Molift Smart 150 User manual

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 1 of 20

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 2 of 20
Table of content
About Molift Smart...............................3
Before using the patient lifter .................... 3
Explanation of symbols ............................. 3
General Safety precautions .................4
General ..................................................... 4
Lift and transfer ......................................... 4
Assembly / disassembly .......................5
Unpacking ................................................. 5
Assembly................................................... 5
Disassembly.............................................. 6
Storage...................................................... 6
Molift Smart 150 - use ..........................7
Checklist before use .............................7
Lift and transfer ....................................8
Use of spread legs .................................... 8
Safety devices .......................................9
Emergency stop and lowering................... 9
Operation ........................................... 10
Battery charger........................................ 10
Battery capacity....................................... 10
Electronics............................................... 10
Technical data .................................... 11
Labelling.................................................. 12
Accessories......................................... 13
Lifting sling .............................................. 13
Equipment.......................................... 14
Transport bag ......................................... 14
Troubleshooting ................................ 15
Maintenance ...................................... 16
Cleaning .................................................. 16
Monthly inspection .................................. 16
Periodic inspection .................................. 16
Service .................................................... 17
Checklist periodic inspection................... 18
CE declaration......................................... 19
IMPORTANT!
The patient lifter is only meant to be used by
qualied personnel.
The manual shall not be handed over, or
made available to, any unauthorised third
party, without a prior written consent from
Etac Supply Gjøvik. Existing laws, conventions
and agreements protects all documents. No
extract of this documentation can be re-
produced, used or transferred without pri-
or written consent from Etac Supply Gjø-
vik. Violation of these regulations may lead
to judicial repercussions and economic
responsibility. Industrial rights are reserved.
Etac Supply Gjøvik
Hadelandsveien 2
2816 Gjøvik, Norway
Teleph: ([phone] www.molift.com
Fax: [phone] [email protected]

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 3 of 20
About Molift Smart
Molift Smart 150 is a foldable mobile lifter intend-
ed for lifting and transferring personnel. The lifter
is made out of light materials, it has castors and a
battery. It is therefore ideal for mobile care units,
such as home care personnel who has a need for
lifting capabilities without xed or stationary lift-
ing devices present in every home.
The Molift Smart 150 with accessories as de-
scribed in this manual are CE marked according
to the Council Directive concerning medical de-
vices (93/42/EEC). The lifter is classied as medi-
cal equipment class 1, and tested and veried by
a third party, according to standards IEC 60601-1,
IEC 60601-1-2 and NS-EN ISO 10535:2006
Before using the patient lifter
Before using a patient lifter, the operator must be
trained accordingly. Practice lifting a colleague,
and be lifted by others. It is important not only to
know how to move another person using the lifter,
but also how it is to be lifted. Try out and practice
using all the relevant slings for the dierent types
of lifter and movement you may encounter. Before
lifting a person, you should explain the procedure.
When using the lifter, it’s also important to use the
correct sling and accessories according to:
• typeofdisability
• size
• weight
• typeofmovement
The lifter must be taken out of service imme-
diately, or not returned to service, if faults
and/or irregularities that may have influence
on the safety are discovered.
Explanation of symbols
This symbol is used to point out instructions
and information related to work place safety
where injury may occur if the information is
disregarded or ignored. Follow these instruc-
tions, be careful and attentive at all times.
This symbol indicates important information
regarding the use of the equipment. If not
taken into consideration, it may lead to dam-
age or functional defects to the lifter or other
equipment.
This symbol indicates important and useful
information. If taken into consideration, it
will help the operator of the lifter to work ef-
ficiently. It may help simplify routines and to
explain complicated facts.

