Monogram ZV48SSJSS User manual

INSTALLATION
INSTRUCTIONS
30”, 36” and 48”
Professional Vent Hood
MONOGRAM.COM

231-2000859 Rev. 0
Safety Information
READ AND SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
ŶIMPORTANT— Save these instructions
for local inspector’s use.
ŶIMPORTANT— Observe all governing
codes and ordinances.
ŶNote to Installer — Be sure to leave these
instructions with the Consumer.
ŶNote to Consumer — Keep these instructions with
your Owner’s Manual for future reference.
ŶSkill Level — Installation of this appliance requires
basic mechanical and electrical skills.
ŶCompletion Time — 1 to 3 Hours.
Ŷ3URSHULQVWDOODWLRQLVWKHUHVSRQVLELOLW\RIWKHLQVWDOOHU
3URGXFWIDLOXUHGXHWRLPSURSHULQVWDOODWLRQLVQRW
covered under the warranty.
Ŷ)RU0RQRJUDPORFDOVHUYLFHLQ\RXUDUHDYLVLW
monogram.com or call 1.800.444.1845.
Ŷ)RU0RQRJUDPVHUYLFHLQ&DQDGDYLVLWmonogram.ca
or call 1.800.561.3344.
Ŷ)RU0RQRJUDP3DUWVDQG$FFHVVRULHVYLVLW
monogram.com/use-and-care/parts or call
1.800.444.1845..
CAUTION Due to the weight and size of these
vent hoods and to reduce the risk of personal injury
RUGDPDJHWRWKHSURGXFW TWO PEOPLE ARE
REQUIRED FOR PROPER INSTALLATION.
WARNING To reduce the risk of fire or electrical
VKRFNGRQRWXVHWKLVUDQJHKRRGZLWKDQ\H[WHUQDO
VROLGVWDWHVSHHGFRQWUROGHYLFH$Q\VXFKDOWHUDWLRQ
from original factory wiring could result in damage to
the unit and/or create an electrical safety hazard.
WARNING 725('8&(7+(5,6.2)),5(
(/(&75,&$/6+2&.25,1-85<723(56216
2%6(59(7+()2//2:,1*
• Installation work and electrical wiring must be done
by a qualified person(s) in accordance with all
DSSOLFDEOHFRGHVDQGVWDQGDUGVLQFOXGLQJILUHUDWHG
construction.
• Sufficient air is needed for proper combustion and
H[KDXVWLQJRIJDVHVWKURXJKWKHIOXHFKLPQH\RI
fuel burning equipment to prevent back drafting.
)ROORZWKHKHDWLQJHTXLSPHQWPDQXIDFWXUHU¶V
guidelines and safety standards such as those
SXEOLVKHGE\WKH1DWLRQDO)LUH3URWHFWLRQ$VVRFLDWLRQ
1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ
5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV
$6+5$(DQGWKHORFDOFRGHDXWKRULWLHV
 :KHQFXWWLQJRUGULOOLQJLQWRZDOORUFHLOLQJGRQRW
damage electrical wiring and other hidden utilities.
• Ducted fans must always be vented to the outdoors.
CAUTION To reduce risk of fire and to properly
H[KDXVWDLUEHVXUHWRGXFWDLURXWVLGH²GRQRWYHQW
H[KDXVWDLULQWRVSDFHVZLWKLQZDOOVRUFHLOLQJVRULQWR
DWWLFVFUDZOVSDFHVRUJDUDJHV

