Monogram ZVC48DTB1 User manual

INSTALLATION
INSTRUCTIONS
48”Custom Brass Hood
ZVC48DTB1
48” Custom Stainless Steel Hood
ZVC48STSS
MONOGRAM.COM

231-2001216 Rev. 0
Safety Information
READ AND SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
ŶIMPORTANT— Save these instructions
for local inspector’s use.
ŶIMPORTANT— Observe all governing
codes and ordinances.
ŶNote to Installer — Be sure to leave these
instructions with the Consumer.
ŶNote to Consumer — Keep these instructions with
your Owner’s Manual for future reference.
ŶSkill Level — Installation of this appliance requires
basic mechanical and electrical skills.
Ŷ3URSHULQVWDOODWLRQLVWKHUHVSRQVLELOLW\RIWKH
LQVWDOOHU3URGXFWIDLOXUHGXHWRLPSURSHULQVWDOODWLRQ
is not covered under the warranty. See Owner’s
Manual for warranty information.
WARNING Improper grounding can result in a
risk of electric shock. Consult a qualified electrician
if the grounding instructions are not completely
understood, or if doubt exists as to whether the
appliance is properly grounded.
For Monogram local service in your area,
800.444.1845.
For Monogram Service in Canada, call 800.561.3344.
)RU0RQRJUDP3DUWVDQG$FFHVVRULHVFDOO
800.626.2002.
If you received a damaged vent hood, you should
contact your dealer.
CAUTION Due to the weight and size of these
vent hoods and to reduce the risk of personal injury
or damage to the product, TWO PEOPLE ARE
REQUIRED FOR PROPER INSTALLATION.
WARNING TO REDUCE THE RISK OF FIRE,
(/(&75,&$/6+2&.25,1-85<723(56216
2%6(59(7+()2//2:,1*
Ŷ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\
qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
Ŷ:KHQFXWWLQJRUGULOOLQJLQWRZDOOVRUFHLOLQJVGRQRW
damage electrical wiring and other hidden utilities.
Ŷ'XFWHGV\VWHPVPXVWDOZD\VEHYHQWHGWRWKHRXWGRRUV
CAUTION To reduce risk of fire and to properly
exhaust air, be sure to duct air outside — do not vent
exhaust air into spaces within walls or ceilings or into
attics, crawl spaces or garages.
WARNING TO REDUCE THE RISK OF FIRE,
86(21/<0(7$/'8&7:25.

31-2001216 Rev. 0 3
Installation Instructions
CONTENTS
Safety Information.........................................................2
3URGXFW'LPHQVLRQV ......................................................3
$GGLWLRQDO3DUWV3URYLGHG..............................................3
Tools and Materials Required.......................................3
Installation Clearances..................................................4
$GYDQFH3ODQQLQJ .........................................................4
Unboxing .......................................................................4
Step 1, Determine Ductwork and Wiring Locations ......5
Step 2, Install Hood onto Wall.......................................6
Step 3, Install Hood Insert into Hood............................7
PRODUCT DIMENSIONS
ADDITIONAL PARTS PROVIDED
These parts are packed with the hood. TOOLS AND MATERIALS REQUIRED 1RWVXSSOLHG
30”
17-5/8”
24”
SIDE VIEW FRONT VIEW
38”
48”
Phillips screwdriver
Flashlight
Safety glasses
Electric or battery operated drill.
1/8” drill bit. 3/16” drill bit.
Phillips driver.
Pencil
Level Step ladder
Tape measure
Safety Gloves
Wood Support with
short Phillips head screws
2 long Square Drive flat head
screws to secure the wood
support to the wall
Square drive bit
2 short pan head Phillips screws to
secure the hood to the wood support.
There are 2 additional screws already
installed in the wood support.
4 medium pan head Phillips screws to
secure the hood to the wall.
*UHHQ
*URXQG6FUHZV 3DLUVRI1LWULOH
*ORYHVWRSUHYHQW
fingerprinting)
*URXQG:LUH