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 4 of 20
General Safety precautions
General
Before putting a Molift Smart 150 into operation,
the operator must ensure that the lifter and acces-
sories are in good working order, especially with
regards to safety.
A Molift Smart 150 shall only be used when all
safety devices and equipment is in place and fully
operational.
The lifter must be taken out of service immediate-
ly, or not returned to service, if faults and/or irreg-
ularities that may have inuence on the safety are
discovered.
The lifter is designed for use in room tempera-
ture, +10 to +40 °C. This should be taken into
consideration when transporting the lifter,
and therefore keeping it in a temperate part
of the vehicle. Alternatively, the lifter must
rest in a temperate room until the equipment
has achieved proper working temperature.
The lifter has an expected lifetime of 10 years
or 30 000 lifts with max load (SWL), when all
recommended service is performed.
Injury to personnel or equipment may occur if
Molift Smart 150 is used in an incorrect manner
and if i.e:
• coversareremovedbyunauthorisedpersonnel
• usedincorrectly
• insucientmaintenance
• loadexceedsmaximumlimit.Themaximum
load stated in this manual and on the lifter is
the maximum load
• unauthorisedrepairofelectricaldevicesorca-
bles
Lift and transfer
The Molift Smart 150 has a Safe Working
Load on 150 kg, meaning that it is tested
and approved for lifting of patients up to 150
kg. Attempts to lift patients above SWL may
damage the lifter and lead to personal injury.
The patient lifter may tip over if used incor-
rectly! Ignorance of warnings and instruc-
tions may lead to personnel injury. Read in-
structions carefully before attempting to lift
anyone.
Pay close attention to your actions. Ensure
that all four loops of the sling are securely fas-
tened to avoid the user slipping or falling
Use the push handle to manoeuvre the lift, do
NOT attempt to manoeuvre the lift by push-
ing on the lifting arm, actuator or patient.
Torn, cut, frayed or broken slings can fail, re-
sulting in serious injury to the user. Use slings
in good condition only. Destroy and discard
old, unusable slings.
Molift slings shall ONLY be used to lift per-
sons. NEVER use the sling to lift and/or move
objects of any kind.
Molift Smart 150 should not be run constant-
ly for more than 2 minutes during 18 minutes.
If the lifting movement does not start when
the corresponding button is pressed, please
consult the fault finding table in the mainte-
nance chapter to locate the fault.
Several factors have to be considered during
movement of the lifter. Stand to the side of the
user when lifting. Ensure that arms and legs are
clear of the lift, chair, bed etc. Try to maintain eye
contact with the user - this will help the user feel
safe and comfortable.
Medical electrical equipment requires spe-
cial precautions regarding electromagnet-
ic compatibility (EMC) and must be installed
and used according to instructions con-
tained in this manual. Portable or mobile ra-
dio communication equipment may affect
the medical electrical equipment.

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 5 of 20
Assembly / disassembly
Unpacking
• Theliftercomesinonecardboardbox.Verify
that the box has no apparent damage. If dam-
aged, check the content and contact your deal-
er for assistance if components are damaged.
• TheboxcontainsonecompleteMoliftSmart
lifter with hand control, battery and battery
charger.
Assembly
The battery must not be in the battery holder
during assembly!
• Removethetransportelasticandspreadthe
legs to working position (maximum width).
The legs must be spread to working position
before the column can be mounted.
• Liftuptheliftingcolumnandslideitintothe
bracket on the chassis.
• Whenthecolumnhasplaceditselfinthebot-
tom of the bracket, it must be xed with the
locking handle on the back of the chassis. Push
the locking handle down (1) and make sure the
column is properly xed.
• Liftthesuspensionoutofthetransporthook.
Do not start to run the lifting arm before the
suspension is released!
• Insertthebatteryintothebatteryholderand
verify that the emergency stop button isn’t ac-
tivated.Runtheliftingarmupanddownwith-
out load to verify that it is working properly.
Check that the lifter is mounted correctly with
no loose part or damages. Ensure that the
lifting column is fixed properly, and that the
legs do not move inside working position.
Checklist after mounting.
• Checkthelifteraccordingtothechecklistbe-
fore use on page 7.
Transport position
Working position
The column must be
placed in the bottom of
the bracket on chassis as
shown on the illustration
to the left.
Max width

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 6 of 20
0°C
45°C
Molift Group AS,
Ole Deviksvei 44,
0668 Oslo
Norway
([phone]
www.molift.com
20 %
90 %
50 kPa
106 kPa
Labeling outside on every cartoon with Molift lifter or accessories/spare parts
Size on label ca 105x75 mm
Black printing directly on cartoon
Alternatively the labels can be printed on a A4 8 labels sheet (black printing on white bacground).
Note! Only page 2 for printing on sheet with 8 labels
Desctiption Dimension Material Comment
Designed/Drawn
I. Værnes
Date
14.11.07
Projection Scale
Drawing name
Label packing
Storage conditions Drawing
1
Size
A4
A Released for production 14.11.07 IV
Rev Description Date/Sign Approved
Disassembly
• Runtheliftingarmallthewaydownwhile
holding the suspension up towards the lifting
arm allowing the suspension to be placed into
the transport hook.
• Removethebatteryfromtheliftertopreventit
from falling out during transportation.
The control electronics are active as long as
the battery is placed in the holder. If the lifter
is to be stored for a longer period, the battery
should then be removed (or emergency stop
activated) to avoid unnecessary discharge of
the battery.
• Openthelockinghandle,liftuptheliftingcol-
umn (grab with both hands and lift straight up)
and fold the column down to transport posi-
tion.
The lifter can be split into two parts by lifting
the column from the chassis completely. The
lifting column/-arm and the chassis with legs
are then separate parts.
Be careful nottogetlegs/arms/handswedged
between the parts when folding down the
lifting column/-arm.
• Fastenthehandcontroltothedrivinghandle
• Pressthelegstogetherandsecurelegsandlift-
ing column/-arm with the transport elastic.
• Putthelifterintothebag.
Storage
Forlongtimestorageitisrecommendedthatthe
battery is removed and the emergency stop but-
ton is activated. Storage conditions should be be-
tween
Pressure: 50 - 106 kPa
Humidity: 20 - 90 %
Temperature: 0 - 45 °C