31-2000859 Rev. 0 3
Consignes de sécurité
AVANT DE COMMENCER
Veuillez lire attentivement ces instructions dans leur
intégralité.
ŶIMPORTANT— Veuillez conserver ces
instructions pour afin que l’inspecteur local puisse s’y référer.
ŶIMPORTANT— Respectez tous les codes
réglementaires et les règlements.
ŶNote destinée à l’installateur²$VVXUH]YRXVGHODLVVHU
ces instructions au client.
ŶNote destinée au client — Veuillez conserver ces
instructions avec votre manuel utilisateur afin de pouvoir
vous y référer ultérieurement.
ŶNiveau de compétence — l’installation de cet appareil
requiert des compétences en matière de mécanique et
d’électricité.
ŶDurée d’assemblage — 1 à 3 heures.
Ŷ/¶LQVWDOODWLRQLQFRPEHjO¶LQVWDOODWHXU6LOHSURGXLWFRQQDvW
XQHGpIDLOODQFHGXHjXQHLQVWDOODWLRQLQDSSURSULpHOD
garantie ne s’applique pas.
Ŷ3RXUOHVHUYLFHORFDO0RQRJUDPGDQVYRWUHUpJLRQYLVLWH]
monogram.com ou appelez le 1.800.444.1845.
Ŷ3RXUOHVHUYLFH0RQRJUDPDX&DQDGDYLVLWH]
monogram.ca ou appelez le 1.800.561.3344.
Ŷ3RXUOHVSLqFHVHWDFFHVVRLUHV0RQRJUDPYLVLWH]
monogram.com/use-and-care/parts ou appelez le
1.800.444.1845.
ATTENTION À cause du poids et de la taille de
ces hottes et pour reduire le risque de blessures et de
GRPPDJHV IL FAUT DEUX PERSONNES POUR FAIRE
L’INSTALLATION CORRECTEMENT.
AVERTISSEMENT
3RXUUpGXLUHOHULVTXHG¶LQFHQGLH
RXGHFKRFpOHFWULTXHLOQHIDXWSDVXWLOLVHUFHWWHKRWWH
DYHFXQUpJXODWHXUGHYLWHVVHpOHFWURQLTXHH[WHUQH7RXWH
modification de ce type du branchement d’usine peute
endommager l’appareil ou créer un risque de choc électrique.
AFIN DE RÉDUIRE LE RISQUE D’INCENDIE, N’UTILISEZ
QUE DES CONDUITS MÉTALLIQUES.
AVERTISSEMENT
$),1'(5e'8,5(/(5,648(
'¶,1&(1',(/(6e/(&752&87,21628/(6%/(6685(6
$8;3(56211(69(8,//(=5(63(&7(5&(48,68,7
• L’installation et le câblage électrique doivent être effectués
SDUXQHRXSOXVLHXUVSHUVRQQHVTXDOLILpHVFRQIRUPpPHQW
jWRXVOHVFRGHVHWWRXWHVOHVQRUPHVDSSOLFDEOHVGRQW
FHX[FRQFHUQDQWODUpVLVWDQFHDXIHXGHVFRQVWUXFWLRQV
• Une quantité d’air suffisante est nécessaire à une
combustion et une évacuation appropriées des gaz par
le conduit d’évacuation (cheminée) de l’équipement à
combustible pour éviter tout refoulement. Suivez les
directives et normes de sécurité du fabricant de l’appareil
FKDXIIDQWFRPPHFHOOHVSXEOLpHVSDUOD1DWLRQDO
)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$SDUO¶$PHULFDQ
6RFLHW\IRU+HDWLQJ5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ
(QJLQHHUV$6+5$(HWSDUOHVDXWRULWpVORFDOHV/HFDV
pFKpDQWLQVWDOOH]XQV\VWqPHGHFRPSHQVDWLRQG¶DLU
UHPSODFHPHQWFRQIRUPpPHQWDX[FRQGLWLRQVGHVFRGHV
ORFDX[GXEkWLPHQW
• Lorsque vous effectuez des découpes ou que vous percez
XQPXURXXQSODIRQGQ¶HQGRPPDJH]SDVOHFkEODJH
électrique ou tout autre réseau d’alimentation caché.
• L’air des ventilateurs disposant de conduits d’aération doit
WRXMRXUVrWUHpYDFXpYHUVO¶H[WpULHXU
ATTENTION Il faut prendre soin d’installer un conduit
YHUVO¶H[WpULHXUSRXUUpGXLUHOHULVTXHG¶LQFHQGLHHWSRXYRLU
évacuer l’air correctement. Il ne faut pas évacuer l’air dans
O¶HVSDFHHQWUHOHVSDURLVG¶XQPXUXQSODIRQGRXXQJUHQLHU
un espace sanitaire ou un garage.

