Monogram ZVW1360 User manual

INSTALLATION
INSTRUCTIONS
36” and 48” Wall Hood
ZVW1360, ZVW1480
With QuietBoost™ Blower
MONOGRAM.COM
Para consultar una version en español
de este manual de instrucciones, visite nuestro
sitio de internet monogram.com.

231-2000734 Rev. 4
Safety Information
READ AND SAVE THESE INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
ŶIMPORTANT— Save these
instructions for local inspector’s use.
ŶIMPORTANT— Observe all governing
codes and ordinances.
ŶNote to Installer – Be sure to leave these
instructions with the Consumer.
ŶNote to Consumer – Keep these instructions for
future reference.
ŶSkill level – Installation of this vent hood
requires basic mechanical and electrical skills.
ŶCompletion time – Approximately 1 to 3 hours
ŶProper installation is the responsibility of the
installer.
ŶProduct failure due to improper installation is
not covered under the Warranty.
FOR YOUR SAFETY
WARNING Before beginning the installation,
switch power off at service panel and lock the
service disconnecting means to prevent power
from being switched on accidentally. When the
service disconnecting means cannot be locked,
securely fasten a prominent warning device, such
as a tag, to the service panel.
CAUTION Due to the weight and size
of these vent hoods and to reduce the risk
of personal injury or damage to the product,
TWO PEOPLE ARE REQUIRED FOR PROPER
INSTALLATION.
WARNING Disconnect all electrical power
at the main circuit breaker or fuse box before
installing.
WARNING TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
B. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code
authorities.
C. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
D. Ducted fans must always be vented to the
outdoors.
E. Turn off breaker to adjacent rooms while working.
WARNING TO REDUCE THE RISK OF FIRE,
USE ONLY METAL DUCT WORK.

31-2000734 Rev. 4 3
Installation Preparation
PRODUCT DIMENSIONS
36” Models
Requires a 36” opening.
48” Models
Requires a 48” opening.
18”
15” 23-5/8”
22” 36”
18”
22” 48”
15” 35-5/8”

431-2000734 Rev. 4
TOOLS AND MATERIALS REQUIRED
(NOT SUPPLIED)
Wire cutter/stripper
Level
Aluminized
duct tape
Safety glasses
Phillips screwdriver with
at least 6” shank
Strain relief for
junction box, 1”
diameter knockout
Electric drill with #2 Phillips
with 1/8” and 5/16” drill bits
UL listed wire nuts
Pencil and tape measure
Gloves
Installation Preparation
12" round duct
8”x12” to 12” round
duct transition
Needed for back venting only
10” round duct
PLAN THE INSTALLATION
CAUTION To reduce risk of fire and to properly
exhaust air, be sure to duct the air outside. Do not
vent exhaust air into spaces within walls or ceilings or
into attics, crawl spaces, or garages.
PARTS SUPPLIED FOR INSTALLATION
Ŷ1 Hardware Package
Ŷ1 Literature Package
Ŷ1 Installation Template
PARTS NEEDED FOR INSTALLATION
Ŷ1 Strain Relief
Ŷ1 Wall or Roof Cap
ŶAll Metal Ductwork
WARNING
PERSONAL INJURY HAZARD
Because of the weight and size of the rangehood
canopy. It is recommended that 2 people are used
to install the range hood. Failure to properly lift
rangehood could result in damage to the product or
personal injury.
NOTE: Before making any cuts or holes for
installation, determine which venting method will be
used and carefully calculate all measurements.
REMOVE THE PACKAGING
CAUTION Wear gloves to protect against sharp
edges.
ŶRemove the hood body.
ŶRemove the hardware bag, literature package and
other boxed parts.
ŶRemove and properly discard the protective plastic
wrapping and other packaging materials.
ŶConsider recycling options for your appliance
packaging material.

31-2000734 Rev. 4 5
Installation Preparation
PARTS PROVIDED
Locate the parts packed with the hood. HARDWARE PACKAGE Locate and check contents.
Top Damper
Grease Drip Trays
Motor
(2 with 48” model)
Hood Body
Metal Installation Bracket
3 Baffle Filters
(4 with 48” models)
(QTY:2) 3/16” dry wall
anchors with screws. Used
for hood bottom mounting
screw holes. Use 5/16” drill
for pilot hole.
(QTY: 4 or 8) M4 screws.
Used to mount motor
(QTY: 4) 8 x 1-3/4 AB
screw. Used to mount the
installation bar. Use 1/8”
drill for pilot hole
(QTY: 4) 2.9mm x 6mm
PZ screws. Used to
attach the damper
AB
C
D