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 7 of 20
Push handle
Battery holder /
control electronics
Emergency stop
Lifting column
Battery
Suspension
Lifting motor
Adjustable legs
Lifting arm
Chassis with
lifting column
fixing bracket
BACK
FRONT (forwards direc-
tion of travel)
Molift Smart 150 - use
The Molift Smart 150 hand control has two but-
tons (up and down). In addition there is a diode
which gives a light if the battery needs charging.
The legs are adjusted with pedals on the chassis.
Checklist before use
1. Check that the lifter has no apparent damage
or other faults.
2. Check that there are no loose parts, and ensure
that the lifting column is properly xed and
that the locking handle is properly tightened.
3. Check that the legs
are moving in working
position only, mean-
ing that the legs do
not move inside work-
ing position with the
column mounted (see
g A).
4. Check that the suspen-
sion is released from
the transport hook.
5. Check that the emer-
gency stop button is
not activated and that the lifter is functioning.
6. Checkthatyouhavesucientlychargedbat-
teries (that the battery diode on hand control
or chassis does not light).
7. Check that the service lamp gives a green light.
If yellow or red light, send lifter to service.
8. If there are any faults or irregularities, the lift-
er should be taken out of service immediately
and marked “out of order”. Contact your service
partner or local Molift representative.
Emergency stop
Electrical emer-
gency lowering
Battery
Battery indicator
Fig A
Battery
indicator Up
Down

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 8 of 20
Lift and transfer
The suspension shall always be positioned across
the user as shown left in the illustration below.
Check that the sling is properly fastened to all
four hooks on the suspension to make sure
the patient is nor sliding or falling out
Try to position the user as low as possible (prefer-
ably resting the feet on the chassis) when transfer-
ring the lifter with a suspended user. In this way,
the centre of gravity will be as low as possible and
therefore reducing the risk of instability. The lifter
should be manoeuvred with spread legs in outer
position to achieve the highest possible stability.
Be careful during movement - the suspended user
may swing somewhat during turns, stops and
starts. Be particularly careful when manoeuvring
close to furniture to prevent the suspended user
from colliding with these objects.
The lifter shall not be used to lift or move us-
ers on sloping surfaces.
Avoid deep pile carpets, high thresholds, uneven
surfaces or other obstacles that may block the cas-
tors. The lifter may become unstable if forced over
such obstacles increasing the risk of tipping over.
The lifter shall only be used for movement
over short distances. It is not a replacement
for wheelchair or similar.
Use of spread legs
Use wide legs wherever appropriate, for instance
to position the lifter around wheelchairs, toilets
etc.
• Tospreadthelegs,press(pump)theleftpedal
on the chassis.
• Tonarrowthelegs,press(pump)theright
pedal.
On carpet floors you might find it difficult to
manoeuvre the legs with a patient in the lift-
er. It is recommended, if possible, to adjust
the legs before suspending the patient in the
lifter. Alternatively you might try to move the
lifter at the same time as pressing the pedals
for leg adjustment.
Right pedal,
legs in
Left pedal,
legs out