431-2001216 Rev. 0
Installation Instructions
INSTALLATION CLEARANCES
This hood is designed to be installed onto a wall.
Install this hood 30" minimum to 36" maximum above the
cooking surface.
In this installation, the ductwork running from the top
of the hood will be concealed in the soffit or upper
cabinetry.
In this installation, the ductwork running from the back
of the hood goes directly into the wall.
ADVANCED PLANNING
Ductwork Planning
Ŷ&DUHIXOO\UHYLHZWKHGXFWZRUNLQVWDOODWLRQPHWKRGDV
described later in this instruction as well as the hood
insert installation instructions.
Wall Framing for Adequate Support
Ŷ7KLVKRRGLVKHDY\$GHTXDWHVWUXFWXUDOVXSSRUWPXVW
be provided. Hood must be secured to vertical studs in
the wall.
Ŷ,WLVVWURQJO\UHFRPPHQGHGWKDWWKHKRRGDQGKRRG
insert be on site before final framing and wall finishing.
This will also help to accurately locate the ductwork
and electrical service.
UNBOXING
NOTE: Clearances may vary due to type of
cooking product and local codes. Check with local
inspectors to be sure standard is applicable.
SOFFIT OR UPPER CABINETS
Top Vent Installation
30" MIN.
36" MAX.
Back Vent Installation
30" MIN.
36" MAX.
Cut Straps Remove Top Remove Sleeve Remove Hood

31-2001216 Rev. 0 5
Installation Instructions
STEP 1 DETERMINE HOOD AND DUCTWORK LOCATIONS
MARK LOCATION OF WOOD SUPPORT
Ŷ8VHDOHYHOWRGUDZDFRRNWRSFHQWHUOLQHORFDWLRQ
Draw the line to ceiling height.
Ŷ0HDVXUHGHVLUHGGLVWDQFHIURPWKHERWWRPRIWKHKRRG
to the cooking surface, 30” min. to 36” max.
Ŷ8VHDOHYHOWRGUDZDVWUDLJKWKRUL]RQWDOSHQFLOOLQH
indicating the bottom of the hood.
Ŷ)URPWKHOLQHLQGLFDWLQJWKHERWWRPRIWKHKRRG
measure 16” up and draw another line for the location
of the top of the wood support.
Ŷ)URPWKHOLQHLQGLFDWLQJWKHERWWRPRIWKHKRRG
measure 30” up and draw another line for the location
of the top of the hood. See illustration.
16”
Bottom of Hood
Wood
Support
Top of Hood
30”
FOR VERTICAL (Straight Up) DUCTING:
Ŷ8VHDOHYHOWRGUDZDFHQWHUOLQHIURPWKHERWWRPRIWKH
hood to ceiling or soffit.
Ŷ([WHQGWKHFHQWHUOLQHIRUZDUGRQWKHFHLOLQJRUVRIILW
Ŷ0DUNWKHFHQWHURID´KROHRQWKHFHLOLQJRUVRIILW
E\PHDVXULQJ´IURPWKHZDOO
FOR DUCTING THROUGH REAR WALL:
Ŷ0HDVXUH´DERYHWKHPDUNHGOLQHIRUWKHWRSRI
WKHZRRGVXSSRUW$WWKHFHQWHUOLQHPDUNORFDWLRQIRUD
´GLDPHWHUKROH
HOUSE WIRING LOCATION:
Ŷ+RXVHZLULQJWRFRPHWKURXJKZDOODVVKRZQ3URYLGH
at least 7 feet of house wiring.
10-1/2” hole
8-3/4”
Bottom of Hood
Wood
Support
Top of Hood
6-1/2”
10-1/2” hole
Wood
Support
Top of Hood
House wiring comes
through here
2”
3”
9” 32”