431-2000859 Rev. 0
Información sobre Seguridad
LEA Y GUARDE ESTAS INSTRUCCIONES
ANTES DE COMENZAR
Lea estas instrucciones en su totalidad y
atentamente.
ŶIMPORTANTE —Conserve estas instrucciones
para uso del inspector local.
ŶIMPORTANTE— Cumpla con todos los
códigos y ordenanzas gubernamentales.
ŶNota para el Instalador —$VHJ~UHVHGHTXHHO
Comprador conserve estas instrucciones.
ŶNota para el Consumidor — *XDUGHHVWDVLQVWUXFFLRQHV
FRQVX0DQXDOGHO3URSLHWDULRSDUDUHIHUHQFLDIXWXUD
ŶNivel de habilidad — La instalación de este
electrodoméstico requiere un nivel básico de habilidades
mecánicas y eléctricas.
ŶTiempo de instalación — 1 a 3 horas.
Ŷ/DFRUUHFWDLQVWDODFLyQGHOSURGXFWRHVUHVSRQVDELOLGDG
del instalador. Si se producen fallas en el producto debido
DXQDLQVWDODFLyQLQDGHFXDGDODJDUDQWtDQRFXEULUiODV
mismas.
Ŷ3DUDDFFHGHUDOVHUYLFLRORFDOGH0RQRJUDPHQVXiUHD
visite monogram.com o llame al 1.800.444.1845.
Ŷ3DUDDFFHGHUDOVHUYLFLRGH0RQRJUDPHQ&DQDGiYLVLWH
monogram.ca o llame al 1.800.561.3344.
Ŷ3DUDDFFHGHUDODVHFFLyQGH3LH]DV\$FFHVRULRVGH
0RQRJUDPYLVLWHmonogram.com/use-and-care/parts o
llame al 1.800.444.1845.
PRECAUCIÓN Debido al peso y tamaño
GHHVWDVFDPSDQDVGHYHQWLODFLyQ\DILQGH
reducir el riesgo de lesiones personales o daños
sobre el producto—SE DEBERÁ CONTAR CON
DOS PERSONAS PARA UNA INSTALACIÓN
ADECUADA.
ADVERTENCIA $ILQGHUHGXFLUHOULHVJR
GHLQFHQGLRVRGHVFDUJDVHOpFWULFDVQRXVHHVWD
FDPSDQDGHFRFLQDFRQQLQJ~QGLVSRVLWLYRH[WHUQR
de control de velocidad de estado sólido. Cualquier
alteración del cableado original de fábrica podrá
producir daños en la unidad y/o crear un riesgo sobre
la seguridad eléctrica.
ADVERTENCIA $),1'(5('8&,5
(/5,(6*2'(,1&(1',26'(6&$5*$6
(/e&75,&$62/(6,21(662%5(3(5621$6
&803/$&21/26,*8,(17(
Ŷ(OWUDEDMRGHLQVWDODFLyQ\HOFDEOHDGRHOpFWULFR
deberán ser realizados por una persona(s)
FDOLILFDGDGHDFXHUGRFRQWRGRVORVFyGLJRV\
HVWiQGDUHVDSOLFDEOHVLQFOX\HQGRFRQVWUXFFLRQHV
resistentes a incendios.
Ŷ6HQHFHVLWDUiVXILFLHQWHDLUHSDUDXQDFRPEXVWLyQ\
VDOLGDGHJDVHVDGHFXDGDVDWUDYpVGHOFRQGXFWR
de humo (chimenea) del equipamiento de consumo
GHFRPEXVWLEOHSDUDHYLWDUODH[SORVLyQGHJDVHV
de humo con efecto reverso. Siga las pautas y
estándares de seguridad del fabricante del equipo
GHFDOHIDFFLyQWDOFRPRDTXHOORVSXEOLFDGRVSRU
OD1DWLRQDO)LUH3URWHFWLRQ$VVRFLDWLRQ$VRFLDFLyQ
1DFLRQDOGH3URWHFFLyQFRQWUD,QFHQGLRV1)3$
OD$PHULFDQ6RFLHW\IRU+HDWLQJ6RFLHGDG
(VWDGRXQLGHQVHGH&DOHIDFFLyQ5HIULJHUDWLRQ
DQG$LU&RQGLWLRQLQJ(QJLQHHUV,QJHQLHURV
GH5HIULJHUDFLyQ\$FRQGLFLRQDGRUHVGH$LUH
$6+5$(\ODVDXWRULGDGHVDFDUJRGHORVFyGLJRV
ORFDOHV&XDQGRFRUUHVSRQGDLQVWDOHXQVLVWHPD
de reposición (reemplazo) de aire de acuerdo con
los requisitos del código local de construcción.
3DUDDFFHGHUDVROXFLRQHVGHUHSRVLFLyQGHDLUH
GLVSRQLEOHVYLVLWH*($SSOLDQFHVFRP
Ŷ$OFRUWDURSHUIRUDUVREUHSDUHGHVRFLHORUUDVRV
no dañe el cableado eléctrico y otros conductos de
servicios ocultos.
Ŷ/RVVLVWHPDVGHFRQGXFWRVVLHPSUHGHEHUiQSRVHHU
YHQWLODFLyQKDFLDHOH[WHULRU
PRECAUCIÓN $ILQGHUHGXFLUULHVJRVGH
LQFHQGLR\GHFRQWDUFRQODVDOLGDGHDLUHDGHFXDGD
DVHJ~UHVHGHFRQGXFLUHODLUHKDFLDHOH[WHULRU±QR
ventile el aire de salida hacia espacios dentro de
SDUHGHVRFLHORUUDVRVRiWLFRViUHDVGHYHQWLODFLyQR
garajes.

31-2000859 Rev. 0 5
Design Information
CONTENTS
3URGXFW'LPHQVLRQV
3URGXFW'LPHQVLRQV
.....................................................
.....................................................
3
3DUWV3URYLGHG
3DUWV3URYLGHG
..............................................................
..............................................................
4
+DUGZDUH3DFNDJH
+DUGZDUH3DFNDJH
.......................................................
.......................................................
4
Tools and Materials Required
Tools and Materials Required
......................................
......................................
5
Installation Clearances
Installation Clearances
.................................................
.................................................
6
2SWLRQDO'XFW&RYHU$FFHVVRULHV
2SWLRQDO'XFW&RYHU$FFHVVRULHV
................................
................................
6
'HWHUPLQH,QVWDOODWLRQ+HLJKW'XFW&RYHU$FFHVVRULHV
'HWHUPLQH,QVWDOODWLRQ+HLJKW'XFW&RYHU$FFHVVRULHV
7
7
$GYDQFH3ODQQLQJ
$GYDQFH3ODQQLQJ
........................................................
........................................................
8
3RZHU6XSSO\
3RZHU6XSSO\
...............................................................
...............................................................
8
6WHS'HWHUPLQH'XFWZRUNDQG:LULQJ/RFDWLRQV
6WHS'HWHUPLQH'XFWZRUNDQG:LULQJ/RFDWLRQV
.....
.....
9
6WHS$,QVWDOO+RRG2QWR:DOO
6WHS$,QVWDOO+RRG2QWR:DOO
................................
................................
12
12
6WHS%,QVWDOO+RRG7R6RIILW2U%HQHDWK&DELQHWV
6WHS%,QVWDOO+RRG7R6RIILW2U%HQHDWK&DELQHWV
11
11
6WHS&RQQHFW'XFWZRUN
6WHS&RQQHFW'XFWZRUN
.........................................
.........................................
12
12
6WHS&RQQHFW(OHFWULFDO
6WHS&RQQHFW(OHFWULFDO
..........................................
..........................................
12
12
6WHS,QVWDOO'XFW&RYHUV
6WHS,QVWDOO'XFW&RYHUV
.........................................
.........................................
12
12
6WHS,QVWDOO)LOWHUV
6WHS,QVWDOO)LOWHUV
...................................................
...................................................
13
13
6WHS,QVWDOO,PSOHPHQW5RGV
6WHS,QVWDOO,PSOHPHQW5RGV
..................................
..................................13
PRODUCT DIMENSIONS
Model ZV48S With Straight Sides
Model ZV36S With Straight Sides
Model ZV30S With Straight Sides
Model ZV48T With Tapered Sides
Model ZV36T With Tapered Sides
Model ZV30T With Tapered Sides
18"
47-15/16"
47-15/16"
12"
25"
18"
35-15/16"
35-15/16"
12"
25"
18"
29-15/16"
29-15/16"
12"
25"
18"
28"
25" 35-15/16"
12"
18"
22"
25" 29-15/16"
12"
18"
40"
25" 47-15/16"
12"