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 9 of 20
Safety devices
Molift Smart 150 is equipped with several safety
devices, which are intended to prevent damage to
personnel and equipment in the case of incorrect
use.
• Thelifterhasanoverloadsensorpreventing
the lifter to be operated with more the safe
working load, 150 kg. If the load exceeds the
SWL,thelifterwillstopthemovement.
• Thelifterhasasafetyfeaturetopreventthelift-
ingarmandsuspensionfromsqueezingauser
if lowered too much. The actuator will not pro-
duce any force in downward movements.
• Thelegsarefoldedtogetherduringtransport
to make the lifter as small as possible. When as-
sembling the lift, the legs must be spread to
working position. A safety feature will prevent
the lifting column to be xed in the bracket be-
fore the legs are spread beyond transport posi-
tion.
• Thesuspensionhassafetyhookstopreventthe
sling loops to fall o.
• Theelectronicsaredisabledifthetemperature
rises beyond a critical limit. Wait until the lifter
has cooled down before using it again.
Emergency stop and lowering
Contact your Molift service partner if the rea-
son for the failure causing an emergency low-
ering is unknown or if it is a result of failed
components or parts.
Emergency stop
The emergency stop will cut the power to the ac-
tuator, and is situated on the battery holder on the
lifting column. Turning it clockwise until it pops
out will reset the emergency button.
Electrical emergency lowering
It is possible to perform an emergency lowering of
the lifting arm in case of a general malfunction of
the control electronics. The button can be found
on the battery holder. If you need to perform an
emergency lowering, move the lifter to a suitable
location to lower the user.
• Presstheemergencyloweringbutton.Thelift-
ing arm will then perform a smooth downward
movement. The emergency stop button can
not be activated when performing electrical
emergency lowering.
• Ifthelifterstilldonotwork,changebattery
and try the emergency lowering procedure
again.
• Ifitstilldoesnotwork,thesuspendeduser
must be lifted out manually either by using the
manual lowering function or by requesting as-
sistance.
Manually emergency lowering
The manually lowering function on the actuator is
only to be used if the electrical lowering does not
work.
Pull the red handle slightly upwards. Take
care, the lifter moves faster when activat-
ing the handle more. The lifter will stop dead
with a danger of personal injury and damage
on the lifter if the handle is released suddenly.
Emergency
stop
Electrical
emergency
lowering
Manual
emergency
lowering

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 10 of 20
Operation
Battery charger
Molift Smart 150 is supplied with a battery with a
14,4Vcellunitthatisplacedinthebatteryhold-
er on the lift. A charger is also supplied to charge
the battery whenever needed. The charger can be
mounted on a wall surface or placed on a table.
Place the battery in the holder according to the
arrow markings. After a few seconds the charger
LEDwillchangefromyellowtoorange,indicating
thatthebatteryischarging.WhentheLEDgivesa
constant green light the battery is fully charged.
ThechargerLEDindicatethestatusofthebattery
as described below:
LED Mode
Yellow No battery
Yellow Initialization (10 sec)
Orange Fast charge
Green/yellow Top-off charge
Green Trickle charge
Orange/green Error
Battery capacity
The battery indicator on the hand control will il-
luminate if the voltage of the battery falls below
a certain level, indicating the need for charging.
There will also be an audible signal There is still
enough capacity to perform 3-5 lift cycles (75 kg)
at this point. The battery indicator on the battery
holder illuminates only if the handcontrol unit is
disconnected and the battery needs charging.
If the battery is discharged during a lift, it is
always enough power to lower the user down
again.
New batteries will not achieve full capac-
ity before it has been fully charged and dis-
charged a couple of times.
Electronics
There is a counter implemented in the electronic
system of the lifter, registering the number of lifts.
This number can be read by using the Molift Servi-
cetool, and a service lamp indicates when the lift-
er needs service consisting of exchange of the lift-
ing motor. See the chapter “Maintenance”.
The electronic system has a power save-function
which makes the system sleep after a while with
no activity. All lights will go out. Activate the sys-
tem by pushing one of the buttons on the hand
control.
If the lifter is run up and down constantly for a
longer period, the electronics may be overheated
and the lifter will stop. Wait until the lifter is cooled
down enough for further use.
Discarded lifters and batteries should be han-
dled as electronic waste and collected sepa-
rately according to local laws and regula-
tions.

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 11 of 20
Technical data
Weight, total:
Ex. battery; 25 kg / incl. battery: 25,8 kg
Material:
Steel and aluminium
Motor:
12 VDC
Battery:
14,4 V NiMH 2,2 Ah, Molift Power Pac
Battery charger:
Mascot type 2215, 10-22 cells NiCd/NiMH
Protection:
IPX4
Number of lifts with fully charged battery:
40 (75 kg/165 lb, 50 cm up/down)
Safe Working Load (SWL):
150 kg (330 lbs)
Lifting height:
0 - 750 mm below user
Lifting speed:
60 mm/sec
Sound level, max A-weighted sound power level:
LWA = 49,4 dB
Operating forces:
Buttons on hand control: 1,5 N
Foot pedal: max 300 N
Height of legs:
Max 110 mm
Turning diameter:
1300 mm
Measurement, transport:
1160 x 475 x 355 mm (LxWxH)
Measurement, assembled:
1160 x 1060 mm (LxW)
Measurements in illustrations below are in milli-
metres.
Measurements with lifter in working position
240
700

