handles until the
ratchet mechanism cycle has been completed. Release handles to
open the jaws.
7. Return the locator to its original position.
8. Insert the proper wire over the terminal. Some large O.D. wires may
need to be placed into the terminal before closing the tool. Gently
touch the wire stop with the end of the wire. See Figure .
9. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.
Release handles to open the jaws.
10. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on
the wire. The terminal locator can be in either position.
11. Visually inspect the crimped terminal for proper crimp location.
Note: The tamper proof ratchet action will not release the tool until it has been fully closed.
For the Battery Power Tool:
1. Cycle the Battery Power Tool to crimp the terminal to
the wire.
2. Remove the crimped terminal from the terminal locator
by pressing down on the wire stop and gently pulling
on the wire. The terminal locator can be in either
position.
3. Visually inspect the crimped terminal for proper crimp
location.
Locator Change Over and Replacement
Multiple styles of locators maybe provided with the crimp
hand tool. They are different colors for easy identification.
See the parts list on the last page of the document. Make
sure the desired style of locator is installed for the proper
terminal and wire. Follow the steps below to change the
locators.
1. Open the crimp hand tool.
2. Swing the existing locator open and away from the hand tool.
LOCATOR
IN PLACE
WIRE STOP
TERMINAL
WIRE AGAINST
STOP Figure 5
WIRE STOP
WIRE
SWING
LOCATOR
OPEN
PRESS DOWN ON
BRASS PIVOT SHAFT
LIFT UP LOCATOR
JAWS OPEN
Figure 6

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page of 9
Revision: D Revision Date: 06-30-11
3. Firmly press down on the brass pivot shaft
with your thumb, while pulling the locator up.
Slip the locator off the top of the brass pivot
shaft. See Figure 6.
4. Replace it with the desired locator by putting
over the brass pivot shaft and snapping it into
place.
Maintenance
It is recommended that each operator of the tool
be made aware of, and responsible for, the
following maintenance steps:
1. Remove dust, moisture, and other
contaminants with a clean brush, or soft, lint
free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine
oil. Do not oil excessively. The tool was engineered for durability but like any fine piece of equipment it needs
cleaning and lubrication for a maximum service life of trouble free crimping. Use a 30 weight automotive (light)
oil used at the oil points, every ,000 crimps or 3 months, shown in Figure 7A or 7B will significantly enhance
the tool life.
4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto
certain terminations may affect the electrical characteristics of an application.
. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,
and store the tool in a clean, dry area.
Miscrimps or Jams
Should this tool ever become stuck or jammed in a
partially closed position, Do Not force the handles
open or closed. The tool will open easily by
pressing the ratchet release lever. See Figure 8.
How to Adjust Tool Preload
(See Figure 8)
This hand tool is factory preset to 2 -4 LBS.
preload. It may be necessary over the life of the
tool to adjust tool handle preload force. Listed
below are the steps required to adjust the crimping
force of the hand tool to obtain proper crimp
conditions:
1. Remove or fold back the handle grip from the handle to expose the eccentric axle and setting wheel.
2. Remove the locking screw with a 2mm hex wrench. The wrench set (63810-0101), is not supplied. It is sold
separately from the hand tool.
3. Turn the eccentric axle and setting wheel with the wrench or pliers Counter-clockwise (CCW) to increase
handle force.
RATCHET
RELEASE LEVER
Figure 8
HANDLE
GRIP
REMOVED
ECCENTRIC AXLE
HANDLE
GRIP
LOCKING
SCREW
WRENCH SET
(SOLD
SEPERATELY)
PRELOAD
CHECK POINT
25.4MM
SETTING WHEEL
Figure 7B
LUBRICATION
POINTS
(BOTH SIDES)
LIGHT OIL
(EVERY MONTH
OR
5,000 CRIMPS)
Figure 7A

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 6 of 9
Revision: D Revision Date: 06-30-11
4. Replace the locking screw, aligning the nearest notch in the setting wheel to locking screw.
. Replace the handle grip.
6. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted.
Warranty
This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital
components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30
days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will
not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,
fixturing, or use of handle extensions voids this warranty.
CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.
CAUTIONS
1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for
production use. Repetitive use of this tool should be avoided.
2. Insulated rubber handles are not protection against electrical shock.
3. Wear eye protection at all times.
4. Use only the Molex terminals specified for crimping with this tool.
Certification
Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for
customers to re-certify hand tools.
% This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped
12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than
2 mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull
testing.
% If the tool does not meet minimum pull force values, handle preload should be increased and the pull test
rerun, (See How to Adjust Preload).
% When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and
replaced.
The chart below shows all applications for this Tool Kit.
Tool Kit
Order No.
Tool
Order no.
Tool
Description
Power Head
Order No.
Adapter
Description
Figure
No.
63811- 270
63810-0100 Hand Crimp Frame (Short) N/A N/A 9
63810-0400 Hand Crimp Frame (Long) N/A N/A 9
63816-0200 Battery Power Tool (110 V) 63816-0300 Power Crimp Head 10
63816-02 0 Battery Power Tool (220 V) 63816-0300 Power Crimp Head 10

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 7 of 9
Revision: D Revision Date: 06-30-11
Applications for the Tool Kit
Hand Crimp Tool Battery Powered Tool
Figure 9 Figure 10
WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper
instruction and without first reading and understanding the instructions in the proper Manual or
Specification Sheet. See Chart above for the correct Manual or Specification Sheet.
WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the
power is turned off.
CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.
CAUTION: Wear safety glasses when operating or serving this tool.
POWER
CRIMP
HEAD
LOCKING PINS
BATTERY
POWERED
TOOL
TOOLING KIT
HAND CRIMP
FRAME LONG
AND SHORT
TOOLING
KIT

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 8 of 9
Revision: D Revision Date: 06-30-11
RATCHET
RELEASE SCREW
Figure 11
1
M4 X 6mm
LONG BHCS
M4 X 12mm
LONG BHCS
5
7
WITH TOOL KIT
LOCATOR ONLY
M4 X 12mm
LONG BHCS
4
4
2
5
6
5 WITH TOOL KIT
LOCATOR ONLY
HAND TOOL PARTS LIST
Item Number Order Number Description Quantity
1 63810-0100 Hand Crimp Frame (Short) 1
2 63810-0101 Wrench Set (Not included) 0
3 63810-0102 Locator Base 1
4 63810-0103 Repair Kit (Not included) 0
63811- 270 Tool Kit with Locator 1
6 63811- 27 Locator #1-Black 1
7 63811- 276 Locator #2-Gray 1

Tool Kit for SPOX™ Crimp Terminals
Doc No: ATS-63811 2HM Release Date: 04-03-06 UNCONTROLLED COPY Page 9 of 9
Revision: D Revision Date: 06-30-11
Figure 12
1
2
2
M4 by 8 Long
BHCS
M4 by 18 Long
BHCS
M4 by 10 Long
BHCS
1
POWER HEAD PARTS LIST
Item Order No Engineering No. Description Quantity
1
63816-0300 63816-0300 Power Crimp Head 1
2
63811- 270 63811- 270 Tool Kit 1
http://www.molex.com