631-2001216 Rev. 0
Installation Preparation
STEP 2 INSTALL HOOD TO WALL
Mount Wood Support to Wall
Ŷ/RFDWHDWOHDVWYHUWLFDOVWXGVDWWKHZRRGVXSSRUW
Ŷ&HQWHUWKHVXSSOLHGZRRGVXSSRUWOHIWWRULJKWDQG
below the 16” marked line. Use the center hole in the
wood support as guidance.
Ŷ0DUNDQGGULOOWZR´KROHVWKURXJKZRRGVXSSRUWWR
match stud locations.
Ŷ6HFXUHWKHZRRGVXSSRUWWRRUPRUHYHUWLFDOVWXGV
using 2 long, square drive screws.
IMPORTANT: Screws must penetrate at least 1” into
vertical studs. Countersink screws in support.
NOTE: The two supplied mounting screws must remain
in their original shipping location. These screws are
positioned to engage the keyhole slots in the back of the
hood.
Ŷ$GMXVWGHSWKRIVXSSOLHGPRXQWLQJVFUHZVLQWKHZRRG
VXSSRUWXQWLOWKH\SURWUXGH´IRUZDUG7KLV´JDS
will provide clearance to hang the hood.
IMPORTANT: Framing must be capable of
supporting up to 150 lbs.
Ŷ3ODFHWKHKRRGRYHUWKHZRRGVXSSRUW%HVXUHWKH
mounting screws engage the keyhole slots in the
back of the hood. Tighten the screws. Confirm hood
position is correct.
Ŷ,QVWDOODGGLWLRQDOVKRUWVFUHZVWRVHFXUHWKHKRRGWR
the wood support.
Ŷ,QVWDOOPHGLXP3KLOOLSVVFUHZVDWWRSLQVLGHRIWKH
hood into studs. Chose the appropriate holes that line
up with studs.
Ŷ,QVWDOOPHGLXP3KLOOLSVVFUHZVDWERWWRPLQVLGHRI
hood into studs. Choose the appropriate holes that
line up with studs.
30”
to
36”
16” Wood Support
Centerline of
Installation
Space
Mounting Screws
as Shipped
1/4”
Gap
Centerline of
Installation
Space
30”
to
36”
Keyhole Slots
choose screw holes that line up with studs
choose screw holes that line up with studs

31-2001216 Rev. 0 7
Installation Preparation
STEP 3 PREPARE CUSTOM HOOD INSERT (UVC9420) FOR INSTALLATION
5HIHUQRZWRWKHLQVWDOODWLRQLQVWUXFWLRQVIRUWKH&XVWRP+RRG,QVHUW89&ZLWKWKHIROORZLQJH[FHSWLRQV
Ŷ'LVUHJDUGDQ\UHIHUHQFHWREXLOGLQJDFXVWRPZRRG
canopy.
Ŷ)RUGXFWSODQQLQJDQGHOHFWULFDOSODQQLQJ\RXZLOO
need to refer to these instructions as some of the
dimensions are different.
WARNING During Step 2 (Connect Electrical
Cables),install the provided ground wire included in this
product’s hardware bag.
Ŷ&RQQHFWRQHHQGRIWKHSURYLGHG*URXQG:LUHWRWKH
,QVHUW*URXQG6FUHZLQWKH,QVHUW-XQFWLRQ%R[
Ŷ%HVXUHWKDWWKH+RXVH*URXQG:LUHDQGWKH+RRG
*URXQG:LUHDUHERWKFRQQHFWHGWRWKH,QVHUW*URXQG
Screw.
Ŷ&RQQHFWWKHRWKHUHQGRIJURXQGZLUHWRRQHRIWKH´
Hood ground holes using the provided green screw.
STEP 4 INSTALL HOOD INSERT INTO HOOD
Ŷ%HVXUHWRIROORZWKHUHPDLQGHURIWKH&XVWRP+RRG
Insert installation instructions to properly fasten the
Insert to the Hood.
Ŷ%HVXUHWRSXVKWKH,QVHUWILUPO\XSSULRUWRGULYLQJWKH
mounting screws. This will prevent any visible gaps
between the Insert and the Hood.
Use screws provided with the Insert to attach
the Insert to the Hood as directed
in the Insert Installation Instructions.
*URXQG+ROH/RFDWLRQLQ+RRG
*URXQG6FUHZ
LQ-XQFWLRQ
Box
House
*URXQG:LUH
*URXQG:LUH
with
ring terminal
3URYLGHG
with Hood

31-2001216 Rev. 0
05-23 GEA
Printed in the United States
NOTE: While performing installations described in this book, safety glasses or
goggles should be worn.
NOTE: Product improvement is a continuing endeavor at Monogram. Therefore,
materials, appearance and specifications are subject to change without notice.