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 12 of 20
Measurements with lifter in transport position
Labelling
The main label is placed on the column bracket on
the left side of the chassis.
Control label on right side on chassis
Manufacturer
Read user
manual
Safe Working Load
For indoor
use
Model name
Part number and
year/week of
manufacturing
Serial number /
bar code
Nominal battery
voltage
Type B
Application
Separate waste
collection
Description Dimension Material Comment
Label 40x315 mm (Avery 740 pf) Part.no: 0920320
Designed/Drawn
IV
Date
20.11.08
Projection Scale
1:1
Drawing name
Label User Manual
Molift Smart Drawing
03-272
Size
A3
D Added MAX on fig 2 05.03.09 IV M H Lie
C Changed size added fig 18.02.09 IV M H Lie
B Changed size, illustrations 03.03.09 IV M H Lie
A Released for production 20.11.08 IV M H Lie
Rev Description Date/Sign Approved
For printing, use le “03-272 Label.eps”
Transparent background (Grey areas)
Color:
White background on illustrations
Red PMS 1797 (C=0%, M=100%, Y=100%, K=15%)
Grey PMS Cool Gray 2 (C=0%, M=0%, Y=0%, K=15%)
Black (C=0%, M=0%, Y=0%, K=100%)
Dimension 40x315 mm
CONTROL
1
2
3
5
6
MAX
4
Periodical in-
spection each 12
month
Control lifter ac-
cording to check-
list on page 18
Designated area
for calendar and
signed label for
periodical inspec-
tion
READ USER
MANUAL!
Molift Smart 150 short
guide for mounting
READ USER MANUAL!
Lifter in transport position
Spread legs
Raise the lifting column
Make sure the column is
placed correct in bottom
of the chassis
Close the locking handle
to secure the column.
Release the suspension
from transport hook.
Check lifter before use
(checklist on page 7)
Lifter is ready for use
Choose correct sling and
check for damage.
Make sure sling is at-
tached correctly. Pay
attention while lifting.

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 13 of 20
Accessories
Lifting sling
Molift Easy Paediatric Sling
Size No head support With head support
XXS Art. no 3005050 Art. no 3006050
XS Art. no 3005000 Art. no 3006000
Easy Toilet Sling and Basic Bathing Sling for kids,
seethetablesbelow,sizeXXSandXS.
Molift Easy Sling
Size No head support With head support
XS Art. no 3025000 Art. no 3026000
S Art. no 3025100 Art. no 3026100
M Art. no 3025200 Art. no 3026200
L Art. no 3025300 Art. no 3026300
XL Art. no 3025400 Art. no 3026400
XXL Art. no 3025500 Art. no 3026500
Molift Basic Sling
Size No head support With head support
XXS Art. no 3021050 Art. no 3022050
XS Art. no 3021000 Art. no 3022000
S Art. no 3021100 Art. no 3022100
M Art. no 3021200 Art. no 3022200
L Art. no 3021300 Art. no 3022300
XL Art. no 3021400 Art. no 3022400
XXL Art. no 3021500 Art. no 3022500
Molift Basic Bathing Sling
Size No head support With head support
XXS Art. no 3023050 Art. no 3024050
XS Art. no 3023000 Art. no 3024000
S Art. no 3023100 Art. no 3024100
M Art. no 3023200 Art. no 3024200
L Art. no 3023300 Art. no 3024300
XL Art. no 3023400 Art. no 3024400
XXL Art. no 3023500 Art. no 3024500
Molift Easy Toilet Sling
Size No head support With head support
XXS Art. no 3032050 Art. no 3033050
XS Art. no 3032000 Art. no 3033000
S Art. no 3032100 Art. no 3033100
M Art. no 3032200 Art. no 3033200
L Art. no 3032300 Art. no 3033300
XL Art. no 3032400 Art. no 3033400
XXL Art. no 3032500 Art. no 3033500
Molift Easy Toilet Sling Comfort
Size No head support Separate
head support
XXS Art. no 3016050 Art. no 3016055
XS Art. no 3016000 Art. no 3016001
S Art. no 3016100 Art. no 3016111
M Art. no 3016200 Art. no 3016222
L Art. no 3016300 Art. no 3016333
XL Art. no 3016400 Art. no 3016444
XXL Art. no 3016500 Art. no 3016555
Molift Easy Amputee Sling
Size No head support With head support
XXS Art. no 3027050 Art. no 3028050
XS Art. no 3027000 Art. no 3028000
S Art. no 3027100 Art. no 3028100
M Art. no 3027200 Art. no 3028200
L Art. no 3027300 Art. no 3028300
XL Art. no 3027400 Art. no 3028400
XXL Art. no 3027500 Art. no 3028500
Bag for slings - Art. no 3048000