631-2000734 Rev. 4
INSTALLATION DIMENSIONS
The hood duct covers can be adjusted for different
ceiling heights depending on the distance between the
bottom of the hood and the cooktop (distance X). See
Installation Height Table.
Installation Preparation
DUCT COVER REQUIREMENTS
Duct cover kits must be purchased separately.
We recommend that the vent hood and duct cover
(if used) be on site before final framing and wall
finishing. This will help to accurately locate studs,
ductwork and electrical service.
• Duct cover accessory comes with a lower and upper
duct cover and installation hardware.
• The installation hardware includes mounting
brackets to secure duct covers to the wall.
• The lower duct cover alone can be used and must
be secured with the duct cover bracket.
• See table below for duct cover kit part numbers
based on model.
• See the next page for duct cover installation height
information.
X = Distance from hood to cooktop. (Varies
depending on the installation) Required 24”
minimum over electric range or 30” minimum over
gas range. The recommended maximum is 36”.
Required Min & Recommended Max Ceiling
Height Examples for 10’ Duct Cover Kit
(Vented)
Electric Gas
X = 24”
Y = Min 8’ 3”
Max 9’ 6”
X = 30”
Y = Min 8’ 11”
Max 10’ 2”
X = 36”
Y = Min 9’ 5”
Max 10’ 8”
Typical Range
Upper Duct
Cover
1” Min.
16-1/2”
Max.
20”
18”
X
36”
or
38”
Lower Duct Cover
Model Duct Cover # Max Ceiling
Installation
36” Model ZX8D13SPSS 8’ 4” ZX10D13SPSS 10’ 8”
ZX12D13SPSS 12’ 8”
48” Model ZX8D14SPSS 8’ 4” ZX10D14SPSS 10’ 8”
ZX12D14SPSS 12’ 8” NOTE: 36” for typical
electric range and 38” for
gas range.
Y

31-2000734 Rev. 4 7
INSTALLATION HEIGHT TABLE
Installation Preparation
ZX8D13SPSS
OR ZX8D14SPSS ZX10D13SPSS OR ZX10D14SPSS ZX12D13SPSS OR ZX12D14SPSS
Ceiling Duct Cover up to 8 ft. High Ceiling Duct Cover up
to 10 ft. High Ceiling Duct Cover up to 12 ft.
Ceiling Height
(ft./in.) Installation Over Gas
Range
Installation
Over Electric
Range
Ceiling Height
(ft./in.) Installation Over Gas
Range
Installation
Over Electric
Range
Ceiling Height
(ft./in.) Installation Over Gas
Range
Installation
Over Electric
Range
7’ 0” 24 8’ 3” 24 9’ 4” 24
7’ 1” 24-25 8’ 4” 24-25 9’ 5” 24-25
7’ 2” 24-26 8’ 5” 24-26 9’ 6” 24-26
7’ 3” 25-27 8’ 6” 24-27 9’ 7” 24-27
7’ 4” 26-28 8’ 7” 24-28 9’ 8” 24-28
7’ 5” 27-29 8’ 8” 24-29 9’ 9” 24-29
7’ 6” 28-30 8’ 9” 24-30 9’ 10” 24-30
7’ 7” 29-31 8’ 10” 24-31 9’ 11” 24-31
7’ 8” 30 30-32 8’ 11” 30 24-32 10’ 0” 30 24-32
7’ 9” 30-31 31-33 9’ 0” 30-31 24-33 10’ 1” 30-31 24-33
7’ 10” 30-32 32-34 9’ 1” 30-32 24-34 10’ 2” 30-32 24-34
7’ 11” 31-33 33-35 9’ 2” 30-33 24-35 10’ 3” 30-33 24-35
8’ 0” 32-34 34-36 9’ 3” 30-34
24-36
10’ 4” 30-34
24-36
8’ 1” 33-35 35-36 9’ 4” 30-35 10’ 5” 30-35
8’ 2” 34-36 36 9’ 5”
30-36
10’ 6”
30-36
8’ 3” 35-36 9’ 6” 10’ 7”
8’ 4” 36 9’ 7” 25-36 10’ 8”
9’ 8” 26-36 10’ 9”
9’ 9” 27-36 10’ 10”
9’ 10” 28-36 10’ 11”
9’ 11” 29-36 11’ 0”
10’ 0” 30-36 11’ 1”
10’ 1” 31-36 11’ 2”
10’ 2” 32-36 11’ 3”
10’ 3” 31-36 33-36 11’ 4”
10’ 4” 32-36 34-36 11’ 5”
10’ 5” 33-36 35-36 11’ 6”
10’ 6” 34-36 36 11’ 7” 25-36
10’ 7” 35-36 11’ 8” 26-36
10’ 8” 36 11’ 9” 27-36
11’ 10” 28-36
11’ 11” 29-36
12’ 0” 30-36
12’ 1” 31-36
12’ 2” 32-36
12’ 3” 31-36 33-36
12’ 4” 32-36 34-36
12’ 5” 33-36 35-36
12’ 6” 34-36 36
12’ 7” 35-36
12’ 8” 36