631-2000859 Rev. 0
Installation Preparation
PARTS PROVIDED
Locate the parts packed with the hood.
2 Stainless Steel Grease Filters
(3 filters with 48" models)
Allen Wrench
For Implement Rods
2 Grease Filter Trays
(3 supports with 48" models.)
2 Implement Rods, 4 Allen Screws
and 4 Stand-offs
Heat Lamp
(2 with 48" models)
Monogram Logo
Nameplate
2 Knobs
HARDWARE
PACKAGE
Locate and check
contents. Screws
shown actual size.
6 Phillips head screws to
secure hood to the wood
support: (2 secured to
wood support)
2 (3/16") hollow wall
anchors with screws to
secure hood to the wall
at the bottom
6 screws to secure the
wood support and the
hood to the wall
2 flat washers
for wall anchors
Wood Support
with Original Screws

31-2000859 Rev. 0 7
Installation Preparation
CAUTION Lift the hood by grasping
the outside edges of the inlet opening of the hood.
Do not lift the hood by grasping the exhaust opening
or transition duct with damper!
PRECAUCIÓN Soulevez la hotte en agrippant
OHVERUGVH[WpULHXUVGHVRQRULILFHG¶HQWUpHNe soulevez
pas la hotte en agrippant l’orifice d’évacuation ou le
conduit de transition avec le registre!
ADVERTENCIA Levante la campana tomando los
H[WUHPRVH[WHULRUHVGHODDEHUWXUDGHODHQWUDGDGHOD
campana. ¡No levante la campana tomando la abertura
de la salida de aire o el conducto de transición con el
regulador!
• Open the carton and remove the hood and packaging.
• Confirm that all hardware and parts are present by
UHYLHZLQJWKHVHFWLRQQDPHG3DUWV3URYLGHGLQWKH
Installation Instructions.
• Loosen the screws holding the wood support to the back
of the hood. Remove wood support. Keep wood support
and screws. These will be used to mount the hood to the
wall.
)XOO\LQVSHFWDQGFRQILUPWKDWDOOWDSHDQGSDFNLQJ
material has been removed from the hood and transition
duct with damper
TOOLS AND MATERIALS REQUIRED
(NOT SUPPLIED)
3HQFLODQGWDSHPHDVXUH
3OLHUV
Electric or battery operated
GULOODQGELWV
9+]RU$PS
ZLUHZLWKJURXQG3URSHUO\
grounded branch circuit.
Key Hole Saw
Hammer
:LUHFXWWHU
stripper
Step ladder
Metal Snips Saber saw
or Sawsall
:LUHQXWV
3KLOOLSVDQGIODW
blade screwdrivers
Strain relief for
junction cover.
Spirit level
)ODVKOLJKW
Safety glasses
10" round metal
GXFWOHQJWKWR
suit installation.
Duct tape
Top view of open shipping carton
Do not lift from transition duct Hood
Lift hood out of
carton from the sides
Carton

831-2000859 Rev. 0
Advance Planning
INSTALLATION CLEARANCES
These vent hoods are designed to be installed onto a
wall or beneath a soffit or cabinet.
,QVWDOOWKHVHKRRGV´0LQWR´0D[DERYHWKH
cooking surface.
In this installation the ductwork running from the top
of the hood will be concealed in the soffit or upper
cabinetry.
)RUWKLVLQVWDOODWLRQDGHFRUDWLYHGXFWFRYHULV
available to conceal the ductwork running from the
top of the hood. Use of the duct cover requires
special consideration to the installation height above
the countertop.
NOTE: Clearances may vary due to type of cooking
product and local codes. Check with local inspectors
to be sure standard is applicable.
SOFFIT
Soffit Installation
30" MIN.
36" MAX.
Wall Mount Installation
30" MIN.
36" MAX.
OPTIONAL DUCT COVER
ACCESSORIES
Standard decorative duct covers are available in
´DQG´KHLJKWV'XFWFRYHUVPD\EHVWDFNHG
LQYDULRXVFRPELQDWLRQVWRFRQFHDOWKHGXFWZRUN
running from the top of the hood to the ceiling.
%HIRUH\RXEHJLQ\RXVKRXOGGHWHUPLQHWKH
installation height of the hood and order the
correct size duct cover. The duct covers should
be ordered at the same time as the vent hood and
be on site before installation. Order the duct cover
corresponding to your model.
6" Duct Cover
12" Duct Cover
Standard Duct
Covers
6" Duct Covers
Hood Model 6” Duct Cover Dimensions
ZV48T, ZV48S ZX48DC6J 6"H x 19-11/16"W x
11-7/8"D
ZV36T, ZV36S ZX36DC6J 6"H x 15-3/4"W x
11-7/8"D
ZV30T, ZV30S ZX36DC6J 6"H x 15-3/4"W x
11-7/8"D
12" Duct Covers
Hood Model 12” Duct
Cover Dimensions
ZV48T, ZV48S ZX48DC12J 12"H x 19-11/16"W
x 11-7/8"D
ZV36T, ZV36S ZX36DC12J 12"H x 15-3/4"W x
11-7/8"D
ZV30T, ZV30S ZX36DC12J 12"H x 15-3/4"W x
11-7/8"D

