molex 63813-2100 User manual

63813-2100 Modular Card Extractor Tool
Doc No. 63813-2100 Release Date: 05-10--06 UNCONTROLLED COPY Page 1 of 5
Revision: A Revision Date: 05-10-06
Module Card Extractor Tool
Instruction Manual
Part No. 63813-2100
FEATURES
% This tool is designed for the removal of the memory module card from the metal latch 87814 series Molex sockets, 1mm pitch,
276-circuit vertical press-fit with metal latch DDR2.
SCOPE
Products: 87814 Series 276 Circuit Vertical Press-fit Metal Latch DDR2 Dimm Connector System. See Product List below for specific part
numbers.
Product List
The following is a partial list of the product order numbers and their specifications this tool is designed to run. Updates to this list are
available on www.molex.com.
Assembly Order Number Description
87814-1001
87814-1002
1.00mm (.039") Pitch DDR-2 DIMM Socket, Vertical,
Press-fit, 276 Circuits Metal Latch
DESCRIPTION
The 1mm pitch, 276-circuit vertical press-fit with metal latch DDR2
takes up a much smaller space inside the housing than a conventional
latch will. The entire connector length is almost similar to the module
card. However, the latch cannot be extracted by hand and this
extraction tool is required to withdrawal the module card from the
metal latch.
The Module Card Extractor Tool consists of modular card latch, metal
latch, and thumb pusher with a handle.
METAL LATCH PUSHER
Figure 1
THUMB PUSHER
MODULE CARD
LATCH
HANDLE

63813-2100 Modular Card Extractor Tool
Doc No. 63813-2100 Release Date: 05-10--06 UNCONTROLLED COPY Page 2 of 5
Revision: A Revision Date: 05-10-06
PCB BOARD
Figure 2
MODULE CARD
METAL
LATCH
PUSHER
METAL
LATCH
PUSHER MODULE HOUSING
MODULE CARD
LATCHES OPEN
METAL LATCH PUSHER
Figure 3
MODULE CARD
MODULE CARD
HOUSING
EXTRACTOR
TOOL
MODULE CARD
HOUSING
Figure 4
METAL LATCH
PUSHER
MODULE
CARD
MODULE CARD
LATCHES LOCKED
IN PLACE
LIFT UP BY
THE HANDLE
Operation
1. Align the metal latch pushers (2) with the slots on the module card housing. See Figure 2.
2. Push the extractor tool down and into the slots. The module card latches are spring-loaded and will open when extractor tool is
engaged in the module card housing. See Figure 3.
3. Make sure the extractor tool is firmly seated in the slots of the module card housing and the module card latches are locked into
the module card.
4. Pull the module card straight up with the handle of the extractor tool. See Figure 4.

63813-2100 Modular Card Extractor Tool
Doc No. 63813-2100 Release Date: 05-10--06 UNCONTROLLED COPY Page 3 of 5
Revision: A Revision Date: 05-10-06
Figure 5
MODULE CARD
MODULE CARD
LATCHES WILL
RELEASE
PUSH DOWN
ON THE THUMB
PUSHER
5. When the module card is free of the housing, press down on the thumb pusher. This will open the module card latches and release
the card from the extractor tool. See Figure 5.
Maintenance
It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps:
1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth.
2. Do not use any abrasive materials that could damage the tool.
3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil
excessively.
4. When tool is not in use, store in a clean, dry area.
CAUTION: Molex specifications are valid only when used with Molex terminals, applicators and tooling.

63813-2100 Modular Card Extractor Tool
Doc No. 63813-2100 Release Date: 05-10--06 UNCONTROLLED COPY Page 4 of 5
Revision: A Revision Date: 05-10-06
PARTS LIST
** Available from an industrial supply company such as MSC (1-800-645-7270).
Item Order No Description Quantity
63813-2100 Module Card Extractor Tool (Figure 6)
1 63813-2101 Extractor Base 1
2 63813-2102 Pusher Plate 1
3 63813-2103 Base Cover 1
4 63813-2204 Handle 1
5 63813-2205 Handle Shaft 1
6 63813-2206 Module Card Latch 2
7 63813-2207 Metal Latch Pusher 2
8 63600-2698 Knob 1
9 63600-2699 Metal Bushing 1
10 63600-2700 Compression Spring 1
11 63600-2701 Compression Spring 4
12 63600-2702 1.5mm Diameter Dowel Pin 2
13 63600-2703 M4 Screw Plug 4
14 63600-2704 M3 by 8 Long Low Head SHCS 2
15 N/A M2.5 by 10 Long SHCS **8
16 N/A M3 by 35 Long SHCS **2
17 N/A 4mm by 10 Long Dowel Pin **2

63813-2100 Modular Card Extractor Tool
Doc No. 63813-2100 Release Date: 05-10--06 UNCONTROLLED COPY Page 5 of 5
Revision: A Revision Date: 05-10-06
4
16
12
(2)
(2)
(8)
(2)
10
17
7
15 14
8
(2)
1
5
Figure 6
(4)
(2)
6 (2)
2 3
13
11 (4)
9
Assembly Drawing
Americas Headquarters
-JTMF*MMJOPJT64"
.0-&9
BNFSJOGP!NPMFYDPN
Far East North Headquarters
:BNBUP,BOBHBXB+BQBO

GFOJOGP!NPMFYDPN
Far East South Headquarters
+VSPOH4JOHBQPSF

GFTJOGP!NPMFYDPN
European Headquarters
.VOJDI(FSNBOZ

FVSJOGP!NPMFYDPN
Corporate Headquarters
8FMMJOHUPO$U
-JTMF*-64"

'BY
Visit our Web site at http://www.molex.com