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 14 of 20
Equipment
Transport bag
for Molift Smart 150 lifter w/batteries.
• Transportbag(soft)forMoliftSmart
Part. no: 3049175
• HardcaseforMoliftSmart
Part. no: 0920200
Sling size guide
Easy and Basic Slings
Size Color
code
Recomm.
weight
(Kg)
A
(cm)
B
(cm)
C
(cm)
XXL White 230-300 86 130 68
XL Blue 160-240 76 115 66
LGreen 90-160 66 100 64
MYellow 45-95 56 85 62
SRed 25-50 51 75 60
XS Light blue 17-25 46 65 58
XXS Pink 12-17 41 55 56
Choiceofslingsizedependsonbothuserweight
andshape/sizeofuser.
Please see the user manual that comes with
the sling for specific instructions.
A
BC

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 15 of 20
Troubleshooting
Faultsonliftersthatdonotfunctionastheyshould
after assembly (page 5) or after the pre-use check
hasbeencompleted(page7),canbelocalizedus-
ing the troubleshooting table below.
Symptom Possible cause/action
The lifting column
is wobbly
The lifting column is not correctly
positioned in the chassis or the
locking handle is not fully locked
/verify position of lifting col-
umn and locking handle acc. to
mounting instructions on page 5.
The lifting column can not be
correctly tted / faulty safety
mechanism in chassis, contact
local representative for service
The lifter moves
unevenly on a
plane surface
The castors move unevenly be-
cause of pile and dust / clean
castors as described on page
16.
Fault in the leg spreading mech-
anism / contact local representa-
tive for service.
The lifter only
moves in one di-
rection - either up
or down
Hand control has failed / test
with another hand control and
change if defective.
The control electronics has failed
/ contact local representative for
service and use manually emer-
gency lowering, where neces-
sary
The lifter runs out
of control
Short circuit between hand con-
trol and lifter / clean hand control
plug surfaced with alcohol to re-
move grease
Defective hand control / replace
hand control / contact local rep-
resentative for service
The control electronics has failed
/ contact local representative for
service
Symptom Possible cause/action
The lifting arm (lift-
ing motor) does
not move
Emergency stop button is acti-
vated / turn button clocwise to
reset emergency stop, see p. 9
Battery is empty / change to a
new battery or recharge battery,
see page 10
The control electronics of the lift-
er is overheated / Leave lifter to
cool down, see page 10
The lifter is overloaded / make
sure the load does not exceed
150 kg, see page 9
The hand control cable is un-
plugged / reconnect plug
Hand control has failed / replace
hand control / contact local rep-
resentative for service
Defective control electronics /
contact local representative for
service
Battery does not
recharge
Faulty battery / try another bat-
tery / replace battery
Faulty battery charger / try an-
other charger / contact local rep-
resentative for service
If you have access to more than one lifter, it may
be helpful to change parts across lifters to help
identifyanyfaults.Forinstance,ifyoususpectthe
fault to be inside the hand control, exchange the
hand control with at functional one from another
similar lifter to see if the problem is xed.
If you are not able to solve the fault or problems
by yourself using this manual, please contact lo-
cal authorised service representative. If you do
not know whom to contact locally, please contact
your dealer or Molift Group AS to get help.