31-2000859 Rev. 0 9
Advance Planning
DETERMINE INSTALLATION HEIGHT, DUCT COVER ACCESSORIES
These vent hoods must be installed 30” min. to 36”
PD[DERYHWKHVWDQGDUG´KLJKFRRNLQJVXUIDFHZKHQ
installed over any professional style
UDQJHWRSRUUDQJH7KHH[DFWKRRGLQVWDOODWLRQKHLJKWLV
determined by the ceiling height.
1.0HDVXUHWKHH[DFWFHLOLQJKHLJKW
2. Review the chart at right to determine the range
of possible hood installation heights that can be
accomplished with one or more duct covers.
3. Increase or decrease hood installation height to
DFFRPPRGDWHWKHIL[HG´RU´GXFWFRYHUVDQGXVH
DZKROHQXPEHURIGXFWFRYHUVRWKHUZLVHFXWWLQJDQG
modifying one duct cover may be required.
4.'XFWFRYHUVPD\EHVWDFNHGLQYDULRXVFRPELQDWLRQV
to reach ceiling heights.
Actual
Ceiling
Height
*Possible
Hood
Installation
Height 6" Duct Covers 12" Duct Covers
7' 11" 35" 1
8' 0"
8' 0" 30" 36" 1 1
8' 1" 31" 1
8' 2" 32" 1
8' 4" 33" 1
8' 4" 34" 1
8' 5" 35" 1
8' 6"
8' 6" 30" 36" 11
1
8' 7" 31" 1 1
8' 8" 32" 1 1
8' 9" 33" 1 1
8' 10" 34" 1 1
8' 11" 35" 1 1
9' 0"
9' 0" 30" 36" 1 2
1
9' 1" 31" 2
9' 2" 32" 2
9' 3" 33" 2
9' 4" 34" 2
9' 5" 35" 2
9' 6"
9' 6" 30" 36" 1 2
1
9' 7" 31" 1 2
9' 8" 32" 1 2
9' 9" 33" 1 2
9' 10" 34" 1 2
9' 11" 35" 1 2
10' 0"
10' 0" 30" 36" 1 3
2
10' 1" 31" 3
10' 2" 32" 3
10' 3" 33" 3
10' 4" 34" 3
*Based on 36" countertop height.
Note: Additional duct covers may be used to reach
higher ceilings.
Straight or Taper-Sided Hoods
NOTE0LQLPXPFHLOLQJKHLJKWIRU5($5:$//
(;+$867ZLWKGXFWFRYHUVLVZKHQLQVWDOOLQJDW
above countertop using 10" elbow
Installation Height
Ceiling Height
to Floor
Duct Covers
18" Hood
Height