831-2000734 Rev. 4
Installation Preparation
ADVANCE PLANNING
Duct Install Planning
ŶThis hood is designed to be vented vertically
through the ceiling with a 10” round duct or,
horizontally through a wall with an 8”x12” duct
transition and 12” round duct.
ŶUse metal ductwork only.
ŶPlan the route for venting exhaust to the outdoors.
To maximize the ventilation performance of the vent
system:
1.Minimize the duct run length and number of
transitions and elbows.
2.Maintain a constant duct size.
3.Seal all joints with duct tape to prevent any leaks.
NOTE: Flexible vent is not recommended. Flexible
vent creates back pressure and air turbulence that
greatly reduces performance.
ŶMaximum equivalent duct length for 100 CFM:
150 foot for vent hoods.
ŶInstall a wall cap or roof cap with damper at the
exterior opening. Purchase the wall or roof cap and
any transition and length of duct needed in advance.
ŶWhen applicable, install any makeup (replacement)
air system in accordance with local building code
requirements. 10” round duct universal make up air
kit can be purchased locally.
Vent system can terminate either through the roof
or the wall.
POWER SUPPLY
IMPORTANT – (Please read carefully)
WARNING
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with
this appliance. Follow National Electrical Codes or
prevailing local codes and ordinances.
Electrical supply
These vent hoods must be supplied with 120V, 60Hz,
and connected to a properly grounded branch circuit,
and protected by a 15 or 20 amp circuit breaker or
time delay fuse.
ŶWiring must be 2 wire with ground.
ŶIf the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
ŶRoute house wiring as close to the installation
location as possible in the ceiling or wall.
ŶConnect the wiring to the house wiring in
accordance with local codes.
Grounding instructions
The grounding conductor must be connected to
a ground metal, permanent wiring system, or an
equipment-grounding terminal or lead on the hood.
WARNING The improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or
service representative if you are in doubt whether the
appliance is properly grounded.
Roof Cap
Round Duct
Wall Cap
Add Insulation
and/or Caulk
Add tape to joint
Hood
Top Venting Setup
Add Tape to
Joint
Add Insulation
and/or Caulk
Back Venting
Setup

31-2000734 Rev. 4 9
NEW CONSTRUCTION, PRE-PLANNING, OR REMODELING
NOTE: For existing instruction, skip to the next section.
FOR TOP VENTING
Ŷ)RUGXFWHGLQVWDOODWLRQWKURXJKWKHWRSWKH´
diameter hole for the duct in the ceiling must be
centered 6-1/4” away from the finished rear wall in the
installation space.
FOR BACK VENTING
Ŷ)RUGXFWHGLQVWDOODWLRQWKURXJKWKHEDFNWKH´+
x13-1/4”W cut out for the duct in the wall must be
centered in the installation space, left to right and
located 5-7/8” above intended install height from
bottom of the hood.
Installation Preparation
6-1/4”
5-7/8”
10-1/2”H x13-1/4” W
Bottom of Hood
Ŷ7KHKRRGMXQFWLRQER[NQRFNRXWLVORFDWHG´WRWKH
left from center of the hood. Ensure enough wire length is
available to make electrical connection.

10 31-2000734 Rev. 4
Installation Preparation
DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS
• This hood can be installed onto the wall or underneath
the soffit.
• For installing the hood to soffit, refer to page 12 for
alternate mounting method.
• A wall mounting template is included with the product
for ease of installation. Follow the instructions below if
the template is not being used.
• Measure desired distance from the bottom of the hood
to the cooking surface, 24” minimum over electric range
or 30” minimum over gas range and 36” recommended
maximum.
• Use a level to draw the cooktop centerline location.
• Measure 16-3/4” up from the horizontal line indicating
the bottom of the hood. Draw another horizontal line to
indicate the bottom of the installation bar.
• Use a level to draw the cooktop or range centeline
location.
For Ceiling Ducting:
• If venting out the ceiling, extend the centerline forward
on the ceiling to the back wall.
- Measure 6-1/4” from back wall to mark center point.
- Cut 10” dia. duct hole from center point on the
ceiling.
Venting Through a Soffit:
• Follow the same procedure for ceiling ducting to cut
the hole through the top of the soffit.
For Ducting Through Rear Wall:
NOTE: Check to make sure back damper will not
interfere with studs, electrical or plumbing before making
cut out.
• Back damper accessory UXBDA812 must be
purchased separately for venting through the rear wall.
• Measure 5-7/8” up along the centerline from the
horizontal line indicating bottom of the hood.
• Make an 10-1/2”x13-1/4” cut out centered left to right
along the centerline.
House Wiring Location:
• The junction box is located inside the hood body on the
left side. See Illustrations for hood knockout locations.
House wiring may enter the junction box from the rear or
the top of the hood on the left side.
To route house wiring through the ceiling or soffit:
• Cut a hole approximately 1-1/4” dia. forward on the
ceiling 10-1/4” to the left of the centerline.
To route house wiring through the wall:
NOTE: For back venting, the house wiring must be
routed through the rear knockout so it is hidden.
• Measure 15-3/4” from the bottom of the hood and mark
location
• Cut a hole approximately 1-1/4” dia. at the marked
location at a distance 10-1/4” to the left of the
centerline based on table below.
• Remove top or rear knockout depending on your
installation.
Centerline to Wall
FOR CEILING VENT
DUCTING
Duct Hole
Top of Hood
Installation
Bar
Bottom of Hood
FOR REAR WALL DUCTING
6-5/8”
5-7/8”
10-1/2”
16-3/4”
1-1/4”
Top View
Rear View
10-1/4”
10-1/4”
15-3/4”