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 16 of 20
Maintenance
Maintenance of the lifter consists of check be-
fore use, cleaning, inspection and service. Check
the lifter according to the checklist before use on
page 7, to reveal faults or errors. In regularly in-
spections of the lifter, which as a minimum should
be monthly inspections and annual (periodic) in-
spections.
Cleaning
Detergents must be pH-neutral. Do not use
solvents or strong liquids - this may damage
surfaces on the lifter. For disinfection when
needed; use isopropyl alcohol. Avoid abrasive
cleaning products.
• Cleansurfaceswithadampclothusinganap-
propriate detergent.
• Removehairandpilefromthecastorsandver-
ify that the castors rotates without abnormal
friction.
• Cleancontactandhandcontrolwithspiritor
similar to remove grease and dirt.
• Regularcleaningisrecommendedandshould
be implemented in the suitable cleaning rou-
tines.
Monthly inspection
Assemble the lifter before inspection.
• Checkthelifteraccordingtothechecklistbe-
fore use on page 7.
• Cleanthelifterasdescribedabove.
• Verifythatthecontactsofthehandcontroland
charger is rmly in place, and verify that the ca-
bles for the hand control, actuator and charger
are intact.
• Runthelifterupanddowntoverifythatitruns
normally and without any abnormal noise.
• Theliftermustbetakenoutofserviceimme-
diately and marked “Out of order”, or not taken
into service, if faults and/or irregularities are
discovered.
Periodic inspection
Molift recommends periodic inspection once a
year, alternatively more often if required by local
regulations. Use the checklist for periodic inspec-
tion on page 18.
Inspectionistobeperformedbyauthorizedper-
sonnel. The owner is responsible to ensure prop-
er logging and written verication of each inspec-
tion.

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 17 of 20
Service
MoliftSmart150hasaLEDonthebatteryholder
indicatingifthelifterneedsservice.TheLEDgives
a green light when the lifter is ready for use.
The electronics logs how much the lifter is being
used, and the load it is used with. After a given
time of usage there will be given a signal that the
lifterneedsservicetotheserviceLED.TheLEDwill
rst give a yellow light, then red. Take contact with
your local service representative and order serv-
ice. If there is a sound together with the light, it
means the lifter needs service immediately.
Service lamp Status
No light Power save
Green Ready for use
Yellow Order service, lifter still
works
Red Perform service
Red + sound Perform service imme-
diately
Service consists of replacing the lifting motor and
check/replacement of worn or damaged parts.
Service and repair should be performed by au-
thorizedpersonnelonly.
Fillinandsignacopyofthechecklistonnextpage.
The owner is responsible to ensure proper logging
and written verication of each service or repair.
Battery
indicator
Service
lampe
Electrical
emergency
lowering

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 18 of 20
Checklist periodic inspection
28.04.2010
Lifter serial no.: ............................. .................................Other ID. no. (if any): .....................................................
Client:............................................. ................................. ..................... ..................................................................
Inspection carried out by: (Block capitals) ...................... ............. from..................................................................
Molift certification no. (if any) of inspector/repairer: ..... ..................... ..................................................................
The equipment has been tested and is in full working order
Yes
No
Place: .................................... Date: ................ Signature: ..................... ..................................................................
Checklist for periodic inspection of Molift Smart 150
Revision F –06/2009
COMPULSORY SAFETY CHECK (annual):
OK Fault Corrected Visual inspection
Whole lifter checked for damage, cracks and deformation and found to
be in good order. (Especially suspension, lifting arm, lifting motor,
wheels and all cables).
Lifter has been correctly assembled and no parts are missing.
(Especially column lock, column attachment and suspension).
All labels are present, without damage and readable
Accessories have been checked. See separate form for sling. Battery
charger is an accessory.
List the accessories checked: …………………………………………
Function checks
Emergency stop and hand control have been checked and are in working
order.
The lifter has been rolled over the floor (preferably under load) and runs
easily and steadily.
Leg extender mechanism functions correctly (stops in correct positions).
The lifter has been fully raised and lowered (preferably under load) and
moves evenly, without noise and the lifting motor shows no runout.
Servicing required
Servicing unnecessary because the servicing lamp is on green and the
lifter is under 5 years old.
Completed Compulsory in case of faults under one of the above points:
The lifter has been removed from service and clearly marked "OUT OF ORDER".
Certified personnel have been summoned to carry out repairs and servicing.
Name /Tel./ Fax:…………………………………………………………………………
Completed Compulsory where lifter has been checked and approved:
The lifter has passed the safety check and been affixed with the Molift safety check label,
duly dated and signed.
The ticked and signed checklist has been passed to the client.
Comments on faults and repairs:............................. .................... ............................................................
................................................... ............................. .................... ............................................................
................................................... ............................. .................... ............................................................
................................................... ............................. .................... ............................................................
................................................... ............................. .................... ............................................................
................................................... ............................. .................... ............................................................