10 31-2000859 Rev. 0
Advance Planning
ADVANCE PLANNING
Ductwork Planning
• These vent hoods are equipped for 10” round
GXFWZRUN)RUEHVWSHUIRUPDQFHXVH´URXQG
ductwork on the 48” wide hoods. 30” and 36” hoods
may be transitioned to 8” round.
• This hood may be vented vertically through upper
FDELQHWVVRIILWRUFHLOLQJ$GXFWWUDQVLWLRQSLHFHLV
VXSSOLHGIRUYHUWLFDOH[KDXVW8VHORFDOO\VXSSOLHG
elbows to vent horizontally through the rear wall.
 'HWHUPLQHWKHH[DFWORFDWLRQRIWKHYHQWKRRG
• 3ODQWKHURXWHIRUYHQWLQJH[KDXVWWRWKHRXWGRRUV
7RPD[LPL]HWKHYHQWLODWLRQSHUIRUPDQFHRIWKHYHQW
V\VWHP
1. Minimize the duct run length and number of
transitions and elbows.
2. Maintain a constant duct size.
3. Seal all joints with duct tape to prevent any leaks.
'RQRWXVHDQ\W\SHRIIOH[LEOHGXFWLQJ
• Use metal ductwork only.
• Install a wall cap or roof cap with damper at the
H[WHULRURSHQLQJ2UGHUWKHZDOORUURRIFDSDQGDQ\
transition needed in advance.
 :KHQDSSOLFDEOHLQVWDOODQ\PDNHXSUHSODFHPHQW
air system in accordance with local building code
requirements. Visit Monogram.com for available
makeup air solutions (search on the words “make-up
air” or “make up air”).
Wall Framing for Adequate Support
 7KHVHYHQWKRRGVDUHKHDY\$GHTXDWHVWUXFWXUDO
support must be provided. Hoods must be secured
to vertical studs in the wall.
• It is strongly recommend that the vent hood with
duct cover be on site before final framing and wall
finishing. This will also help to accurately locate the
ductwork and electrical service.
Decorative Duct Covers:
'HFRUDWLYHGXFWFRYHUV´DQG´KLJKDUH
available to fit all models. The duct cover conceals
the ductwork running from the top of the hood to the
ceiling or soffit. Stack one or more duct covers over
the top of the hood to reach your ceiling height.
POWER SUPPLY
IMPORTANT3OHDVHUHDGFDUHIXOO\
WARNING
)253(5621$/6$)(7<7+,6$33/,$1&(0867
%(3523(5/<*5281'('
AVERTISSEMENT
32859275(3527(&7,213(56211(//(&(7
$33$5(,/'2,7Ç75(&255(&7(0(170,6¬/$
TERRE.
ADVERTENCIA
3$5$686(*85,'$'3(5621$/(67(
(/(&752'20e67,&2'(%(5È(67$5
$'(&8$'$0(17(&21(&7$'2$7,(55$
Remove house fuse or open circuit breaker before
beginning installation.
Electrical supply
7KHVHYHQWKRRGVPXVWEHVXSSOLHGZLWK9+]
DQGFRQQHFWHGWRDQLQGLYLGXDOSURSHUO\JURXQGHG
EUDQFKFLUFXLWDQGSURWHFWHGE\DRUDPSFLUFXLW
breaker or time delay fuse.
:LULQJPXVWEHZLUHZLWKJURXQG
• If the electrical supply does not meet the above
UHTXLUHPHQWVFDOODOLFHQVHGHOHFWULFLDQEHIRUH
proceeding.
• Route house wiring as close to the installation
location as possible on the back wall or ceiling.
• Connect the wiring to the house wiring in accordance
with local codes.
Grounding instructions
The grounding conductor must be connected to
DJURXQGPHWDOSHUPDQHQWZLULQJV\VWHPRUDQ
equipment-grounding terminal or lead on the hood.
WARNING The improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
appliance is properly grounded.
AVERTISSEMENT 8QHFRQQH[LRQLQFRUUHFWHGX
conducteur de terre de l’appareil peut poser un risque
de choc électrique. Consultez un électricien agréé ou un
représentant du service de réparation si vous avez des
GRXWHVTXDQWjO¶H[DFWLWXGHGHODPLVHjODWHUUHGHO¶DSSDUHLO
ADVERTENCIA 8QDFRQH[LyQLQDSURSLDGDGHO
FRQGXFWRUGHFRQH[LyQDWLHUUDGHOHTXLSRSRGUiSURYRFDU
riesgos de descargas eléctricas. Consulte a un electricista
calificado o a personal del servicio técnico si tiene dudas de
que el electrodoméstico se encuentre conectado a tierra de
forma apropiada.

31-2000859 Rev. 0 11
STEP 1 DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS
• Use a level to draw the cooktop centerline location.
Draw the line to ceiling height.
• Measure desired distance from the bottom of the
hood to the cooking surface, 30” min. to 36” max.
NOTE: If you are installing the hood with duct
covers, be sure to read “Using Duct Cover
Accessories” page 7. Exact installation height may
be determined by use of one or more duct covers.
• Use a level to draw a straight horizontal pencil line
indicating the bottom of the hood.
)URPWKHOLQHLQGLFDWLQJWKHERWWRPRIWKHKRRG
measure 15-3/8” up and draw another line for the
location of the wood support. See illustration.
FOR VERTICAL (Straight Up) DUCTING:
• Use a level to draw a centerline from the bottom of the
hood to ceiling or soffit.
,IYHQWLQJRXWWKHFHLOLQJH[WHQGWKHFHQWHUOLQHIRUZDUG
on the ceiling or soffit.
• Locate the centerline of a 10-1/2” hole on the ceiling or
soffit by measuring 6” from the wall.
HOUSE WIRING LOCATION:
7KHMXQFWLRQER[LVIDVWHQHGWRWKHEDFNRIWKHKRRGRQ
the right side.
• The recessed back side of the hood provides a large
DUHDIRUWKHKRXVHZLULQJWRH[LWWKHZDOODQGEHURXWHG
WRWKHUHDUNQRFNRXWDQGMXQFWLRQER[
5HPRYHMXQFWLRQER[FRYHUDQGNQRFNRXW,QVWDOOVWUDLQ
relief.
Alternate Knockout Locations
,IWKHLQVWDOODWLRQUHTXLUHVWKHMXQFWLRQER[FDQEH
relocated from the back to the top of the hood. Remove
VFUHZVDOLJQER[WRWRSNQRFNRXWDQGVHFXUHZLWK
original screws.
5HPRYHMXQFWLRQER[FRYHUDQGNQRFNRXW,QVWDOOVWUDLQ
relief.
Installation Instructions
6-1/2"
18-1/16" for 48" Models
12-1/16" for 36" Models
9-1/16" for 30" Models
18-13/16" for 48" Models
12-13/16" for 36" Models
9-13/16" for 30" Models
Electrical
Area
8-3/8"
FOR DUCTING THROUGH REAR WALL:
• Measure 9-7/8” above the marked line for the top of
WKHKRRG$WWKHFHQWHUOLQHPDUNORFDWLRQIRUD´
diameter hole.
NOTE: 0LQLPXQFHLOLQJKHLJKWIRU5($5:$//
(;+$867ZLWKGXFWFRYHUVLV¶´ZKHQLQVWDOOLQJDW
30” above countertop using 10” elbow

12 31-2000859 Rev. 0
Installation Instructions
STEP 2A INSTALL HOOD ONTO WALL
IMPORTANT: Framing must be capable of supporting up to 150 lbs.
SKIP THIS STEP IF INSTALLING BENEATH A
SOFFIT OR CABINET, GO TO STEP 2B.
• Locate at least 2 vertical studs at the wood support.
)RU´PRGHOVLIYHUWLFDOVWXGVFDQQRWEHORFDWHG
then install 2 screws through the wood support into the
VWXGWKDWLVORFDWHGYHUWLFDOO\DOLJQHGZLWKWKHVFUHZV
located ½” from the edge of the wood support.
&HQWHUWKHVXSSOLHGZRRGVXSSRUWOHIWWRULJKWDQG
below the 15-3/8” marked line.
6HFXUHWKHZRRGVXSSRUWWRRUPRUHYHUWLFDOVWXGV
XVLQJDWOHDVWRIWKHVXSSOLHGORQJVFUHZV)RUWKH
´PRGHO\RXPD\QHHGWRDGGIUDPLQJWRH[LVWLQJ
framing to secure the wood support to 2 studs.
IMPORTANT: Screws must penetrate at least 1” into
vertical studs. Countersink screws into support.
$GMXVWGHSWKRIRULJLQDOPRXQWLQJVFUHZVLQWKHZRRG
support until they protrude 1/4” forward. This 1/4” gap
will provide clearance to hang the hood.
• Use duct tape to seal the transition duct connection.
Check to be sure the damper moves freely.
Hang Hood On Wood Support
• Lift the hood and hold close to the installation location.
Route house wiring through the knockout and into the
MXQFWLRQER[
3ODFHWKHKRRGRYHUWKHZRRGVXSSRUW%HVXUHWKH
mounting screws engage the keyhole slots in the back
of the hood. Tighten the screws.
• Install additional 4 screws to secure the hood to the
wood support.
• Drill 1/8” pilot holes into the two lower holes. If the pilot
KROHHQWHUVDVWXGXVHDZDVKHUDQGWKHORQJZRRG
VFUHZ,IWKHSLORWKROHGRHVQRWHQWHUDVWXGHQODUJH
WKHKROHWR´WRDFFHSWWKHZDOODQFKRUDQGXVHD
washer and the screw from the wall anchor.
Centerline of
Installation
Space
15-3/8"
30"
to
36"
Wood
Support
NOTE: The mounting
screws must remain
in their original
shipping location.
These screws are
positioned to engage
the keyhole slots in
the back of the hood.
1/4"
Gap
Original Mounting
Screws as Shipped
Centerline of
Installation
Space
30"
to
36"

31-2000859 Rev. 0 13
STEP 2B Alternate Mounting Method
INSTALL HOOD TO SOFFIT OR BENEATH CABINETS
IMPORTANT: Soffit framing must be capable of supporting up to 150 lbs.
SKIP THIS STEP IF USING WALL MOUNTING
METHOD
:KHQQHFHVVDU\WKHKRRGPD\EHLQVWDOOHGVRWKDWLWLV
supported by the soffit.
7KHVRIILWVKRXOGEHFRQVWUXFWHGZLWK[¶V
• Determine the installation location on the wall.
• Continue the centerline forward on the bottom of the
cabinet or soffit.
• The opening above the hood should allow for the
10” round duct and clearance to slide the hood back
against the wall.
7KH[VWXGVPXVWEHORFDWHGDVVKRZQLQWKHFKDUW
'LP$WRDFFHSWPRXQWLQJVFUHZV
• Drill 1/8” pilot holes into the studs at the locations
shown in the top view illustration.
• Use duct tape to seal the transition duct connection.
Check to be sure the damper moves freely.
Mount Hood onto Soffit or Cabinet
NOTE: If mounting to the underside of a cabinet with a
UHFHVVHGERWWRPLQVWDOOVKLPVWRILOOWKHJDS
• Drive mounting screws into the studs until they
protrude 1/4”. The 1/4” gap will provide clearance to
engage the keyhole slots in the top of the hood.
• Lift hood to installation position. Locate house wiring
and route through the knockout (from the back or top
of the hood).
• Lift hood onto mounting screws. Slide back against the
rear wall.
• Tighten mounting screws.
IMPORTANT: For additional support and to
minimize vibration during operation, the hood
must be secured to the back wall. Use wall
anchors to fasten bottom back of hood to the wall.
Installation Instructions
A
Requires 10-1/2" Min.
Opening For Ductwork
and Hood Installation
A
“A” Centerline
to Stud and
Keyhole Slots
“B” Hood Width At
the Top
ZV48T 19-9/16" 40"
ZV48S 23-9/16" 47-15/16"
ZV36T 13-9/16" 28"
ZV36S 17-9/16" 35-15/16"
ZV30T 10-9/16" 22"
ZV30S 14-9/16" 29-15/16"
2"
7-1/2"
A
B
2-9/16"
10"
3/4"
Back of Hood
Top View
Front of Hood
1/4" Gap
Push Back
to Wall
Add Shims
If Bottom
Is Recessed
Back
Wall
Cabinet
or
Soffit
Engage Top
Keyhole Slots