BM09201 Molift SMART 150 English - Rev C1/08/10 Page 19 of 20
CE declaration
DECLARATION OF CONFORMITY
Etac Supply Gjøvik
Hadelandsveien 2
2816 Gjøvik
NORWAY
Telephone: + 47 4000 1004
hereby declare that:
Molift SMART 150 patient lifter
and that the accessoires used only together with this product
are in conformity with:
• The Council Directive concerning medical devices 93/42/EEC (incl amendment 2007/47/EC)
and according to this classied as medical equipment class 1
Expiration date : 11th October 2016
Molift SMART is manufactured in conformity with the following national or
international standards that also might implement a harmonised standard:
• ISO10535:2006 Hoists for the transfer of disabled persons - Requirements and test methods
• ISO 14971 Medical equipment - Risik analysis
Notied body:
Hjelpemiddelinstituttet NEMKO AS
Gregersensvej Gaustadalleen 30
DK-2630 Taastrup N-0314 OSLO
Denmark Norway
Tel: + 45 43993322 Tel: + 47 22960342
Title: Chief Operating Ofcer
Name: Morten Harald Lie
Company: Etac Supply Gjøvik
11.10.2011
Date Signature

Norway
Etac AS
PB 249
1501 Moss
Tlf: ([phone]
Fax: [phone]
www.etac.no
Australia
Patient Handling Australia
8 Chapel Street
Marrickville
NSW 2204 Sydney
www.patienthandling.com.au
Ceiling Hoist Solutions
Melbourne Oce
58-62 Star Crescent
AU-3803 Hallam, VIC
www.ceilinghoistsolutions.com.au
Austria
Paul Bständig GesmbH
Strohbogasse 8
1210 Wien
Tel. [phone]
Fax [phone]
www.bstaendig.at
Belgium
Pronk ergo NV
Sint-Pietersmolenstraat 204/1
8000 Brugge
T +32 (0)50/32 20 20
F +32 (0)50/32 20 40
www.pronkergo.be
Danmark
Etac A/S
Egeskovvej 12
8700 Horsens
Tel. [phone]
www.etac.dk
Finland
Mediq Suomi Oy
Koskelonkuja 4
FI-02920 Espoo
Tel.: [phone]
Fax: [phone]
www.mediq./apuvaline
France
Praxis Medical Technologies
Parc 2000
107, rue Dassin
34080 Montpellier FRANCE
Phone +(33) 04 99 77 23 23
Fax +(33) 04 99 77 23 39
[e-mail]
Germany
Herrmann & Co GmbH
Oelder str. 20
33378 Rheda-Wiedenbrück
Tel: 05242 / 9671 40
Fax: 05242 / 9671 41
www.herrmann-co.de
Iceland
Eirberg
Storhofoi 25
IS-110 Reykjavik
www.eirberg.is
Ireland
Meditec Medical Ltd.
Unit 28, Whitestown Drive
Whitestown Industrial Estate
Tallaght, Dublin 24
Tel: [phone]
www.meditecmedical.ie
Israel
Mediscan Systems Ltd
P.B Box 2195
6 Hamanov St.
Rehovot 76386
IL-76121 Rehovot
www.mediscan.co.il
Italy
Fumagalli
Piazza Puecher 2
22037 Pontelambro
Tel [phone]
Fax [phone]
www.fumagalli.org
Japan
Pacic Supply Co. Ltd
1-12-1 Goryo, Daito-shi
JP-5740064
www.p-supply.co.jp
Netherlands
Pronk Ergo bv
Cobaltstraat 14
2718 RM Zoetermeer
Tlf: 079-361 13 40
Fax: [phone]
www.pronkergo.nl
New Zealand
Morton & Perry
Homecare Equipment
P.O. Box 34439
Birkenhead
Auckland 0746
www.mortonperry.co.nz
Spain
Karinter S.L
C/Ramón Turró, 5-9 Local 4
08005 Barcelona
Tel. [phone]
Fax. [phone]
www.karinter.com
Sverige
Etac Sverige AB
P. O. Box 203
SE - 334 24 Anderstorp
Tel: +46 - 371-58 73 00
Fax: +46 - 370-48 73 90
www.etac.com
Switzerland
Kuhn und Bieri AG
Sägestrasse 75
3098 Köniz
Tel. [phone]
Fax [phone]
www.kuhnbieri.ch
United Kingdom
Meditec Molift Ltd
Hi Trac House
Unit 1 Woodrow Business Centre
Woodrow Way, Irlam
Manchester M44 6NN
Tel. [phone]
Fax [phone]
www.molift.com
USA
Molift Inc.
8406 Benjamin Road
Suite C
Tampa, FL 33634
Tel. [phone]
Fax [phone]
www.moliftinc.com