14 31-2000859 Rev. 0
Installation Instructions
STEP 3 CONNECT DUCTWORK
,QVWDOOGXFWZRUNPDNLQJFRQQHFWLRQVLQGLUHFWLRQRI
airflow as illustrated.
• Secure joints in ductwork with sheetmetal screws.
:UDSDOOGXFWMRLQWVZLWKGXFWWDSHIRUDQDLUWLJKW
seal.
• Use duct tape to seal the flange connection. Reach
inside the hood and push the damper up to be sure
it moves freely.
STEP 5 INSTALL DUCT COVERS
NOTE:)RUHDVLHUKDQGOLQJUHPRYHFDUGERDUGLQVHUW
after film is peeled off.
Remove protective film from duct covers. If more than
RQHGXFWFRYHULVXVHGVHFXUHHDFKSLHFHWRJHWKHU
with screws provided.
3ODFHWKHGXFWFRYHUVRQWRSRIWKHKRRG
)URPLQVLGHWKHKRRGVHFXUHWKHGXFWFRYHUWRWKH
WRSZLWKWKHVPDOO3KLOOLSVKHDGVFUHZVVXSSOLHGZLWK
the covers.
STEP 4 CONNECT ELECTRICAL
Verify that power is turned off at the source.
WARNING If house wiring is not 2-wire with
DJURXQGZLUHDJURXQGPXVWEHSURYLGHGE\WKH
LQVWDOOHU:KHQKRXVHZLULQJLVDOXPLQXPEHVXUH
WRXVH8/DSSURYHGDQWLR[LGDQWFRPSRXQGDQG
aluminum-to-copper connectors.
AVERTISSEMENT Si le câblage électrique de la
PDLVRQQ¶HVWSDVFRQVWLWXpGHILOVDYHFXQILOGHWHUUHOHILO
de terre doit être ajouté par l’installateur. Lorsque le câblage
HVWHQDOXPLQLXPDVVXUH]YRXVG¶XWLOLVHUXQFRPSRVp
DQWLR[\GDQWHWGHVFRQQHFWHXUVDOXPLQLXPVXUFXLYUH
approuvés U.L.
ADVERTENCIA Si el cableado del hogar no tiene
FDEOHVFRQXQRDWLHUUDHOLQVWDODGRUGHEHUiSURYHHUXQD
FRQH[LyQDWLHUUD&XDQGRHOFDEOHDGRGHOKRJDUVHDGH
DOXPLQLRDVHJ~UHVHGHXVDUXQFRPSXHVWRDQWLR[LGDQWH\
conectores de aluminio a cobre aprobados por U.L.
• Use wire nuts to
connect incoming
JURXQGWRJUHHQZKLWH
to white and black to
black.
3XVKZLUHVLQWRMXQFWLRQ
ER[DQGUHSODFHFRYHU
Be sure wires are not
pinched.
Screw
Duct Tape
Over Seam
and Screw
Air Flow
Duct Tape
Over Transition
White
Ground Black
Remove
Junction Box
Cover
Insert Power
Conduit Thru
Strain Relief
and Tighten
Use UL Listed
Wire Nuts
A
B
C

31-2000859 Rev. 0 15
Installation Instructions
STEP 6 INSTALL FILTERS
3ODFHILOWHUGULSWUD\VLQWRWKHUHDURIWKHKRRG
• Insert the grease filter into the opening and drop into
the trays.
7RUHPRYHWKHILOWHUVJUDVSWKHKDQGOHSXVKWKH
filter up and lift out.
STEP 7 INSTALL IMPLEMENT
RODS
• Use a flat blade screwdriver to install stand-offs into
the bottom of the hood.
$OLJQLPSOHPHQWURGWRVWDQGRIIVZLWKWKHVFUHZ
hole towards the inside of the hood. Secure the rod
WRWKHVWDQGRIIVZLWKWKHVXSSOLHG$OOHQZUHQFK
)ROORZWKHVDPHSURFHGXUHRQWKHRSSRVLWHVLGH
• Install knobs - line up the flat on the shaft with the
flat in the knob hole.
$WWDFK0RQRJUDPQDPHSODWHEDGJH8VHWKH
template on page 14 for alignment of the nameplate.
Cut out the template and tape it onto the hood
front surface and verify the template is aligned with
the left side of the hood and within the upper and
ORZHUHGJHRIWKHIURQWVXUIDFH3UDFWLFHSODFLQJ
the nameplate first before removing the adhesive
release paper.
Screw
Stand-offs
Into
Hood
Use Allen
Wrench to
Secure Rod
to Stand-offs
Template for
Monogram
nameplate
Monogram
nameplate
FINALIZE INSTALLATION
• Install the supplied infrared bulb(s).
• See the Owner’s Manual for instructions to test
operation.

16 31-2000859 Rev. 0
Notes

31-2000859 Rev. 0 17
Notes

NOTE::KLOHSHUIRUPLQJLQVWDOODWLRQVGHVFULEHGLQWKLVERRN
safety glasses or goggles should be worn.
)RU0RQRJUDP®ORFDOVHUYLFHLQ\RXUDUHDYLVLW
monogram.com or call 1.800.444.1845
NOTE:3URGXFWLPSURYHPHQWLVDFRQWLQXLQJHQGHDYRUDW
0RQRJUDP$SSOLDQFHV7KHUHIRUHPDWHULDOVDSSHDUDQFH
and specifications are subject to change without notice.
31-2000859 Rev. 0
10-20 GEA
Printed in Italy